Re: [PATCH 2/2] clk: meson: a1: add support for Amlogic A1 clock driver
From: Jian Hu
Date: Fri Sep 27 2019 - 05:54:30 EST
Hi, Jerome
Thank you for review.
On 2019/9/25 23:09, Jerome Brunet wrote:
On Wed 25 Sep 2019 at 19:44, Jian Hu <jian.hu@xxxxxxxxxxx> wrote:
The Amlogic A1 clock includes three parts:
peripheral clocks, pll clocks, CPU clocks.
sys pll and CPU clocks will be sent in next patch.
Unlike the previous series, there is no EE/AO domain
in A1 CLK controllers.
Signed-off-by: Jian Hu <jian.hu@xxxxxxxxxxx>
Signed-off-by: Jianxin Pan <jianxin.pan@xxxxxxxxxxx>
---
arch/arm64/Kconfig.platforms | 1 +
drivers/clk/meson/Kconfig | 10 +
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/a1.c | 2617 ++++++++++++++++++++++++++++++++++++++++++
drivers/clk/meson/a1.h | 172 +++
5 files changed, 2801 insertions(+)
create mode 100644 drivers/clk/meson/a1.c
create mode 100644 drivers/clk/meson/a1.h
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 16d7614..a48f67d 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -138,6 +138,7 @@ config ARCH_MESON
select COMMON_CLK_AXG
select COMMON_CLK_G12A
select MESON_IRQ_GPIO
+ select COMMON_CLK_A1
This need to be separate patch addressed to Kevin once your driver is merged
ok, I will remove it in PATCH V2. And send it again after the driver is
merged.
help
This enables support for the arm64 based Amlogic SoCs
such as the s905, S905X/D, S912, A113X/D or S905X/D2
diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index dabeb43..e6cb4c3 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -107,3 +107,13 @@ config COMMON_CLK_G12A
help
Support for the clock controller on Amlogic S905D2, S905X2 and S905Y2
devices, aka g12a. Say Y if you want peripherals to work.
+
+config COMMON_CLK_A1
+ bool
+ depends on ARCH_MESON
+ select COMMON_CLK_MESON_REGMAP
+ select COMMON_CLK_MESON_DUALDIV
+ select COMMON_CLK_MESON_PLL
+ help
+ Support for the clock controller on Amlogic A113L device,
+ aka a1. Say Y if you want peripherals to work.
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 3939f21..6be3a8f 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -19,3 +19,4 @@ obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
+obj-$(CONFIG_COMMON_CLK_A1) += a1.o
diff --git a/drivers/clk/meson/a1.c b/drivers/clk/meson/a1.c
new file mode 100644
index 0000000..26edae0f
--- /dev/null
+++ b/drivers/clk/meson/a1.c
@@ -0,0 +1,2617 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/init.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include "clk-mpll.h"
+#include "clk-pll.h"
+#include "clk-regmap.h"
+#include "vid-pll-div.h"
+#include "clk-dualdiv.h"
+#include "meson-eeclk.h"
+#include "a1.h"
+
+/* PLLs clock in gates, its parent is xtal */
+static struct clk_regmap a1_xtal_clktree = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_clktree",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
Is CCF even expected to touch this ever ? what about RO ops ?
Please review your other clocks with this in mind
the clock should not be changed at runtime.clk_regmap_gate_ro_ops
is a good idea. Set RO ops and remove the CLK_IS_CRITICAL flag.
+ },
+};
+
+static struct clk_regmap a1_xtal_fixpll = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_fixpll",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_regmap a1_xtal_usb_phy = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 2,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_usb_phy",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
How is an USB clock critical to the system ?
Please review your other clocks with comment in mind ...
the usb clock does not affect the system,
remove the CLK_IS_CRITICAL flag
+ },
+};
+
+static struct clk_regmap a1_xtal_usb_ctrl = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 3,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_usb_ctrl",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
+ },
+};
the usb clock does not affect the system,
remove the CLK_IS_CRITICAL flag
+
+static struct clk_regmap a1_xtal_hifipll = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 4,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_hifipll",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
+ },
+};
CLK_IS_CRITICAL is need to lock hifi pll.
+
+static struct clk_regmap a1_xtal_syspll = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 5,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_syspll",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
when CPU clock is at fixed clock, sys pll
will be disabled, xtal_syspll will be disabled too.
when setting sys pll, call clk_set_rate to lock
sys pll, add RO ops to avoid disabling the clock
+static struct clk_regmap a1_xtal_dds = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 6,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_dds",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ .flags = CLK_IS_CRITICAL,
+ },
+};
CLK_IS_CRITICAL is need to lock dds
+
+/* fixed pll = 1536M
+ *
+ * fixed pll ----- fclk_div2 = 768M
+ * |
+ * ----- fclk_div3 = 512M
+ * |
+ * ----- fclk_div5 = 307.2M
+ * |
+ * ----- fclk_div7 = 219.4M
+ */
The framework will make those calculation ... you can remove this
ok, I will remote the comment.
+static struct clk_regmap a1_fixed_pll_dco = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .frac = {
+ .reg_off = ANACTRL_FIXPLL_CTRL1,
+ .shift = 0,
+ .width = 19,
+ },
+ .l = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 31,
+ .width = 1,
+ },
+ .rst = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 29,
+ .width = 1,
+ },
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fixed_pll_dco",
+ .ops = &meson_clk_pll_ro_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_xtal_fixpll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fixed_pll = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 20,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "fixed_pll",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fixed_pll_dco.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+};
+
+static const struct pll_params_table a1_hifi_pll_params_table[] = {
+ PLL_PARAMS(128, 5), /* DCO = 614.4M */
+};
+
+static const struct reg_sequence a1_hifi_init_regs[] = {
+ { .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
+ { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
+ { .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x10022200 },
+ { .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00301000 },
+ { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f19480 },
+ { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x11f19480, .delay_us = 10 },
+ { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x15f11480, .delay_us = 40 },
+ { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001140 },
+ { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
+};
+
+/*
+ * The Meson A1 HIFI PLL is 614.4M, it requires
+ * a strict register sequence to enable the PLL.
+ * set meson_clk_pcie_pll_ops as its ops
+ */
Could you elaborate on this ? What need to be done to enable the clock ?
Also the HIFI PLL used to be able to do a *LOT* of different rate which
might be desirable for audio use case. Why is this one restricted to one
particular rate ?
The audio working frequency are 44.1khz, 48khz and 192khz.
614.4M can meet the three frequency.
after the hifi pll, there are two dividers in Audio clock.
614.4M/3200 = 192khz
614.4M/12800 = 48khz
614,4M/13932 = 44.0999khz
+static struct clk_regmap a1_hifi_pll = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .frac = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL1,
+ .shift = 0,
+ .width = 19,
+ },
+ .l = {
+ .reg_off = ANACTRL_HIFIPLL_STS,
+ .shift = 31,
+ .width = 1,
+ },
+ .table = a1_hifi_pll_params_table,
+ .init_regs = a1_hifi_init_regs,
+ .init_count = ARRAY_SIZE(a1_hifi_init_regs),
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "hifi_pll",
+ .ops = &meson_clk_pcie_pll_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_xtal_hifipll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_fixed_factor a1_fclk_div2_div = {
+ .mult = 1,
+ .div = 2,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fclk_div2 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 21,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fclk_div2_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
+ * or its children clocks.
+ */
The meaning of this flag is already documented in clk-provider.h
The reason why you need this flag is lot more interesting here ...
Same below
ok, I will replace new comments here.
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_fixed_factor a1_fclk_div3_div = {
+ .mult = 1,
+ .div = 3,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div3_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fclk_div3 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 22,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div3",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fclk_div3_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
+ * its children clocks.
+ */
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_fixed_factor a1_fclk_div5_div = {
+ .mult = 1,
+ .div = 5,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div5_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fclk_div5 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 23,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div5",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fclk_div5_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
+ * its children clocks.
+ */
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_fixed_factor a1_fclk_div7_div = {
+ .mult = 1,
+ .div = 7,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div7_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fclk_div7 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 23,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div7",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fclk_div7_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * add CLK_IS_CRITICAL flag to avoid being disabled by clk core
+ * or its children clock.
+ */
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+/* sys clk = 64M */
Again this comment does not help understanding the driver code, please
remove
got it.
+static u32 mux_table_sys_ab_clk[] = { 0, 1, 2, 3};
This table is useless
+static const struct clk_parent_data sys_ab_clk_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &a1_fclk_div2.hw },
+ { .hw = &a1_fclk_div3.hw },
+ { .hw = &a1_fclk_div5.hw },
+};
+
+static struct clk_regmap a1_sys_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_sys_ab_clk,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_b_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_data = sys_ab_clk_parent_data,
+ .num_parents = ARRAY_SIZE(sys_ab_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_sys_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SYS_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_sys_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_sys_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sys_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_sys_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
Why does this need to be critical ?
The a1_sys_clk (leaf of the block) could possibly be critical (if you
explain why) ... but the flag should not be needed in the middle of the
block
ok, the a1_sys_clk should not be changed at runtime, it is the same with
the clk81 clock in G12A. Just use another name in A1.
+ },
+};
+
+static struct clk_regmap a1_sys_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_sys_ab_clk,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_a_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_data = sys_ab_clk_parent_data,
+ .num_parents = ARRAY_SIZE(sys_ab_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_sys_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SYS_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_sys_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_sys_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sys_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_sys_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_regmap a1_sys_clk = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 31,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_clk",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_sys_a.hw, &a1_sys_b.hw,
+ },
+ .num_parents = 2,
SET_RATE_PARENT ?
the ops is RO, Maybe no flag is better.
+ },
+};
+
+/* rtc 32k clock in */
+static struct clk_regmap a1_rtc_32k_clkin = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "rtc_32k_clkin",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static const struct meson_clk_dualdiv_param a1_32k_div_table[] = {
+ {
+ .dual = 1,
+ .n1 = 733,
+ .m1 = 8,
+ .n2 = 732,
+ .m2 = 11,
+ }, {}
+};
+
+static struct clk_regmap a1_rtc_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = RTC_BY_OSCIN_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = RTC_BY_OSCIN_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = a1_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_rtc_32k_clkin.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_rtc_32k_xtal = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL1,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "rtc_32k_xtal",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_rtc_32k_clkin.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static u32 rtc_32k_sel[] = { 0, 1 };
useless
ok, I will delete the table.
+
+static struct clk_regmap a1_rtc_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = RTC_CTRL,
+ .mask = 0x3,
+ .shift = 0,
+ .table = rtc_32k_sel,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_rtc_32k_xtal.hw,
+ &a1_rtc_32k_div.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+struct clk_regmap a1_rtc_clk = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_clk",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_rtc_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/* dsp a clk */
+static u32 mux_table_dsp_ab[] = { 0, 1, 2, 3, 4, 7 };
+static const struct clk_parent_data dsp_ab_clk_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &a1_fclk_div2.hw },
+ { .hw = &a1_fclk_div3.hw },
+ { .hw = &a1_fclk_div5.hw },
+ { .hw = &a1_hifi_pll.hw },
+ { .hw = &a1_rtc_clk.hw },
+};
+
+static struct clk_regmap a1_dspa_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_clk_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_dspa_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPA_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspa_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dspa_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspa_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
This CLK_IGNORE_UNUSED, if justified, needs to be explained
ok, DSP cowork withe ARM in A1, dsp clock shoud not be changed at runtime.
+ },
+};
+
+static struct clk_regmap a1_dspa_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_clk_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_dspa_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPA_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspa_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dspa_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspa_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_regmap a1_dspa_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &a1_dspa_a.hw },
+ { .hw = &a1_dspa_b.hw },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dspa_en_dspa = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_EN,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_en_dspa",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspa_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_regmap a1_dspa_en_nic = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_EN,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_en_nic",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspa_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+/* dsp b clk */
+static struct clk_regmap a1_dspb_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_clk_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_dspb_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPB_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dspb_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_regmap a1_dspb_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_clk_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_dspb_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPB_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dspb_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_regmap a1_dspb_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_a.hw, &a1_dspb_b.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dspb_en_dspb = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_EN,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_en_dspb",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_regmap a1_dspb_en_nic = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_EN,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_en_nic",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dspb_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+/* 12M/24M clock */
+static struct clk_regmap a1_24m = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "24m",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_fixed_factor a1_24m_div2 = {
+ .mult = 1,
+ .div = 2,
+ .hw.init = &(struct clk_init_data){
+ .name = "24m_div2",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_24m.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_12m = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 10,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "12m",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_24m_div2.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fclk_div2_divn_pre = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = CLK12_24_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_divn_pre",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fclk_div2.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap a1_fclk_div2_divn = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 12,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_divn",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_fclk_div2_divn_pre.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/* gen clk */
Either put something helpful or don't put anything
For example explaining why there is a hole in the table bellow and what
is parent 4 (if any) would be helpful.
ok, parent 2 is sys_pll_div16, sys pll and related clock are not
completeed, parent 4 is one of clock measurement source, it relies on
the clock measurement register configuration.
gen clock is a debug and monitor clock.
