[PATCH 3.16 081/157] rt2x00: do not increment sequence number while re-transmitting

From: Ben Hutchings
Date: Sat Aug 10 2019 - 16:46:31 EST


3.16.72-rc1 review patch. If anyone has any objections, please let me know.

------------------

From: Vijayakumar Durai <vijayakumar.durai1@xxxxxxxxxx>

commit 746ba11f170603bf1eaade817553a6c2e9135bbe upstream.

Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.

This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.

Without fix retransmitted frames have wrong SN:

AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1

With the fix SN stays correctly the same:

88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C

Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@xxxxxxxxxx>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@xxxxxxxxxx>
Signed-off-by: Kalle Valo <kvalo@xxxxxxxxxxxxxx>
[bwh: Backported to 3.16: adjust filenames, context]
Signed-off-by: Ben Hutchings <ben@xxxxxxxxxxxxxxx>
---
drivers/net/wireless/rt2x00/rt2x00.h | 1 -
drivers/net/wireless/rt2x00/rt2x00mac.c | 10 ----------
drivers/net/wireless/rt2x00/rt2x00queue.c | 15 +++++++++------
3 files changed, 9 insertions(+), 17 deletions(-)

--- a/drivers/net/wireless/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/rt2x00/rt2x00.h
@@ -666,7 +666,6 @@ enum rt2x00_state_flags {
CONFIG_CHANNEL_HT40,
CONFIG_POWERSAVING,
CONFIG_HT_DISABLED,
- CONFIG_QOS_DISABLED,

/*
* Mark we currently are sequentially reading TX_STA_FIFO register
--- a/drivers/net/wireless/rt2x00/rt2x00mac.c
+++ b/drivers/net/wireless/rt2x00/rt2x00mac.c
@@ -682,19 +682,9 @@ void rt2x00mac_bss_info_changed(struct i
rt2x00dev->intf_associated--;

rt2x00leds_led_assoc(rt2x00dev, !!rt2x00dev->intf_associated);
-
- clear_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags);
}

/*
- * Check for access point which do not support 802.11e . We have to
- * generate data frames sequence number in S/W for such AP, because
- * of H/W bug.
- */
- if (changes & BSS_CHANGED_QOS && !bss_conf->qos)
- set_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags);
-
- /*
* When the erp information has changed, we should perform
* additional configuration steps. For all other changes we are done.
*/
--- a/drivers/net/wireless/rt2x00/rt2x00queue.c
+++ b/drivers/net/wireless/rt2x00/rt2x00queue.c
@@ -201,15 +201,18 @@ static void rt2x00queue_create_tx_descri
if (!test_bit(REQUIRE_SW_SEQNO, &rt2x00dev->cap_flags)) {
/*
* rt2800 has a H/W (or F/W) bug, device incorrectly increase
- * seqno on retransmited data (non-QOS) frames. To workaround
- * the problem let's generate seqno in software if QOS is
- * disabled.
+ * seqno on retransmitted data (non-QOS) and management frames.
+ * To workaround the problem let's generate seqno in software.
+ * Except for beacons which are transmitted periodically by H/W
+ * hence hardware has to assign seqno for them.
*/
- if (test_bit(CONFIG_QOS_DISABLED, &rt2x00dev->flags))
- __clear_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
- else
+ if (ieee80211_is_beacon(hdr->frame_control)) {
+ __set_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
/* H/W will generate sequence number */
return;
+ }
+
+ __clear_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
}

/*