RE: [PATCH v2 09/10] Input: elan_i2c - correct the width/size base value

[ååæ]

Hi

-----Original Message-----
From: Benjamin Tissoires [mailto:benjamin.tissoires@xxxxxxxxxx] 
Sent: Friday, May 24, 2019 3:06 PM
To: ååæ
Cc: Dmitry Torokhov; Rob Herring; Aaron Ma; Hans de Goede; open list:HID CORE LAYER; lkml; devicetree@xxxxxxxxxxxxxxx
Subject: Re: [PATCH v2 09/10] Input: elan_i2c - correct the width/size base value

On Fri, May 24, 2019 at 5:13 AM ååæ <kt.liao@xxxxxxxxxx> wrote:
>
> Hi Benjamin,
>
> Thanks so much for all you do for Elan touchpad.
>
> For the width_*, I have a question for it.
> Our antenna sensors fully occupied the whole touchpad PCB.
>
> The Gap between 2 sensors are 7.5 mil (0.19mm).
> That's why we did not minus one trace.

So, with the P52 I have:
[  +0.000009] max:    (3045,1731) drivers/input/mouse/elan_i2c_core.c:428
[  +0.000003] traces: (24,14) drivers/input/mouse/elan_i2c_core.c:429
[  +0.000002] size:   (98,55) drivers/input/mouse/elan_i2c_core.c:430
[  +0.000001] res:    (31,31) drivers/input/mouse/elan_i2c_core.c:431

calculated size (max/res): 98 x 56 mm
true size, as measured: 101 x 60 mm

I list layout information of P52 touchpad as below.
Physical size : 99 x 58 mm
Active Area size : ~ 97 * 56 mm, (boarding is 1.008mm for each side)

Sensor layout:
X Pitch : 4.0286 mm
Y Pitch : 4.0147 mm

Which gives (without the minus 1):
width_x = max_x / x_traces = 3045 / 24 = 126.875 -> 3.9885 mm width_y = max_y / y_traces = 1731 / 14 = 123.643 -> 4.0927 mm

-> this gives a total size of the touchpad of: 96 x 57 mm (width_x *
24, width_y * 14)

With the minus 1:
width_x = max_x / x_traces = 3045 / 23 = 132.391 -> 4.2707 mm width_y = max_y / y_traces = 1731 / 14 = 133.154 -> 4.2953 mm

-> this gives a total size of the touchpad of: 102 x 60 mm (width_x *
24, width_y * 14)
and considering traces-1: 98 x 56 mm

Removing 1 to the number of traces gave a squarer values in rows and columns, and this is what is done in the PS/2 driver.
Also, going back to the size of the touchpad gives a better value when removing 1 on the *traces.
So maybe when forwarding the properties we should remove one there in the PS/2 driver?

Removing 1 trace may be better for some of previous touchpad. (depending on sensor pattern)
mk_* indicate the number of trace which is touched, and it's not a precise value.
I think the usability won't change too much whether removing one trace.
PS/2 have supported plenty of touchpad. It's better to remain the same.

Thanks
KT

Cheers,
Benjamin

>
>
> Thanks
> KT
> -----Original Message-----
> From: Benjamin Tissoires [mailto:benjamin.tissoires@xxxxxxxxxx]
> Sent: Tuesday, May 21, 2019 9:27 PM
> To: Dmitry Torokhov; KT Liao; Rob Herring; Aaron Ma; Hans de Goede
> Cc: linux-input@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; 
> devicetree@xxxxxxxxxxxxxxx; Benjamin Tissoires
> Subject: [PATCH v2 09/10] Input: elan_i2c - correct the width/size 
> base value
>
> *_traces are the number of antennas. width_* is thus the space between 
> 2 antennas. Which means, we should subtract 1 to the number of 
> antennas to divide the touchpad by the number of holes between each antenna.
>
> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@xxxxxxxxxx>
>
> --
>
> new in v2
> ---
>  drivers/input/mouse/elan_i2c_core.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/input/mouse/elan_i2c_core.c
> b/drivers/input/mouse/elan_i2c_core.c
> index 6f4feedb7765..3375eaa9a72e 100644
> --- a/drivers/input/mouse/elan_i2c_core.c
> +++ b/drivers/input/mouse/elan_i2c_core.c
> @@ -398,8 +398,8 @@ static int elan_query_device_parameters(struct
> elan_tp_data *data)
>                 if (error)
>                         return error;
>         }
> -       data->width_x = data->max_x / x_traces;
> -       data->width_y = data->max_y / y_traces;
> +       data->width_x = data->max_x / (x_traces - 1);
> +       data->width_y = data->max_y / (y_traces - 1);
>
>         if (device_property_read_u32(&client->dev,
>                                      "touchscreen-x-mm", &x_mm) ||
> --
> 2.21.0
>