+static u32 gen_clk_table[] = { 0, 1, 3, 5, 6, 7, 8 };
+static const struct clk_parent_data gen_clk_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &a1_rtc_clk.hw },
+ { .hw = &a1_hifi_pll.hw },
+ { .hw = &a1_fclk_div2.hw },
+ { .hw = &a1_fclk_div3.hw },
+ { .hw = &a1_fclk_div5.hw },
+ { .hw = &a1_fclk_div7.hw },
+};
+
+static struct clk_regmap a1_gen_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = GEN_CLK_CTRL,
+ .mask = 0xf,
+ .shift = 12,
+ .table = gen_clk_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "gen_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = gen_clk_parent_data,
+ .num_parents = ARRAY_SIZE(gen_clk_parent_data),
+ },
+};
+
+static struct clk_regmap a1_gen_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = GEN_CLK_CTRL,
+ .shift = 0,
+ .width = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "gen_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_gen_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_gen = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = GEN_CLK_CTRL,
+ .bit_idx = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "gen",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_gen_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_saradc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "saradc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .fw_name = "xtal", },
+ { .hw = &a1_sys_clk.hw, },
+ },
+ .num_parents = 2,
+ },
+};
+
+static struct clk_regmap a1_saradc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "saradc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_saradc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_saradc_clk = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "saradc_clk",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_saradc_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/* pwm a/b/c/d parent data */
+static const struct clk_parent_data pwm_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &a1_sys_clk.hw },
+};
+
+/*
+ * add CLK_IGNORE_UNUSED flag for pwm controller GATE
+ * clk core will disable unused clock, it may disable
+ * vddcore voltage which contrlled by one pwm in bl21.
^
typo
+ * add the flag to avoid changing cpu voltage.
80 char per line is ok
This comment would be better placed next to the corresponding flag
Also you could explain that flag could be removed when CCF has some
hand-off mechanism (similar comments you can copy in other driver)
ok, contrlled --> controlled
I will move the comment next to the flag
I have gotten the similar comments in g12a.c
+ */
+/* pwm a clk */
+static struct clk_regmap a1_pwm_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_parent_data,
+ .num_parents = ARRAY_SIZE(pwm_parent_data),
+ },
+};
+
+static struct clk_regmap a1_pwm_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_pwm_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_pwm_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_pwm_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
[...]
+/* usb bus clk */
+static const struct clk_parent_data usb_bus_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &a1_sys_clk.hw },
+ { .hw = &a1_fclk_div3.hw },
+ { .hw = &a1_fclk_div5.hw },
+};
+
+static struct clk_regmap a1_usb_bus_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = USB_BUSCLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "usb_bus_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = usb_bus_parent_data,
+ .num_parents = ARRAY_SIZE(usb_bus_parent_data),
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
Again, every unused flag need to be properly explained
ok, I will confirm this flag
+ },
+};
+
+static struct clk_regmap a1_usb_bus_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = USB_BUSCLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "usb_bus_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_usb_bus_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_regmap a1_usb_bus = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = USB_BUSCLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_bus",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_usb_bus_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
[...]
+
+/* dmc clk */
+static const struct clk_hw *dmc_parent_hws[] = {
+ &a1_fclk_div2.hw,
+ &a1_fclk_div3.hw,
+ &a1_fclk_div5.hw,
+ &a1_hifi_pll.hw,
+};
+
+static struct clk_regmap a1_dmc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DMC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = dmc_parent_hws,
+ .num_parents = ARRAY_SIZE(dmc_parent_hws),
+ },
+};
+
+static struct clk_regmap a1_dmc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DMC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dmc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dmc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DMC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &a1_dmc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap a1_dmc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DMC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dmc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &a1_dmc_sel2.hw
+ },
+ .num_parents = 1,
+ /*
+ * add CLK_IGNORE_UNUSED to avoid hangup
+ * DDR clock should not change at runtime
+ */
CRITICAL ? RO ops maybe ?
RO ops is better
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
[...]
+
+#define MESON_GATE(_name, _reg, _bit) \
+ MESON_PCLK(_name, _reg, _bit, &a1_sys_clk.hw)
+
+/* CLKTREE_SYS_CLK_EN0 */
Full caps is not ok ... and once again, try to add comment which helps
ok, I will add some useful comment.
