Re: [PATCH] tty/serial: atmel: fix out of range clock divider handling

From: Richard Genoud
Date: Fri Dec 13 2019 - 04:57:57 EST


Hi,

Le 11/12/2019 Ã 17:29, David Engraf a ÃcritÂ:
> Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode
> register was already written thus the clock selection is ignored.
>
> Fix by writing the mode register after calculating the baudrate.
>
> Signed-off-by: David Engraf <david.engraf@xxxxxxxxx>

It seems that this bug was introduced by:
commit 5bf5635ac170 ("tty/serial: atmel: add fractional baud rate support")

Could you add the "Fixes:" header ?

Ludovic, could you check if this was your intent at the time ?

> ---
> drivers/tty/serial/atmel_serial.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index a8dc8af83f39..9983e2fabbac 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -2270,9 +2270,6 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> mode |= ATMEL_US_USMODE_NORMAL;
> }
>
I think it's better to mo move the "Set baud rate" block here (cf bellow)

> - /* set the mode, clock divisor, parity, stop bits and data size */
> - atmel_uart_writel(port, ATMEL_US_MR, mode);
> -
> /*
> * when switching the mode, set the RTS line state according to the
> * new mode, otherwise keep the former state
> @@ -2315,6 +2312,9 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
> }
> quot = cd | fp << ATMEL_US_FP_OFFSET;
>
> + /* set the mode, clock divisor, parity, stop bits and data size */
> + atmel_uart_writel(port, ATMEL_US_MR, mode);
> +
I think your patch is good, but I'll be happier if instead of moving
those 2 lines here, the whole "Set the baud rate" block was moved before
"atmel_uart_writel(port, ATMEL_US_MR, mode);"

That's because at line 2291 the ATMEL_US_CR register is set with
ATMEL_US_RTSDIS or ATMEL_US_RTSEN.
And those 2 values have a different effect depending on US_MR.USART_MODE

Quoting from the relase manual:
RTSEN:
1: Drives RTS pin to 1 if US_MR.USART_MODE field = 2, else drives RTS
pin to 0 if US_MR.USART_MODE field = 0.

RTSDIS:
1: Drives RTS pin to 0 if US_MR.USART_MODE field = 2, else drives RTS
pin to 1 if US_MR.USART_MODE field = 0.

So, I think it's better to set the mode register before setting the
control register.


> if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
> atmel_uart_writel(port, ATMEL_US_BRGR, quot);
> atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
>

Thanks !