Re: [PATCH] arm64: dts: ulcb-kf: Add support for TI WL1837

[Eugeniu Rosca]

Hi Simon,

Do we have any chance getting this upstream? If so, would you kindly
list the acceptance criteria we have to conform to?

Many thanks.

On Thu, Apr 11, 2019 at 02:41:03PM +0200, Spyridon Papageorgiou wrote:
> This patch adds description of TI WL1837 and links interfaces
> to communicate with the IC, namely the SDIO interface to WLAN.
> 
> Signed-off-by: Spyridon Papageorgiou <spapageorgiou@xxxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/renesas/ulcb-kf.dtsi | 49 ++++++++++++++++++++++++++++++++
>  1 file changed, 49 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
> index 7a09576..27851a7 100644
> --- a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
> +++ b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
> @@ -38,6 +38,18 @@
>  		regulator-min-microvolt = <5000000>;
>  		regulator-max-microvolt = <5000000>;
>  	};
> +
> +	wlan_en: regulator-wlan_en {
> +		compatible = "regulator-fixed";
> +		regulator-name = "wlan-en-regulator";
> +
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&gpio_exp_74 4 GPIO_ACTIVE_HIGH>;
> +		startup-delay-us = <70000>;
> +		enable-active-high;
> +	};
>  };
>  
>  &can0 {
> @@ -88,6 +100,13 @@
>  			line-name = "Audio_Out_OFF";
>  		};
>  
> +		sd-wifi-mux {
> +			gpio-hog;
> +			gpios = <5 GPIO_ACTIVE_HIGH>;
> +			output-low;	/* Connect WL1837 */
> +			line-name = "SD WiFi mux";
> +		};
> +
>  		hub_pwen {
>  			gpio-hog;
>  			gpios = <6 GPIO_ACTIVE_HIGH>;
> @@ -254,6 +273,12 @@
>  		function = "scif1";
>  	};
>  
> +	sdhi3_pins: sdhi3 {
> +		groups = "sdhi3_data4", "sdhi3_ctrl";
> +		function = "sdhi3";
> +		power-source = <3300>;
> +	};
> +
>  	usb0_pins: usb0 {
>  		groups = "usb0";
>  		function = "usb0";
> @@ -273,6 +298,30 @@
>  	status = "okay";
>  };
>  
> +&sdhi3 {
> +	pinctrl-0 = <&sdhi3_pins>;
> +	pinctrl-names = "default";
> +
> +	vmmc-supply = <&wlan_en>;
> +	vqmmc-supply = <&wlan_en>;
> +	bus-width = <4>;
> +	no-1-8-v;
> +	non-removable;
> +	cap-power-off-card;
> +	keep-power-in-suspend;
> +	max-frequency = <26000000>;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	wlcore: wlcore@2 {
> +		compatible = "ti,wl1837";
> +		reg = <2>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +	};
> +};
> +
>  &usb2_phy0 {
>  	pinctrl-0 = <&usb0_pins>;
>  	pinctrl-names = "default";
> -- 
> 2.7.4
> 

-- 
Best regards,
Eugeniu.