Re: [PATCH] drivers: thermal: step_wise: add support for hysteresis

From: Daniel Lezcano
Date: Wed Dec 11 2019 - 08:35:08 EST


On 21/11/2019 06:50, Amit Kucheria wrote:
> From: Ram Chandrasekar <rkumbako@xxxxxxxxxxxxxx>
>
> Currently, step wise governor increases the mitigation when the
> temperature goes above a threshold and decreases the mitigation when the
> temperature goes below the threshold.
>
> If there is a case where the
> temperature is wavering around the threshold, the mitigation will be
> applied and removed every iteration, which is not very efficient.
>
> The use of hysteresis temperature could avoid this ping-pong of
> mitigation by relaxing the mitigation to happen only when the
> temperature goes below this lower hysteresis value.

What I'm worried about is how the hysteresis is used in the current
code, where the destination of this data is to set the value in the
sensor hardware if it is supported.

Using the hysteresis in the governor seems like abusing the initial
purpose of this information.

Moreover, the hysteresis creates a gray area where the above algorithm
(DROPPING && !throttle) => state-- or (RAISING && throttle) => state++
may drop the performances because we will continue mitigating even below
the threshold.

As the governor is an open-loop controller, I'm not sure if we can do
something except adding some kind of low pass filter to prevent
mitigation bounces.

> Signed-off-by: Ram Chandrasekar <rkumbako@xxxxxxxxxxxxxx>
> Signed-off-by: Lina Iyer <ilina@xxxxxxxxxxxxxx>
> [Rebased patch from downstream]
> Signed-off-by: Amit Kucheria <amit.kucheria@xxxxxxxxxx>
> ---
> drivers/thermal/step_wise.c | 35 ++++++++++++++++++++++++-----------
> 1 file changed, 24 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/thermal/step_wise.c b/drivers/thermal/step_wise.c
> index 6e051cbd824ff..2c8a34a7cf959 100644
> --- a/drivers/thermal/step_wise.c
> +++ b/drivers/thermal/step_wise.c
> @@ -24,7 +24,7 @@
> * for this trip point
> * d. if the trend is THERMAL_TREND_DROP_FULL, use lower limit
> * for this trip point
> - * If the temperature is lower than a trip point,
> + * If the temperature is lower than a hysteresis temperature,
> * a. if the trend is THERMAL_TREND_RAISING, do nothing
> * b. if the trend is THERMAL_TREND_DROPPING, use lower cooling
> * state for this trip point, if the cooling state already
> @@ -115,30 +115,31 @@ static void update_passive_instance(struct thermal_zone_device *tz,
>
> static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
> {
> - int trip_temp;
> + int trip_temp, hyst_temp;
> enum thermal_trip_type trip_type;
> enum thermal_trend trend;
> struct thermal_instance *instance;
> - bool throttle = false;
> + bool throttle;
> int old_target;
>
> if (trip == THERMAL_TRIPS_NONE) {
> - trip_temp = tz->forced_passive;
> + hyst_temp = trip_temp = tz->forced_passive;
> trip_type = THERMAL_TRIPS_NONE;
> } else {
> tz->ops->get_trip_temp(tz, trip, &trip_temp);
> + hyst_temp = trip_temp;
> + if (tz->ops->get_trip_hyst) {
> + tz->ops->get_trip_hyst(tz, trip, &hyst_temp);
> + hyst_temp = trip_temp - hyst_temp;
> + }
> tz->ops->get_trip_type(tz, trip, &trip_type);
> }
>
> trend = get_tz_trend(tz, trip);
>
> - if (tz->temperature >= trip_temp) {
> - throttle = true;
> - trace_thermal_zone_trip(tz, trip, trip_type);
> - }
> -
> - dev_dbg(&tz->device, "Trip%d[type=%d,temp=%d]:trend=%d,throttle=%d\n",
> - trip, trip_type, trip_temp, trend, throttle);
> + dev_dbg(&tz->device,
> + "Trip%d[type=%d,temp=%d,hyst=%d]:trend=%d,throttle=%d\n",
> + trip, trip_type, trip_temp, hyst_temp, trend, throttle);
>
> mutex_lock(&tz->lock);
>
> @@ -147,6 +148,18 @@ static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip)
> continue;
>
> old_target = instance->target;
> + throttle = false;
> + /*
> + * Lower the mitigation only if the temperature
> + * goes below the hysteresis temperature.
> + */
> + if (tz->temperature >= trip_temp ||
> + (tz->temperature >= hyst_temp &&
> + old_target != THERMAL_NO_TARGET)) {
> + throttle = true;
> + trace_thermal_zone_trip(tz, trip, trip_type);
> + }
> +
> instance->target = get_target_state(instance, trend, throttle);
> dev_dbg(&instance->cdev->device, "old_target=%d, target=%d\n",
> old_target, (int)instance->target);
>


--
<http://www.linaro.org/> Linaro.org â Open source software for ARM SoCs

Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog