Re: [Bug ?] usb :typec :tcpm :fusb302

[Guenter Roeck]

On 1/20/20 12:14 PM, Markus Reichl wrote:
> Hi Guenter,
>
> Am 20.01.20 um 17:04 schrieb Guenter Roeck:
> > On 1/20/20 6:34 AM, Markus Reichl wrote:
> > > Hi Guenter,
> > >
> > > Am 20.01.20 um 15:21 schrieb Guenter Roeck:
> > > > On 1/20/20 3:58 AM, Heikki Krogerus wrote:
> > > > > Hi Markus,
> > > > >
> > > > > On Thu, Jan 09, 2020 at 05:29:07PM +0100, Markus Reichl wrote:
> > > > > > Hi,
> > > > > >
> > > > > > I'm working with a ROC-RK3399-PC arm64 board from firefly, circuit sheet [1].
> > > > > > The board is powered from an USB-C type connector via an FUSB302 PD controller.
> > > > > > With measured 15W+ power consumption it should use higher voltage PD modes than
> > > > > > the standard 5V USB-C mode.
> > > > > >
> > > > > > When I add the related connector node in DTS [2] the FUSB302 initializes
> > > > > > the right PD mode (e.g. 15V/3A).
> > > > > >
> > > > > > But during initialisation the PD is switched off shortly and the board has a blackout.
> > > > > > When I inject a backup supply voltage behind the FUSB302 (e.g. at SYS_12V line) during boot
> > > > > > I can remove the backup after succesfull setting up the PD and the board will run fine.
> > > > > >
> > > > > > Is it possible to change the behaviour of the fusb302 driver to not power down the PD supply
> > > > > > during init?
> > > > >
> > > > > I guess it's also possible that the problem is with tcpm.c instead of
> > > > > fusb302.c. tcpm.c provides the USB PD state matchines. Guenter! Can
> > > > > you take a look at this?
> > > >
> > > > There was always a problem with handoff from the bootloader. tcpm_init() calls
> > > > tcpm_reset_port() which turns vbus and vconn off, which I imagine can
> > > > trigger the situation.
> > > >
> > > > Unfortunately I was never able to solve the puzzle. The Type-C protocol does
> > > > not support any kind of "hand-off" from one component in the system to another.
> > > > If the state machine doesn't start from a clean state, there is pretty
> > > > much no guarantee that it ever synchronizes.
> > > >
> > > > Maybe someone can find a better solution, but when I wrote the code I just
> > > > could not get it to work reliably without resetting everything during
> > > > registration.
> > > >
> > > > Note that v4.4 did not include the upstream tcpm code, suggesting the
> > > > code in the vendor kernel was possibly using a different or backported
> > > > state machine. Impossible to say what was done there without access
> > > > to the code.
> > >
> > > The vendor code for fusb302 is here:
> > > https://github.com/FireflyTeam/kernel/tree/rk3399/firefly/drivers/mfd
> >
> > AFAICS the vendor code don't reset VBUS, and selectively (only) resets the
> > PD state machine in the fusb302 on startup. The tcpm state machine is embedded
> > in the fusb302 driver, making this easier to control.
> >
> > The fusb302 Linux kernel driver, on the other side, resets the entire fusb302
> > on initialization, not just PD (bit 0 of the reset register). Question is if
> > that can be changed to just reset PD (bit 1 of the reset register).
> > Maybe that would already fix the problem. Can you give it a try ?
> >
> > Guenter
>
> I tried
>
> diff --git a/drivers/usb/typec/tcpm/fusb302.c b/drivers/usb/typec/tcpm/fusb302.c
> index ed8655c6af8c..6e15e7b22064 100644
> --- a/drivers/usb/typec/tcpm/fusb302.c
> +++ b/drivers/usb/typec/tcpm/fusb302.c
> @@ -334,11 +334,11 @@ static int fusb302_sw_reset(struct fusb302_chip *chip)
>          int ret = 0;
>   
>          ret = fusb302_i2c_write(chip, FUSB_REG_RESET,
> -                               FUSB_REG_RESET_SW_RESET);
> +                               FUSB_REG_RESET_PD_RESET);
>          if (ret < 0)
> -               fusb302_log(chip, "cannot sw reset the chip, ret=%d", ret);
> +               fusb302_log(chip, "cannot pd reset the chip, ret=%d", ret);
>          else
> -               fusb302_log(chip, "sw reset");
> +               fusb302_log(chip, "pd reset");
>   
>          return ret;
>   }
>
> but did not help, after mmc and ehci initializing the PD-supply gets switched off at 1.95s.

Next step to try would be to skip vbus initialization - drop tcpm_init_vbus()
from tcpm_reset_port(). Can you do that as well ?

Thanks,
Guenter