RE: [PATCH 3/9] remoteproc: add support to skip firmware load when recovery

[Peng Fan]

> Subject: Re: [PATCH 3/9] remoteproc: add support to skip firmware load when
> recovery
> 
> Hi,
> 
> On 2/19/20 8:27 AM, peng.fan@xxxxxxx wrote:
> > From: Peng Fan <peng.fan@xxxxxxx>
> >
> > Remote processor such as M4 inside i.MX8QXP is not handled by Linux
> > when it is configured to run inside its own hardware partition by
> > system control unit(SCU). So even remote processor crash reset, it is
> > handled by SCU, not linux. To such case, firmware load should be
> > ignored, So introduce skip_fw_load_recovery and platform driver should
> > set it if needed.
> >
> > Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
> > ---
> >  drivers/remoteproc/remoteproc_core.c | 19 +++++++++++--------
> >  include/linux/remoteproc.h           |  1 +
> >  2 files changed, 12 insertions(+), 8 deletions(-)
> >
> > diff --git a/drivers/remoteproc/remoteproc_core.c
> > b/drivers/remoteproc/remoteproc_core.c
> > index 876b5420a32b..ca310e3582bf 100644
> > --- a/drivers/remoteproc/remoteproc_core.c
> > +++ b/drivers/remoteproc/remoteproc_core.c
> > @@ -1678,20 +1678,23 @@ int rproc_trigger_recovery(struct rproc *rproc)
> >  	if (ret)
> >  		goto unlock_mutex;
> >
> > -	/* generate coredump */
> > -	rproc_coredump(rproc);
> > +	if (!rproc->skip_fw_load_recovery) {
> > +		/* generate coredump */
> > +		rproc_coredump(rproc);
> >
> > -	/* load firmware */
> > -	ret = request_firmware(&firmware_p, rproc->firmware, dev);
> > -	if (ret < 0) {
> > -		dev_err(dev, "request_firmware failed: %d\n", ret);
> > -		goto unlock_mutex;
> > +		/* load firmware */
> > +		ret = request_firmware(&firmware_p, rproc->firmware, dev);
> > +		if (ret < 0) {
> > +			dev_err(dev, "request_firmware failed: %d\n", ret);
> > +			goto unlock_mutex;
> > +		}
> 
> Any specific reason to not reuse skip_fw_load here?

Just thought firmware needs to be loaded by Linux when remote
processor crash, even if it initially booted ealy.

skip_fw_load just handles first boot which no need firmware.
But if recovery boot needs firwarem, skip_fw_load will not handle.

So I add this new bool.

Actually to my platform, skip_fw_load could work when recovery,
I just think other platforms might need firware load when recovery.

Regards,
Peng. 

> FYI i'm reworking the Loic's patch and i plan to implement the recovery part
> using skip_fw_load...



> 
> Regards
> Arnaud
> 
> >  	}
> >
> >  	/* boot the remote processor up again */
> >  	ret = rproc_start(rproc, firmware_p);
> >
> > -	release_firmware(firmware_p);
> > +	if (!rproc->skip_fw_load_recovery)
> > +		release_firmware(firmware_p);
> >
> >  unlock_mutex:
> >  	mutex_unlock(&rproc->lock);
> > diff --git a/include/linux/remoteproc.h b/include/linux/remoteproc.h
> > index 4fd5bedab4fa..fe6ee253b385 100644
> > --- a/include/linux/remoteproc.h
> > +++ b/include/linux/remoteproc.h
> > @@ -514,6 +514,7 @@ struct rproc {
> >  	bool has_iommu;
> >  	bool auto_boot;
> >  	bool skip_fw_load;
> > +	bool skip_fw_load_recovery;
> >  	struct list_head dump_segments;
> >  	int nb_vdev;
> >  };
> >