Re: [PATCH V2 6/6] i2c: tegra: remove BUG, BUG_ON

From: Dmitry Osipenko
Date: Fri Jun 07 2019 - 15:52:20 EST


07.06.2019 22:30, Bitan Biswas ÐÐÑÐÑ:
> Remove redundant BUG_ON calls or replace with WARN_ON_ONCE
> as needed. Replace BUG() with error handling code.
> Define I2C_ERR_UNEXPECTED_STATUS for error handling.
>
> Signed-off-by: Bitan Biswas <bbiswas@xxxxxxxxxx>
> ---
> drivers/i2c/busses/i2c-tegra.c | 16 +++++++++-------
> 1 file changed, 9 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
> index 4dfb4c1..c89d0ee 100644
> --- a/drivers/i2c/busses/i2c-tegra.c
> +++ b/drivers/i2c/busses/i2c-tegra.c
> @@ -73,6 +73,7 @@
> #define I2C_ERR_NO_ACK BIT(0)
> #define I2C_ERR_ARBITRATION_LOST BIT(1)
> #define I2C_ERR_UNKNOWN_INTERRUPT BIT(2)
> +#define I2C_ERR_UNEXPECTED_STATUS BIT(3)
>
> #define PACKET_HEADER0_HEADER_SIZE_SHIFT 28
> #define PACKET_HEADER0_PACKET_ID_SHIFT 16
> @@ -515,7 +516,6 @@ static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
> * prevent overwriting past the end of buf
> */
> if (rx_fifo_avail > 0 && buf_remaining > 0) {
> - BUG_ON(buf_remaining > 3);
> val = i2c_readl(i2c_dev, I2C_RX_FIFO);
> val = cpu_to_le32(val);
> memcpy(buf, &val, buf_remaining);
> @@ -523,7 +523,6 @@ static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
> rx_fifo_avail--;
> }
>
> - BUG_ON(rx_fifo_avail > 0 && buf_remaining > 0);
> i2c_dev->msg_buf_remaining = buf_remaining;
> i2c_dev->msg_buf = buf;
>
> @@ -581,7 +580,6 @@ static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev)
> * boundary and fault.
> */
> if (tx_fifo_avail > 0 && buf_remaining > 0) {
> - BUG_ON(buf_remaining > 3);
> memcpy(&val, buf, buf_remaining);
> val = le32_to_cpu(val);
>
> @@ -847,10 +845,13 @@ static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
>
> if (!i2c_dev->is_curr_dma_xfer) {
> if (i2c_dev->msg_read && (status & I2C_INT_RX_FIFO_DATA_REQ)) {
> - if (i2c_dev->msg_buf_remaining)
> + if (i2c_dev->msg_buf_remaining) {
> tegra_i2c_empty_rx_fifo(i2c_dev);
> - else
> - BUG();
> + } else {
> + dev_err(i2c_dev->dev, "unexpected rx data request\n");
> + i2c_dev->msg_err |= I2C_ERR_UNEXPECTED_STATUS;
> + goto err;
> + }
> }
>
> if (!i2c_dev->msg_read && (status & I2C_INT_TX_FIFO_DATA_REQ)) {
> @@ -876,7 +877,8 @@ static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
> if (status & I2C_INT_PACKET_XFER_COMPLETE) {
> if (i2c_dev->is_curr_dma_xfer)
> i2c_dev->msg_buf_remaining = 0;
> - BUG_ON(i2c_dev->msg_buf_remaining);
> + if (WARN_ON_ONCE(i2c_dev->msg_buf_remaining))
> + goto err;
> complete(&i2c_dev->msg_complete);
> }
> goto done;
>

Unfortunately that's not enough because the indicator of the error is
the i2c_dev->msg_err and no error is set in yours case, hence no
hardware reset will be performed. It should be at least somewhat like this:

if (WARN_ON_ONCE(i2c_dev->msg_buf_remaining)) {
i2c_dev->msg_err |= I2C_ERR_UNKNOWN_INTERRUPT;
goto err;
}