Re: [PATCH V2 1/8] dt-bindings: mfd: document stpmic1

From: Rob Herring
Date: Tue Sep 25 2018 - 17:21:24 EST

Next message: Rob Herring: "Re: [PATCH V2 3/8] dt-bindings: regulator: document stpmic1 pmic regulators"
Previous message: Dan Murphy: "Re: [PATCH v7 3/6] dt-bindings: leds: Add bindings for lm3697 driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Fri, Sep 07, 2018 at 12:59:43PM +0000, Pascal PAILLET-LME wrote:
> From: pascal paillet <p.paillet@xxxxxx>
>
> stpmic1 is a pmic from STMicroelectronics. The stpmic1 integrates 10
> regulators and 3 switches with various capabilities.
>
> Signed-off-by: pascal paillet <p.paillet@xxxxxx>
> ---
> changes in v2:
> * the hardware component has been renamed from stpmu1 to stpmic1 !
> * replace _ with - in properties name
> * fix node names in example
> * remove regulator compatibles in example
> * add st,stpmic1.h to the patch
>
> Rob, I did not change the usage of the properties because it would lead to a lot
> of st properties; for example st,main-control-register would be replaced by:
> st,power_cycling_on_turn_off
> st,pwrctrl_enabled
> st,pwrctrl_active_high
> should I go this way ?

I guess it is fine as-is.

> Rob, I did not found the standard property for st,onkey-press-seconds = <10>;

>From input/keys.txt:

Optional properties for Keys:
- power-off-time-sec: Duration in seconds which the key should be kept
pressed for device to power off automatically. Device with key
pressed
shutdown feature can specify this property.

>
> .../devicetree/bindings/mfd/st,stpmic1.txt | 137 +++++++++++++++++++++
> include/dt-bindings/mfd/st,stpmic1.h | 46 +++++++
> 2 files changed, 183 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmic1.txt
> create mode 100644 include/dt-bindings/mfd/st,stpmic1.h
>
> diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
> new file mode 100644
> index 0000000..9f2c516
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt
> @@ -0,0 +1,137 @@
> +* STMicroelectronics STPMIC1 Power Management IC
> +
> +Required parent device properties:
> +- compatible: "st,stpmic1"
> +- reg: the I2C slave address for the stpmic1 chip
> +- interrupts-extended: interrupt lines to use: second irq is for wakeup.

Just use 'interrupts' here. Support for interrupts-extended is implied.

> +- #interrupt-cells: should be 2.
> +- interrupt-controller: describes the STPMIC1 as an interrupt
> + controller (has its own domain). interrupt number are the following:
> + /* Interrupt Register 1 (0x50 for latch) */
> + IT_SWOUT_R=0
> + IT_SWOUT_F=1
> + IT_VBUS_OTG_R=2
> + IT_VBUS_OTG_F=3
> + IT_WAKEUP_R=4
> + IT_WAKEUP_F=5
> + IT_PONKEY_R=6
> + IT_PONKEY_F=7
> + /* Interrupt Register 2 (0x51 for latch) */
> + IT_OVP_BOOST=8
> + IT_OCP_BOOST=9
> + IT_OCP_SWOUT=10
> + IT_OCP_OTG=11
> + IT_CURLIM_BUCK4=12
> + IT_CURLIM_BUCK3=13
> + IT_CURLIM_BUCK2=14
> + IT_CURLIM_BUCK1=15
> + /* Interrupt Register 3 (0x52 for latch) */
> + IT_SHORT_SWOUT=16
> + IT_SHORT_SWOTG=17
> + IT_CURLIM_LDO6=18
> + IT_CURLIM_LDO5=19
> + IT_CURLIM_LDO4=20
> + IT_CURLIM_LDO3=21
> + IT_CURLIM_LDO2=22
> + IT_CURLIM_LDO1=23
> + /* Interrupt Register 3 (0x52 for latch) */
> + IT_SWIN_R=24
> + IT_SWIN_F=25
> + IT_RESERVED_1=26
> + IT_RESERVED_2=27
> + IT_VINLOW_R=28
> + IT_VINLOW_F=29
> + IT_TWARN_R=30
> + IT_TWARN_F=31
> +
> +Optional parent device properties:
> +- st,main-control-register:
> + -bit 1: Power cycling will be performed on turn OFF condition
> + -bit 2: PWRCTRL is functional
> + -bit 3: PWRCTRL active high
> +- st,pads-pull-register:
> + -bit 1: WAKEUP pull down is not active
> + -bit 2: PWRCTRL pull up is active
> + -bit 3: PWRCTRL pull down is active
> + -bit 4: WAKEUP detector is disabled
> +- st,vin-control-register:
> + -bit 0: VINLOW monitoring is enabled
> + -bit [1...3]: VINLOW rising threshold
> + 000 VINOK_f + 50mV
> + 001 VINOK_f + 100mV
> + 010 VINOK_f + 150mV
> + 011 VINOK_f + 200mV
> + 100 VINOK_f + 250mV
> + 101 VINOK_f + 300mV
> + 110 VINOK_f + 350mV
> + 111 VINOK_f + 400mV
> + -bit [4...5]: VINLOW hyst
> + 00 100mV
> + 01 200mV
> + 10 300mV
> + 11 400mV
> + -bit 6: SW_OUT detector is disabled
> + -bit 7: SW_IN detector is enabled.
> +- st,usb-control-register:
> + -bit 3: SW_OUT current limit
> + 0: 600mA
> + 1: 1.1A
> + -bit 4: VBUS_OTG discharge is enabled
> + -bit 5: SW_OUT discharge is enabled
> + -bit 6: VBUS_OTG detection is enabled
> + -bit 7: BOOST_OVP is disabled
> +
> +
> +stpmic1 consists is a varied group of sub-devices:
> +
> +Device Description
> +------ ------------
> +st,stpmic1-onkey : On key
> +st,stpmic1-regulators : Regulators
> +st,stpmic1-wdt : Watchdog
> +
> +each sub-device bindings is be described in associated driver
> +documentation section.
> +
> +Example:
> +
> +pmic: stpmic1@33 {

pmic@33

> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts = <0 2>;
> + interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_NONE>,
> + <&exti 55 1>;
> + st,version_status = <0x10>;
> + st,main-control-register=<0x0c>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupt-parent = <&pmic>;
> + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + st,onkey-pwroff-enabled;
> + st,onkey-long-press-seconds = <10>;
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + };
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> +
> + vdd_core: buck1 {
> + regulator-name = "vdd_core";
> + regulator-boot-on;
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1200000>;
> + };
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-pull-down;
> + };
> + };
> diff --git a/include/dt-bindings/mfd/st,stpmic1.h b/include/dt-bindings/mfd/st,stpmic1.h
> new file mode 100644
> index 0000000..e32ac8f
> --- /dev/null
> +++ b/include/dt-bindings/mfd/st,stpmic1.h
> @@ -0,0 +1,46 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
> + * Author: Philippe Peurichard <philippe.peurichard@xxxxxx>,
> + * Pascal Paillet <p.paillet@xxxxxx> for STMicroelectronics.
> + */
> +
> +#ifndef __DT_BINDINGS_STPMIC1_H__
> +#define __DT_BINDINGS_STPMIC1_H__
> +
> +/* IRQ definitions */
> +#define IT_PONKEY_F 0
> +#define IT_PONKEY_R 1
> +#define IT_WAKEUP_F 2
> +#define IT_WAKEUP_R 3
> +#define IT_VBUS_OTG_F 4
> +#define IT_VBUS_OTG_R 5
> +#define IT_SWOUT_F 6
> +#define IT_SWOUT_R 7
> +
> +#define IT_CURLIM_BUCK1 8
> +#define IT_CURLIM_BUCK2 9
> +#define IT_CURLIM_BUCK3 10
> +#define IT_CURLIM_BUCK4 11
> +#define IT_OCP_OTG 12
> +#define IT_OCP_SWOUT 13
> +#define IT_OCP_BOOST 14
> +#define IT_OVP_BOOST 15
> +
> +#define IT_CURLIM_LDO1 16
> +#define IT_CURLIM_LDO2 17
> +#define IT_CURLIM_LDO3 18
> +#define IT_CURLIM_LDO4 19
> +#define IT_CURLIM_LDO5 20
> +#define IT_CURLIM_LDO6 21
> +#define IT_SHORT_SWOTG 22
> +#define IT_SHORT_SWOUT 23
> +
> +#define IT_TWARN_F 24
> +#define IT_TWARN_R 25
> +#define IT_VINLOW_F 26
> +#define IT_VINLOW_R 27
> +#define IT_SWIN_F 30
> +#define IT_SWIN_R 31
> +
> +#endif /* __DT_BINDINGS_STPMIC1_H__ */
> --
> 1.9.1

Next message: Rob Herring: "Re: [PATCH V2 3/8] dt-bindings: regulator: document stpmic1 pmic regulators"
Previous message: Dan Murphy: "Re: [PATCH v7 3/6] dt-bindings: leds: Add bindings for lm3697 driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]