[PATCH] regmap: irq: add an option to clear status registers on unmask

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>

Some interrupt controllers whose interrupts are acked on read will set
the status bits for masked interrupts without changing the state of
the IRQ line.

Some chips have an additional "feature" where if those set bits are
not cleared before unmasking their respective interrupts, the IRQ
line will change the state and we'll interpret this as an interrupt
although it actually fired when it was masked.

Add a new field to the irq chip struct that tells the regmap irq chip
code to always clear the status registers before actually changing the
irq mask values.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
---
Hi Mark,

there's one more problem I noticed with max77650. When a condition for
a masked interrupt is met - its status bit is set but the irq line
doesn't go low. Now if we don't clear that bit and unmask its
respective interrupt, the line will go low and we'll interpret it as
if an interrupt fired right after we enabled it.

This patch tries to address it in a generic way.

 drivers/base/regmap/regmap-irq.c | 23 +++++++++++++++++++++++
 include/linux/regmap.h           |  4 ++++
 2 files changed, 27 insertions(+)

diff --git a/drivers/base/regmap/regmap-irq.c b/drivers/base/regmap/regmap-irq.c
index 8b216b2e2c19..5a454fcd10db 100644
--- a/drivers/base/regmap/regmap-irq.c
+++ b/drivers/base/regmap/regmap-irq.c
@@ -44,6 +44,8 @@ struct regmap_irq_chip_data {
 
 	unsigned int irq_reg_stride;
 	unsigned int type_reg_stride;
+
+	bool clear_status:1;
 };
 
 static inline const
@@ -77,6 +79,7 @@ static void regmap_irq_sync_unlock(struct irq_data *data)
 	int i, ret;
 	u32 reg;
 	u32 unmask_offset;
+	u32 val;
 
 	if (d->chip->runtime_pm) {
 		ret = pm_runtime_get_sync(map->dev);
@@ -85,6 +88,20 @@ static void regmap_irq_sync_unlock(struct irq_data *data)
 				ret);
 	}
 
+	if (d->clear_status) {
+		for (i = 0; i < d->chip->num_regs; i++) {
+			reg = d->chip->status_base +
+				(i * map->reg_stride * d->irq_reg_stride);
+
+			ret = regmap_read(map, reg, &val);
+			if (ret)
+				dev_err(d->map->dev,
+					"Failed to clear the interrupt status bits\n");
+		}
+
+		d->clear_status = false;
+	}
+
 	/*
 	 * If there's been a change in the mask write it back to the
 	 * hardware.  We rely on the use of the regmap core cache to
@@ -217,6 +234,9 @@ static void regmap_irq_enable(struct irq_data *data)
 	else
 		mask = irq_data->mask;
 
+	if (d->chip->clear_on_unmask)
+		d->clear_status = true;
+
 	d->mask_buf[irq_data->reg_offset / map->reg_stride] &= ~mask;
 }
 
@@ -459,6 +479,9 @@ int regmap_add_irq_chip(struct regmap *map, int irq, int irq_flags,
 	if (chip->num_regs <= 0)
 		return -EINVAL;
 
+	if (chip->clear_on_unmask && (chip->ack_base || chip->use_ack))
+		return -EINVAL;
+
 	for (i = 0; i < chip->num_irqs; i++) {
 		if (chip->irqs[i].reg_offset % map->reg_stride)
 			return -EINVAL;
diff --git a/include/linux/regmap.h b/include/linux/regmap.h
index b7aa50cfb306..23dfacf281f8 100644
--- a/include/linux/regmap.h
+++ b/include/linux/regmap.h
@@ -1134,6 +1134,9 @@ struct regmap_irq {
  * @type_in_mask: Use the mask registers for controlling irq type. For
  *                interrupts defining type_rising/falling_mask use mask_base
  *                for edge configuration and never update bits in type_base.
+ * @clear_on_unmask: For chips with interrupts cleared on read: read the status
+ *                   registers before unmasking interrupts to clear any bits
+ *                   set when they were masked.
  * @runtime_pm:  Hold a runtime PM lock on the device when accessing it.
  *
  * @num_regs:    Number of registers in each control bank.
@@ -1173,6 +1176,7 @@ struct regmap_irq_chip {
 	bool runtime_pm:1;
 	bool type_invert:1;
 	bool type_in_mask:1;
+	bool clear_on_unmask:1;
 
 	int num_regs;
 
-- 
2.19.1