RE: [PATCH net-next 5/6] net/ncsi: Reset channel state in ncsi_start_dev()

[Justin.Lee1]

> On Tue, 2018-10-30 at 21:26 +0000, Justin.Lee1@xxxxxxxx wrote:
> > > +int ncsi_reset_dev(struct ncsi_dev *nd)
> > > +{
> > > +	struct ncsi_dev_priv *ndp = TO_NCSI_DEV_PRIV(nd);
> > > +	struct ncsi_channel *nc, *active;
> > > +	struct ncsi_package *np;
> > > +	unsigned long flags;
> > > +	bool enabled;
> > > +	int state;
> > > +
> > > +	active = NULL;
> > > +	NCSI_FOR_EACH_PACKAGE(ndp, np) {
> > > +		NCSI_FOR_EACH_CHANNEL(np, nc) {
> > > +			spin_lock_irqsave(&nc->lock, flags);
> > > +			enabled = nc->monitor.enabled;
> > > +			state = nc->state;
> > > +			spin_unlock_irqrestore(&nc->lock, flags);
> > > +
> > > +			if (enabled)
> > > +				ncsi_stop_channel_monitor(nc);
> > > +			if (state == NCSI_CHANNEL_ACTIVE) {
> > > +				active = nc;
> > > +				break;
> > 
> > Is the original intention to process the channel one by one?
> > If it is the case, there are two loops and we might need to use
> > "goto found" instead.
> 
> Yes we'll need to break out of the package loop here as well.
> 
> > 
> > > +			}
> > > +		}
> > > +	}
> > > +
> > 
> > found: ?
> > 
> > > +	if (!active) {
> > > +		/* Done */
> > > +		spin_lock_irqsave(&ndp->lock, flags);
> > > +		ndp->flags &= ~NCSI_DEV_RESET;
> > > +		spin_unlock_irqrestore(&ndp->lock, flags);
> > > +		return ncsi_choose_active_channel(ndp);
> > > +	}
> > > +
> > > +	spin_lock_irqsave(&ndp->lock, flags);
> > > +	ndp->flags |= NCSI_DEV_RESET;
> > > +	ndp->active_channel = active;
> > > +	ndp->active_package = active->package;
> > > +	spin_unlock_irqrestore(&ndp->lock, flags);
> > > +
> > > +	nd->state = ncsi_dev_state_suspend;
> > > +	schedule_work(&ndp->work);
> > > +	return 0;
> > > +}
> > 
> > Also similar issue in ncsi_choose_active_channel() function below.
> > 
> > > @@ -916,32 +1045,49 @@ static int ncsi_choose_active_channel(struct ncsi_dev_priv *ndp)
> > >  
> > >  			ncm = &nc->modes[NCSI_MODE_LINK];
> > >  			if (ncm->data[2] & 0x1) {
> > > -				spin_unlock_irqrestore(&nc->lock, flags);
> > >  				found = nc;
> > > -				goto out;
> > > +				with_link = true;
> > >  			}
> > >  
> > > -			spin_unlock_irqrestore(&nc->lock, flags);
> > > +			/* If multi_channel is enabled configure all valid
> > > +			 * channels whether or not they currently have link
> > > +			 * so they will have AENs enabled.
> > > +			 */
> > > +			if (with_link || np->multi_channel) {
> > 
> > I notice that there is a case that we will misconfigure the interface.
> > For example below, multi-channel is not enable for package 1.
> > But we enable the channel for ncsi2 below (package 1 channel 0) as that interface is the first
> > channel for that package with link.
> 
> I don't think I see the issue here; multi-channel is not set on package
> 1, but both channels are in the channel whitelist. Channel 0 is
> configured since it's the first found on package 1, and channel 1 is not
> since channel 0 is already found. Are you expecting something different?
>  

The setting is that multi-package is enable for both package 0 and 1.
Multi-channel is only enabled for package 0.

> > 
> > cat /sys/kernel/debug/ncsi_protocol/ncsi_device_
> > IFIDX IFNAME NAME   PID CID RX TX MP MC WP WC PC CS PS LS RU CR NQ HA
> > =====================================================================
> >   2   eth2   ncsi0  000 000 1  1  1  1  1  1  0  2  1  1  1  1  0  1
> >   2   eth2   ncsi1  000 001 1  0  1  1  1  1  0  2  1  1  1  1  0  1
> >   2   eth2   ncsi2  001 000 1  0  1  0  1  1  0  2  1  1  1  1  0  1

I was replying to the wrong old email and it might cause a bit confusion.
The first 1 meaning channel is enabled for package 1 channel 0 (ncsi2). 
For eth2, we already has ncsi0 as the active channel with TX enable.
I would think that package doesn't have the multi-channel enabled and
we should not enable the channel for ncsi2. The problem is that package 1 doesn't
enable the multi-channel and it believes it needs to enable one channel for its package 
but it doesn't aware that the other package already has one active channel.

