[PATCH v3 0/4] Add QCOM graphics clock controller driver for SDM845

From: Amit Nischal
Date: Mon Aug 13 2018 - 02:33:32 EST


Changes in v3:
* Modified the determine_rate() op to use the min/max rate range
to round the requested rate within the set_rate range. With this,
requested set rate will always stay within the limits.

Changes in v2:
Addressed review comments given by Stephen: https://lkml.org/lkml/2018/6/6/294
* Introduce clk_rcg2_gfx3d_determine_rate ops to return the best parent
as 'gpucc_pll0_even' and best parent rate as twice of the requested rate
always. This will eliminate the need of frequency table as source and
div-2 are fixed for gfx3d_clk_src.
Also modified the clk_rcg2_set_rate ops to configure the fixed source and
div.
* Add support to check if requested rate falls within allowed set_rate range.
This will not let the source gpucc_pll0 to go out of the supported range
and also client can request the rate within the range.
* Fixed comment text in probe function and added module description for GPUCC
driver.

The graphics clock driver depends upon the below change.
https://lkml.org/lkml/2018/6/23/108

Changes in v1:
This patch series adds support for graphics clock controller for SDM845.
Below is the brief description for each change:

1. For some of the GDSCs, there is requirement to enable/disable the
few clocks before turning on/off the gdsc power domain. This patch
will add support to enable/disable the clock associated with the
gdsc along with power domain on/off callbacks.

2. To turn on the gpu_gx_gdsc, there is a hardware requirement to
turn on the root clock (GFX3D RCG) first which would be the turn
on signal for the gdsc along with the SW_COLLAPSE. As per the
current implementation of clk_rcg2_shared_ops, it clears the
root_enable bit in the enable() clock ops. But due to the above
said requirement for GFX3D shared RCG, root_enable bit would be
already set by gdsc driver and rcg2_shared_ops should not clear
the root unless the disable() is called.

This patch add support for the same by reusing the existing
clk_rcg2_shared_ops and deriving "clk_rcg2_gfx3d_ops" clk_ops
for GFX3D clock to take care of the root set/clear requirement.

3. Add device tree bindings for graphics clock controller for SDM845.

4. Add graphics clock controller (GPUCC) driver for SDM845.

[v1] : https://lore.kernel.org/patchwork/project/lkml/list/?series=348697
[v2] : https://lore.kernel.org/patchwork/project/lkml/list/?series=359012

Amit Nischal (4):
clk: qcom: gdsc: Add support to enable/disable the clocks with GDSC
clk: qcom: Add clk_rcg2_gfx3d_ops for SDM845
dt-bindings: clock: Introduce QCOM Graphics clock bindings
clk: qcom: Add graphics clock controller driver for SDM845

.../devicetree/bindings/clock/qcom,gpucc.txt | 18 +
drivers/clk/qcom/Kconfig | 9 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-rcg.h | 1 +
drivers/clk/qcom/clk-rcg2.c | 86 +++-
drivers/clk/qcom/gdsc.c | 44 +++
drivers/clk/qcom/gdsc.h | 5 +
drivers/clk/qcom/gpucc-sdm845.c | 438 +++++++++++++++++++++
include/dt-bindings/clock/qcom,gpucc-sdm845.h | 38 ++
9 files changed, 638 insertions(+), 2 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,gpucc.txt
create mode 100644 drivers/clk/qcom/gpucc-sdm845.c
create mode 100644 include/dt-bindings/clock/qcom,gpucc-sdm845.h

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation