Re: [PATCH v2] drivers: mux: Add Generic regmap bitfield-based multiplexer in mmio-mux

From: Peter Rosin
Date: Thu Feb 21 2019 - 11:06:45 EST


On 2019-02-21 15:17, Pankaj Bansal wrote:
>
>
>> -----Original Message-----
>> From: Peter Rosin [mailto:peda@xxxxxxxxxx]
>> Sent: Thursday, 21 February, 2019 07:12 PM
>> To: Pankaj Bansal <pankaj.bansal@xxxxxxx>; Leo Li <leoyang.li@xxxxxxx>
>> Cc: linux-kernel@xxxxxxxxxxxxxxx
>> Subject: Re: [PATCH v2] drivers: mux: Add Generic regmap bitfield-based
>> multiplexer in mmio-mux
>>
>> Hi!
>>
>> Much better, thanks! One nit below:
>>
>> On 2019-02-21 13:48, Pankaj Bansal wrote:
>>> Generic register bitfield-based multiplexer that controls the
>>> multiplexer producer defined under a parent node.
>>> The driver corresponding to parent node provides register read/write
>>> capabilities.
>>>
>>> Signed-off-by: Pankaj Bansal <pankaj.bansal@xxxxxxx>
>>> ---
>>>
>>> Notes:
>>> V2:
>>> - removed seperate driver regmap.c and added the regmap function in
>> mmio.c
>>> based on compatible field, the syscon or regmap function would be called
>>> - Modified the KConfig as per Peter's comments
>>>
>>> drivers/mux/Kconfig | 12 ++++++------ drivers/mux/mmio.c | 6
>>> +++++-
>>> 2 files changed, 11 insertions(+), 7 deletions(-)
>>>
>>> diff --git a/drivers/mux/Kconfig b/drivers/mux/Kconfig index
>>> 7659d6c5f718..e5c571fd232c 100644
>>> --- a/drivers/mux/Kconfig
>>> +++ b/drivers/mux/Kconfig
>>> @@ -46,14 +46,14 @@ config MUX_GPIO
>>> be called mux-gpio.
>>>
>>> config MUX_MMIO
>>> - tristate "MMIO register bitfield-controlled Multiplexer"
>>> - depends on (OF && MFD_SYSCON) || COMPILE_TEST
>>> + tristate "MMIO/Regmap register bitfield-controlled Multiplexer"
>>> + depends on OF || COMPILE_TEST
>>> help
>>> - MMIO register bitfield-controlled Multiplexer controller.
>>> + MMIO/Regmap register bitfield-controlled Multiplexer controller.
>>>
>>> - The driver builds multiplexer controllers for bitfields in a syscon
>>> - register. For N bit wide bitfields, there will be 2^N possible
>>> - multiplexer states.
>>> + The driver builds multiplexer controllers for bitfields in either
>>> + a syscon register or a driver regmap register. For N bit wide
>>> + bitfields, there will be 2^N possible multiplexer states.
>>>
>>> To compile the driver as a module, choose M here: the module will
>>> be called mux-mmio.
>>> diff --git a/drivers/mux/mmio.c b/drivers/mux/mmio.c index
>>> 935ac44aa209..37fbcde7f1fc 100644
>>> --- a/drivers/mux/mmio.c
>>> +++ b/drivers/mux/mmio.c
>>> @@ -28,6 +28,7 @@ static const struct mux_control_ops mux_mmio_ops = {
>>>
>>> static const struct of_device_id mux_mmio_dt_ids[] = {
>>> { .compatible = "mmio-mux", },
>>> + { .compatible = "reg-mux", },
>>> { /* sentinel */ }
>>> };
>>> MODULE_DEVICE_TABLE(of, mux_mmio_dt_ids); @@ -43,7 +44,10 @@
>> static
>>> int mux_mmio_probe(struct platform_device *pdev)
>>> int ret;
>>> int i;
>>>
>>> - regmap = syscon_node_to_regmap(np->parent);
>>> + if (of_device_is_compatible(np, "mmio-mux"))
>>> + regmap = syscon_node_to_regmap(np->parent);
>>> + else
>>> + regmap = dev_get_regmap(dev->parent, NULL);
>>
>> dev_get_regmap() returns NULL on failure, so I think you need something like:
>>
>> regmap = dev_get_regmap(dev->parent, NULL) ?: ERR_PTR(-
>> EINVAL);
>>
>> Or perhaps -ENODEV, -ENOTSUPP or something, not sure?
>
> How about IS_ERR_OR_NULL just below this, where right now IS_ERR is being used ?

I discarded that since you then have to specialize the error handling
to not just do "ret = PTR_ERR(regmap);"

But if you'd like to do something other than my minimal fix, then feel free
to make a proposal...

Cheers,
Peter

>
>>
>> Cheers,
>> Peter
>>
>>> if (IS_ERR(regmap)) {
>>> ret = PTR_ERR(regmap);
>>> dev_err(dev, "failed to get regmap: %d\n", ret);
>>>
>