> >   2   eth2   ncsi3  001 001 0  0  1  0  1  1  0  1  0  1  1  1  0  1
> > =====================================================================
> > MP: Multi-mode Package     WP: Whitelist Package
> > MC: Multi-mode Channel     WC: Whitelist Channel
> > PC: Primary Channel        CS: Channel State IA/A/IV 1/2/3
> > PS: Poll Status            LS: Link Status
> > RU: Running                CR: Carrier OK
> > NQ: Queue Stopped          HA: Hardware Arbitration
> > 
> > I temporally change to the following to avoid that.
> > 			if ((with_link &&
> > 			     !np->multi_channel &&
> > 			     list_empty(&ndp->channel_queue)) || np->multi_channel) {
> > 
> > > +				spin_lock_irqsave(&ndp->lock, flags);
> > > +				list_add_tail_rcu(&nc->link,
> > > +						  &ndp->channel_queue);
> > > +				spin_unlock_irqrestore(&ndp->lock, flags);
> > > +
> > > +				netdev_dbg(ndp->ndev.dev,
> > > +					   "NCSI: Channel %u added to queue (link %s)\n",
> > > +					   nc->id,
> > > +					   ncm->data[2] & 0x1 ? "up" : "down");
> > > +			}
> > > +
> > > +			spin_unlock_irqrestore(&nc->lock, cflags);
> > > +
> > > +			if (with_link && !np->multi_channel)
> > > +				break;
> > 
> > Similar issue here. As we are using break, so each package will configure one active TX.
> > 
> 
> I believe this is handled properly in ncsi_channel_is_tx() in the most
> recent revision.

I saw this issue with the last revision. I was using the wrong email to reply.

> 
> > >  		}
> > > +		if (with_link && !ndp->multi_package)
> > > +			break;
> > >  	}
> > >  
> > > -	if (!found) {
> > > +	if (list_empty(&ndp->channel_queue) && found) {
> > > +		netdev_info(ndp->ndev.dev,
> > > +			    "NCSI: No channel with link found, configuring channel %u\n",
> > > +			    found->id);
> > > +		spin_lock_irqsave(&ndp->lock, flags);
> > > +		list_add_tail_rcu(&found->link, &ndp->channel_queue);
> > > +		spin_unlock_irqrestore(&ndp->lock, flags);
> > > +	} else if (!found) {
> > >  		netdev_warn(ndp->ndev.dev,
> > > -			    "NCSI: No channel found with link\n");
> > > +			    "NCSI: No channel found to configure!\n");
> > >  		ncsi_report_link(ndp, true);
> > >  		return -ENODEV;
> > >  	}
> > 
> > Also, for deselect package handler function, do we want to set to inactive here?
> > If we just change the state, the cached data still keeps the old value. If the new 
> > ncsi_reset_dev() function is handling one by one, can we skip this part?
> 
> Technically yes we could skip the state change here since
> ncsi_reset_dev() will have already done it. However if we send a DP
> command via some other means then it is probably best to ensure we treat
> all channels on that package as inactive.

When I tested, if I didn't comment out the state change in response handler,
ncsi_reset_dev() function will not handle properly and some channels got into
invisible state and at the end we lost those selectable channels.

> 
> > 
> > static int ncsi_rsp_handler_dp(struct ncsi_request *nr)
> > {
> > 	struct ncsi_rsp_pkt *rsp;
> > 	struct ncsi_dev_priv *ndp = nr->ndp;
> > 	struct ncsi_package *np;
> > 	struct ncsi_channel *nc;
> > 	unsigned long flags;
> > 
> > 	/* Find the package */
> > 	rsp = (struct ncsi_rsp_pkt *)skb_network_header(nr->rsp);
> > 	ncsi_find_package_and_channel(ndp, rsp->rsp.common.channel,
> > 				      &np, NULL);
> > 	if (!np)
> > 		return -ENODEV;
> > 
> > 	/* Change state of all channels attached to the package */
> > 	NCSI_FOR_EACH_CHANNEL(np, nc) {
> > 		spin_lock_irqsave(&nc->lock, flags);
> > 		nc->state = NCSI_CHANNEL_INACTIVE;
> > 
> > 		spin_unlock_irqrestore(&nc->lock, flags);
> > 	}
> > 
> > 	return 0;
> > }
> > 
> >