[PATCH v2 3/3] Bluetooth: hci_qca: Fix frame reassembly errors for wcn3990

[Balakrishna Godavarthi]

During initalization of wcn3990, we observed UART is reading some
stray bytes on the Rx line. This is logging Frame reassembly errors
on the serial console. This could be because of tristate of Tx line
of wcn3990 during boot up.

[  176.929612] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
[  176.945734] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
[  176.953298] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
[  177.010660] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)
[  177.067633] Bluetooth: hci_qca.c:qca_recv() hci0: Frame reassembly failed (-84)

Now we enable a flag during bootup to stop executing proto receive
function and clear it back once the initialization is done.

Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
Tested-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>
---
v2:
 * Updated commit text & comments.
v1: 
 * initial patch
---
 drivers/bluetooth/hci_qca.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index ed905ea1c58a..2f3d9e16ba5a 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -56,6 +56,7 @@
 
 /* Controller states */
 #define STATE_IN_BAND_SLEEP_ENABLED	1
+#define STATE_DISCARD_RX		2
 
 #define IBS_WAKE_RETRANS_TIMEOUT_MS	100
 #define IBS_TX_IDLE_TIMEOUT_MS		2000
@@ -511,6 +512,7 @@ static int qca_open(struct hci_uart *hu)
 		} else {
 			hu->init_speed = qcadev->init_speed;
 			hu->oper_speed = qcadev->oper_speed;
+			set_bit(STATE_DISCARD_RX, &qca->flags);
 			ret = qca_power_setup(hu, true);
 			if (ret) {
 				destroy_workqueue(qca->workqueue);
@@ -903,6 +905,13 @@ static int qca_recv(struct hci_uart *hu, const void *data, int count)
 	if (!test_bit(HCI_UART_REGISTERED, &hu->flags))
 		return -EUNATCH;
 
+	/* We discard Rx data received while device is in booting
+	 * stage, This is because of BT chip Tx line is in tristate.
+	 * Due to this we read some garbage data on UART Rx.
+	 */
+	if (test_bit(STATE_DISCARD_RX, &qca->flags))
+		return 0;
+
 	qca->rx_skb = h4_recv_buf(hu->hdev, qca->rx_skb, data, count,
 				  qca_recv_pkts, ARRAY_SIZE(qca_recv_pkts));
 	if (IS_ERR(qca->rx_skb)) {
@@ -1193,6 +1202,7 @@ static int qca_setup(struct hci_uart *hu)
 		if (ret)
 			return ret;
 
+		clear_bit(STATE_DISCARD_RX, &qca->flags);
 		ret = qca_read_soc_version(hdev, &soc_ver);
 		if (ret)
 			return ret;
@@ -1269,6 +1279,14 @@ static const struct qca_vreg_data qca_soc_data = {
 
 static void qca_power_shutdown(struct hci_uart *hu)
 {
+	struct qca_data *qca = hu->priv;
+
+	/* From this point we go into power off state,
+	 * disable IBS and discard all the queued data.
+	 */
+	clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
+	set_bit(STATE_DISCARD_RX, &qca->flags);
+	qca_flush(hu);
 	host_set_baudrate(hu, 2400);
 	qca_send_power_pulse(hu, QCA_WCN3990_POWEROFF_PULSE);
 	qca_power_setup(hu, false);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project