+static MESON_GATE(a1_clk_tree, SYS_CLK_EN0, 0);
+static MESON_GATE(a1_reset_ctrl, SYS_CLK_EN0, 1);
+static MESON_GATE(a1_analog_ctrl, SYS_CLK_EN0, 2);
+static MESON_GATE(a1_pwr_ctrl, SYS_CLK_EN0, 3);
+static MESON_GATE(a1_pad_ctrl, SYS_CLK_EN0, 4);
+static MESON_GATE(a1_sys_ctrl, SYS_CLK_EN0, 5);
+static MESON_GATE(a1_temp_sensor, SYS_CLK_EN0, 6);
+static MESON_GATE(a1_am2axi_dev, SYS_CLK_EN0, 7);
+static MESON_GATE(a1_spicc_b, SYS_CLK_EN0, 8);
+static MESON_GATE(a1_spicc_a, SYS_CLK_EN0, 9);
+static MESON_GATE(a1_clk_msr, SYS_CLK_EN0, 10);
+static MESON_GATE(a1_audio, SYS_CLK_EN0, 11);
+static MESON_GATE(a1_jtag_ctrl, SYS_CLK_EN0, 12);
+static MESON_GATE(a1_saradc, SYS_CLK_EN0, 13);
+static MESON_GATE(a1_pwm_ef, SYS_CLK_EN0, 14);
+static MESON_GATE(a1_pwm_cd, SYS_CLK_EN0, 15);
+static MESON_GATE(a1_pwm_ab, SYS_CLK_EN0, 16);
+static MESON_GATE(a1_cec, SYS_CLK_EN0, 17);
+static MESON_GATE(a1_i2c_s, SYS_CLK_EN0, 18);
+static MESON_GATE(a1_ir_ctrl, SYS_CLK_EN0, 19);
+static MESON_GATE(a1_i2c_m_d, SYS_CLK_EN0, 20);
+static MESON_GATE(a1_i2c_m_c, SYS_CLK_EN0, 21);
+static MESON_GATE(a1_i2c_m_b, SYS_CLK_EN0, 22);
+static MESON_GATE(a1_i2c_m_a, SYS_CLK_EN0, 23);
+static MESON_GATE(a1_acodec, SYS_CLK_EN0, 24);
+static MESON_GATE(a1_otp, SYS_CLK_EN0, 25);
+static MESON_GATE(a1_sd_emmc_a, SYS_CLK_EN0, 26);
+static MESON_GATE(a1_usb_phy, SYS_CLK_EN0, 27);
+static MESON_GATE(a1_usb_ctrl, SYS_CLK_EN0, 28);
+static MESON_GATE(a1_sys_dspb, SYS_CLK_EN0, 29);
+static MESON_GATE(a1_sys_dspa, SYS_CLK_EN0, 30);
+static MESON_GATE(a1_dma, SYS_CLK_EN0, 31);
+/* CLKTREE_SYS_CLK_EN1 */
+static MESON_GATE(a1_irq_ctrl, SYS_CLK_EN1, 0);
+static MESON_GATE(a1_nic, SYS_CLK_EN1, 1);
+static MESON_GATE(a1_gic, SYS_CLK_EN1, 2);
+static MESON_GATE(a1_uart_c, SYS_CLK_EN1, 3);
+static MESON_GATE(a1_uart_b, SYS_CLK_EN1, 4);
+static MESON_GATE(a1_uart_a, SYS_CLK_EN1, 5);
+static MESON_GATE(a1_sys_psram, SYS_CLK_EN1, 6);
+static MESON_GATE(a1_rsa, SYS_CLK_EN1, 8);
+static MESON_GATE(a1_coresight, SYS_CLK_EN1, 9);
+/* CLKTREE_AXI_CLK_EN */
+static MESON_GATE(a1_am2axi_vad, AXI_CLK_EN, 0);
+static MESON_GATE(a1_audio_vad, AXI_CLK_EN, 1);
+static MESON_GATE(a1_axi_dmc, AXI_CLK_EN, 3);
+static MESON_GATE(a1_axi_psram, AXI_CLK_EN, 4);
+static MESON_GATE(a1_ramb, AXI_CLK_EN, 5);
+static MESON_GATE(a1_rama, AXI_CLK_EN, 6);
+static MESON_GATE(a1_axi_spifc, AXI_CLK_EN, 7);
+static MESON_GATE(a1_axi_nic, AXI_CLK_EN, 8);
+static MESON_GATE(a1_axi_dma, AXI_CLK_EN, 9);
+static MESON_GATE(a1_cpu_ctrl, AXI_CLK_EN, 10);
+static MESON_GATE(a1_rom, AXI_CLK_EN, 11);
+static MESON_GATE(a1_prod_i2c, AXI_CLK_EN, 12);
+
[...]
