Re: [PATCH v9 08/21] iommu/io-pgtable-arm-v7s: Extend MediaTek 4GB Mode

[Will Deacon]

On Fri, Aug 16, 2019 at 03:22:20PM +0800, Yong Wu wrote:
> On Thu, 2019-08-15 at 12:50 +0100, Will Deacon wrote:
> > Ok, I think speaking to Robin helped me a bit with this...
> > 
> > On Thu, Aug 15, 2019 at 06:18:38PM +0800, Yong Wu wrote:
> > > On Thu, 2019-08-15 at 10:51 +0100, Will Deacon wrote:
> > > > On Thu, Aug 15, 2019 at 04:47:49PM +0800, Yong Wu wrote:
> > > > > On Wed, 2019-08-14 at 15:41 +0100, Will Deacon wrote:
> > > > > > On Sat, Aug 10, 2019 at 03:58:08PM +0800, Yong Wu wrote:
> > > > > > > MediaTek extend the arm v7s descriptor to support the dram over 4GB.
> > > > > > > 
> > > > > > > In the mt2712 and mt8173, it's called "4GB mode", the physical address
> > > > > > > is from 0x4000_0000 to 0x1_3fff_ffff, but from EMI point of view, it
> > > > > > > is remapped to high address from 0x1_0000_0000 to 0x1_ffff_ffff, the
> > > > > > > bit32 is always enabled. thus, in the M4U, we always enable the bit9
> > > > > > > for all PTEs which means to enable bit32 of physical address. Here is
> > > > > > > the detailed remap relationship in the "4GB mode":
> > > > > > > CPU PA         ->    HW PA
> > > > > > > 0x4000_0000          0x1_4000_0000 (Add bit32)
> > > > > > > 0x8000_0000          0x1_8000_0000 ...
> > > > > > > 0xc000_0000          0x1_c000_0000 ...
> > > > > > > 0x1_0000_0000        0x1_0000_0000 (No change)
> > 
> > [...]
> > 
> > > > > > The way I would like this quirk to work is that the io-pgtable code
> > > > > > basically sets bit 9 in the pte when bit 32 is set in the physical address,
> > > > > > and sets bit 4 in the pte when bit 33 is set in the physical address. It
> > > > > > would then do the opposite when converting a pte to a physical address.
> > > > > > 
> > > > > > That way, your driver can call the page table code directly with the high
> > > > > > addresses and we don't have to do any manual offsetting or range checking
> > > > > > in the page table code.
> > > > > 
> > > > > In this case, the mt8183 can work successfully while the "4gb
> > > > > mode"(mt8173/mt2712) can not.
> > > > > 
> > > > > In the "4gb mode", As the remap relationship above, we should always add
> > > > > bit32 in pte as we did in [2]. and need add bit32 in the
> > > > > "iova_to_phys"(Not always add.). That means the "4gb mode" has a special
> > > > > flow:
> > > > > a. Always add bit32 in paddr_to_iopte.
> > > > > b. Add bit32 only when PA < 0x40000000 in iopte_to_paddr.
> > > > 
> > > > I think this is probably at the heart of my misunderstanding. What is so
> > > > special about PAs (is this HW PA or CPU PA?) below 0x40000000? Is this RAM
> > > > or something else?
> > > 
> > > SRAM and HW register that IOMMU can not access.
> > 
> > Ok, so redrawing your table from above, I think we can say something like:
> > 
> > 
> > CPU Physical address
> > ====================
> > 
> > 0G	1G	2G	3G	4G	5G
> > |---A---|---B---|---C---|---D---|---E---|
> > +--I/O--+------------Memory-------------+
> > 
> > 
> > IOMMU output physical address
> > =============================
> > 
> > 				4G	5G	6G	7G	8G
> > 				|---E---|---B---|---C---|---D---|
> > 				+------------Memory-------------+
> > 
> > 
> > Do you agree? 
> 
> Quite right.

Woohoo! So I finally got something right about this :) I'd be up for
including the diagrams above either in the commit message or in the IOMMU
driver code, along with a comment saying that region 'A' cannot be mapped
by the IOMMU and that the page-table walker uses CPU physical addresses.

> > If so, what happens to region 'A' (the I/O region) in the
> > IOMMU output physical address space. Is it accessible?
> 
> No. IOMMU can not access region 'A' above.

Got it. Thanks.

> > Anyway, I think it's the job of the driver to convert between the two
> > address spaces, so that:
> > 
> >   - On ->map(), bit 32 of the CPU physical address is set before calling
> >     into the iopgtable code
> > 
> >   - The result from ->iova_to_phys() should be the result from the
> >     iopgtable code, but with the top bit cleared for addresses over
> >     5G.
> > 
> > This assumes that:
> > 
> >   1. We're ok setting bit 9 in the ptes mapping region 'E'.
> >   2. The IOMMU page-table walker uses CPU physical addresses
> > 
> > Are those true?
> 
> Yes. Then this patch would be close to the one[1] I sent in v8.
> 
> Do I need to split this patch into 2 ones?:

Up to you. If you want to fix the current mainline behaviour of always
setting bit 4, then that should be a separate patch at the start of the
series which can be backported to stable. Is there a reason this doesn't go
wrong in practice?

> a).the pagetable code that support 34bit PA when MTK quirk is enabled.
> It only has the symmetric code handle BIT32/BIT33. Besides, I will add
> CONFIG_PHYS_ADDR_T_64BIT in the iopte_to_addr as commented before.

Hmm. I would prefer that the iopgtable code:

	* Range checks the paddr against the oas in ->map()
	* Refuses to accept an oas > 32 in ->alloc()

Then it's up to you whether you just want to pass an oas of 34 from the
IOMMU driver.

Will