+
+/* Convenience table to populate regmap in .probe
+ * Peripheral clock register base address is 0xfe000800
this info will be in DT
I will remove the address commit
+ */
[...]
+
+/*
+ * cpu clock register base address is 0xfd000080
+ */
+static struct clk_regmap *const a1_cpu_clk_regmaps[] = {
+ /* TODO */
+};
+
+/*
+ * pll clock register base address is 0xfe007c00
+ */
+static struct clk_regmap *const a1_pll_clk_regmaps[] = {
+ &a1_fixed_pll_dco,
+ &a1_fixed_pll,
+ &a1_hifi_pll,
+ &a1_fclk_div2,
+ &a1_fclk_div3,
+ &a1_fclk_div5,
+ &a1_fclk_div7,
+};
+
+static struct regmap_config clkc_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static struct regmap *a1_regmap_resource(struct device *dev, char *name)
+{
+ struct resource res;
+ void __iomem *base;
+ int i;
+ struct device_node *node = dev->of_node;
+
+ i = of_property_match_string(node, "reg-names", name);
+ if (of_address_to_resource(node, i, &res))
+ return ERR_PTR(-ENOENT);
+
+ base = devm_ioremap_resource(dev, &res);
+ if (IS_ERR(base))
+ return ERR_CAST(base);
+
+ clkc_regmap_config.max_register = resource_size(&res) - 4;
+ clkc_regmap_config.name = devm_kasprintf(dev, GFP_KERNEL,
+ "%s-%s", node->name,
+ name);
+ if (!clkc_regmap_config.name)
+ return ERR_PTR(-ENOMEM);
+
+ return devm_regmap_init_mmio(dev, base, &clkc_regmap_config);
+}
+
+static int a1_clkc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct regmap *peripheral_map, *pll_map, *cpu_map;
+ int ret, i;
+
+ /* Get regmap for different clock area */
+ peripheral_map = a1_regmap_resource(dev, "peripheral");
+ if (IS_ERR(peripheral_map)) {
+ dev_err(dev, "peripheral clk registers not found\n");
+ return PTR_ERR(peripheral_map);
+ }
+
+ pll_map = a1_regmap_resource(dev, "pll");
+ if (IS_ERR(pll_map)) {
+ dev_err(dev, "pll clk registers not found\n");
+ return PTR_ERR(pll_map);
+ }
+
+ cpu_map = a1_regmap_resource(dev, "cpu");
+ if (IS_ERR(cpu_map)) {
+ dev_err(dev, "cpu clk registers not found\n");
+ return PTR_ERR(cpu_map);
+ }
+
+ /* Populate regmap for the regmap backed clocks */
+ for (i = 0; i < ARRAY_SIZE(a1_clk_regmaps); i++)
+ a1_clk_regmaps[i]->map = peripheral_map;
+
+ for (i = 0; i < ARRAY_SIZE(a1_cpu_clk_regmaps); i++)
+ a1_cpu_clk_regmaps[i]->map = cpu_map;
+
+ for (i = 0; i < ARRAY_SIZE(a1_pll_clk_regmaps); i++)
+ a1_pll_clk_regmaps[i]->map = pll_map;
Unless you have a rock solid reason why you absolutely need to make
single controller out of this 3 regions, Nack.
As comment replying in
Documentation/devicetree/bindings/clock/amlogic,a1-clkc.yaml, I will
implement three clock drivers.
+
+ for (i = 0; i < a1_hw_onecell_data.num; i++) {
+ /* array might be sparse */
+ if (!a1_hw_onecell_data.hws[i])
+ continue;
+
+ ret = devm_clk_hw_register(dev, a1_hw_onecell_data.hws[i]);
+ if (ret) {
+ dev_err(dev, "Clock registration failed\n");
+ return ret;
+ }
+ }
+
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+ &a1_hw_onecell_data);
+}
+
+static const struct of_device_id clkc_match_table[] = {
+ { .compatible = "amlogic,a1-clkc" },
+ { /* sentinel */ }
+};
+
+static struct platform_driver a1_driver = {
+ .probe = a1_clkc_probe,
+ .driver = {
+ .name = "a1-clkc",
+ .of_match_table = clkc_match_table,
+ },
+};
+
+builtin_platform_driver(a1_driver);
diff --git a/drivers/clk/meson/a1.h b/drivers/clk/meson/a1.h
new file mode 100644
index 0000000..f2291c4
--- /dev/null
+++ b/drivers/clk/meson/a1.h
@@ -0,0 +1,172 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ */
+
+#ifndef __A1_H
+#define __A1_H
+
+/*
+ * peripheral clock controller register address
+ * APB_BASE: APB0_BASE_ADDR = 0xfe000800
Again this info is DT and might become wrong if your controller is ever
compatible with another SoC
I will remove the address comment, the right address is 0xfe000080.
+ */
+#define SYS_OSCIN_CTRL 0x0
+#define RTC_BY_OSCIN_CTRL0 0x4
+#define RTC_BY_OSCIN_CTRL1 0x8
+#define RTC_CTRL 0xc
+#define SYS_CLK_CTRL0 0x10
+#define AXI_CLK_CTRL0 0x14
+#define SYS_CLK_EN0 0x1c
+#define SYS_CLK_EN1 0x20
+#define AXI_CLK_EN 0x24
+#define DSPA_CLK_EN 0x28
+#define DSPB_CLK_EN 0x2c
+#define DSPA_CLK_CTRL0 0x30
+#define DSPB_CLK_CTRL0 0x34
+#define CLK12_24_CTRL 0x38
+#define GEN_CLK_CTRL 0x3c
+#define TIMESTAMP_CTRL0 0x40
+#define TIMESTAMP_CTRL1 0x44
+#define TIMESTAMP_CTRL2 0x48
+#define TIMESTAMP_VAL0 0x4c
+#define TIMESTAMP_VAL1 0x50
+#define TIMEBASE_CTRL0 0x54
+#define TIMEBASE_CTRL1 0x58
+#define SAR_ADC_CLK_CTRL 0xc0
+#define PWM_CLK_AB_CTRL 0xc4
+#define PWM_CLK_CD_CTRL 0xc8
+#define PWM_CLK_EF_CTRL 0xcc
+#define SPICC_CLK_CTRL 0xd0
+#define TS_CLK_CTRL 0xd4
+#define SPIFC_CLK_CTRL 0xd8
+#define USB_BUSCLK_CTRL 0xdc
+#define SD_EMMC_CLK_CTRL 0xe0
+#define CECA_CLK_CTRL0 0xe4
+#define CECA_CLK_CTRL1 0xe8
+#define CECB_CLK_CTRL0 0xec
+#define CECB_CLK_CTRL1 0xf0
+#define PSRAM_CLK_CTRL 0xf4
+#define DMC_CLK_CTRL 0xf8
+#define FCLK_DIV1_SEL 0xfc
+#define TST_CTRL 0x100
+/*
+ * For PLL register offset
+ * APB_BASE: APB0_BASE_ADDR = 0xfe007c00
+ */
+#define ANACTRL_FIXPLL_CTRL0 0x80
+#define ANACTRL_FIXPLL_CTRL1 0x84
+#define ANACTRL_FIXPLL_CTRL2 0x88
+#define ANACTRL_FIXPLL_CTRL3 0x8c
+#define ANACTRL_FIXPLL_CTRL4 0x90
+#define ANACTRL_FIXPLL_STS 0x94
+#define ANACTRL_SYSPLL_CTRL0 0x100
+#define ANACTRL_SYSPLL_CTRL1 0x104
+#define ANACTRL_SYSPLL_CTRL2 0x108
+#define ANACTRL_SYSPLL_CTRL3 0x10c
+#define ANACTRL_SYSPLL_CTRL4 0x110
+#define ANACTRL_SYSPLL_STS 0x114
+#define ANACTRL_HIFIPLL_CTRL0 0x140
+#define ANACTRL_HIFIPLL_CTRL1 0x144
+#define ANACTRL_HIFIPLL_CTRL2 0x148
+#define ANACTRL_HIFIPLL_CTRL3 0x14c
+#define ANACTRL_HIFIPLL_CTRL4 0x150
+#define ANACTRL_HIFIPLL_STS 0x154
+#define ANACTRL_AUDDDS_CTRL0 0x180
+#define ANACTRL_AUDDDS_CTRL1 0x184
+#define ANACTRL_AUDDDS_CTRL2 0x188
+#define ANACTRL_AUDDDS_CTRL3 0x18c
+#define ANACTRL_AUDDDS_CTRL4 0x190
+#define ANACTRL_AUDDDS_STS 0x194
+#define ANACTRL_MISCTOP_CTRL0 0x1c0
+#define ANACTRL_POR_CNTL 0x208
+/*
+ * CPU clok register offset
+ * APB_BASE: APB1_BASE_ADDR = 0xfd000080
+ */
+#define CPUCTRL_CLK_CTRL0 0x00
+#define CPUCTRL_CLK_CTRL1 0x04
+#define CPUCTRL_CLK_CTRL2 0x08
+#define CPUCTRL_CLK_CTRL3 0x0c
+#define CPUCTRL_CLK_CTRL4 0x10
+#define CPUCTRL_CLK_CTRL5 0x14
+#define CPUCTRL_CLK_CTRL6 0x18
+#define CPUCTRL_CLK_CTRL7 0x1c
+
+#define CLKID_FIXED_PLL_DCO 0
+#define CLKID_SYS_A_SEL 10
+#define CLKID_SYS_A_DIV 11
+#define CLKID_SYS_A 12
+#define CLKID_SYS_B_SEL 13
+#define CLKID_SYS_B_DIV 14
+#define CLKID_SYS_B 15
+#define CLKID_XTAL_CLKTREE 18
+#define CLKID_XTAL_FIXPLL 19
+#define CLKID_XTAL_USB_PHY 20
+#define CLKID_XTAL_USB_CTRL 21
+#define CLKID_XTAL_HIFIPLL 22
+#define CLKID_XTAL_SYSPLL 23
+#define CLKID_XTAL_DDS 24
+#define CLKID_DSPA_A_SEL 78
+#define CLKID_DSPA_A_DIV 79
+#define CLKID_DSPA_A 80
+#define CLKID_DSPA_B_SEL 81
+#define CLKID_DSPA_B_DIV 82
+#define CLKID_DSPA_B 83
+#define CLKID_DSPB_A_SEL 85
+#define CLKID_DSPB_A_DIV 86
+#define CLKID_DSPB_A 87
+#define CLKID_DSPB_B_SEL 88
+#define CLKID_DSPB_B_DIV 89
+#define CLKID_DSPB_B 90
+#define CLKID_RTC_32K_CLKIN 96
+#define CLKID_RTC_32K_DIV 97
+#define CLKID_RTC_32K_XTAL 98
+#define CLKID_RTC_32K_SEL 99
+#define CLKID_CECB_32K_CLKIN 106
+#define CLKID_CECB_32K_DIV 107
+#define CLKID_CECB_32K_SEL_PRE 108
+#define CLKID_CECB_32K_SEL 109
+#define CLKID_CECA_32K_CLKIN 101
+#define CLKID_CECA_32K_DIV 102
+#define CLKID_CECA_32K_SEL_PRE 103
+#define CLKID_CECA_32K_SEL 104
+#define CLKID_DIV2_PRE 113
+#define CLKID_24M_DIV2 115
+#define CLKID_GEN_SEL 116
+#define CLKID_GEN_DIV 117
+#define CLKID_SARADC_DIV 120
+#define CLKID_PWM_A_SEL 122
+#define CLKID_PWM_A_DIV 123
+#define CLKID_PWM_B_SEL 125
+#define CLKID_PWM_B_DIV 126
+#define CLKID_PWM_C_SEL 128
+#define CLKID_PWM_C_DIV 129
+#define CLKID_PWM_D_SEL 131
+#define CLKID_PWM_D_DIV 132
+#define CLKID_PWM_E_SEL 134
+#define CLKID_PWM_E_DIV 135
+#define CLKID_PWM_F_SEL 137
+#define CLKID_PWM_F_DIV 138
+#define CLKID_SPICC_SEL 140
+#define CLKID_SPICC_DIV 141
+#define CLKID_SPICC_SEL2 142
+#define CLKID_TS_DIV 144
+#define CLKID_SPIFC_SEL 146
+#define CLKID_SPIFC_DIV 147
+#define CLKID_SPIFC_SEL2 148
+#define CLKID_USB_BUS_SEL 150
+#define CLKID_USB_BUS_DIV 151
+#define CLKID_SD_EMMC_SEL 153
+#define CLKID_SD_EMMC_DIV 154
+#define CLKID_SD_EMMC_SEL2 155
+#define CLKID_PSRAM_SEL 157
+#define CLKID_PSRAM_DIV 158
+#define CLKID_PSRAM_SEL2 159
+#define CLKID_DMC_SEL 161
+#define CLKID_DMC_DIV 162
+#define CLKID_DMC_SEL2 163
+#define NR_CLKS 165
+
+#include <dt-bindings/clock/a1-clkc.h>
+
+#endif /* __A1_H */
--
1.9.1
.