[PATCH v6 5/7] dt-bindings: Add Tegra PMC pad configuration bindings

From: Aapo Vienamo
Date: Mon Jul 30 2018 - 10:02:03 EST


Document the PMC pinctrl bindings for pad power state and signaling
voltage configuration. Both nvidia,tegra186-pmc.txt and
nvidia,tegra20-pmc.txt are modified as they both cover SoC generations
for which these bindings apply.

Add a header defining Tegra PMC pad voltage configurations.

Signed-off-by: Aapo Vienamo <avienamo@xxxxxxxxxx>
Acked-by: Jon Hunter <jonathanh@xxxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
---
.../bindings/arm/tegra/nvidia,tegra186-pmc.txt | 92 ++++++++++++++++++
.../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 103 +++++++++++++++++++++
include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h | 18 ++++
3 files changed, 213 insertions(+)
create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h

diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
index 5a3bf7c..d7fed4d 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
@@ -34,3 +34,95 @@ Board DTS:
pmc@c360000 {
nvidia,invert-interrupt;
};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+Pad configurations are described is with pin configuration nodes which
+are placed under the pmc node and they are referred to by the pinctrl
+client properties. For more information see
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+
+Following pads are present on Tegra186:
+csia csib dsi mipi-bias
+pex-clk-bias pex-clk3 pex-clk2 pex-clk1
+usb0 usb1 usb2 usb-bias
+uart audio hsic dbg
+hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv
+sdmmc4 cam dsib dsic
+dsid csic csid csie
+dsif spi ufs dmic-hv
+edp sdmmc1-hv sdmmc3-hv conn
+audio-hv ao-hv
+
+Required pin configuration properties:
+ - pins: Must contain name of the pad(s) to be configured.
+
+Optional pin configuration properties:
+ - low-power-enable: Configure the pad into power down mode
+ - low-power-disable: Configure the pad into active mode
+ - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
+ TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+ The values are defined in
+ include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the above pads except
+ for ao-hv. Following pads have software configurable signaling
+ voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
+ ao-hv.
+
+Pad configuration state example:
+ pmc: pmc@7000e400 {
+ compatible = "nvidia,tegra186-pmc";
+ reg = <0 0x0c360000 0 0x10000>,
+ <0 0x0c370000 0 0x10000>,
+ <0 0x0c380000 0 0x10000>,
+ <0 0x0c390000 0 0x10000>;
+ reg-names = "pmc", "wake", "aotag", "scratch";
+
+ ...
+
+ sdmmc1_3v3: sdmmc1-3v3 {
+ pins = "sdmmc1-hv";
+ power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+ };
+
+ sdmmc1_1v8: sdmmc1-1v8 {
+ pins = "sdmmc1-hv";
+ power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+ };
+
+ hdmi_off: hdmi-off {
+ pins = "hdmi";
+ low-power-enable;
+ }
+
+ hdmi_on: hdmi-on {
+ pins = "hdmi";
+ low-power-disable;
+ }
+ };
+
+Pinctrl client example:
+ sdmmc1: sdhci@3400000 {
+ ...
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-0 = <&sdmmc1_3v3>;
+ pinctrl-1 = <&sdmmc1_1v8>;
+ };
+
+ ...
+
+ sor0: sor@15540000 {
+ ...
+ pinctrl-0 = <&hdmi_off>;
+ pinctrl-1 = <&hdmi_on>;
+ pinctrl-names = "hdmi-on", "hdmi-off";
+ };
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
index a74b37b..5363b90 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -195,3 +195,106 @@ Example:
power-domains = <&pd_audio>;
...
};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+The pad configuration state nodes are placed under the pmc node and they
+are referred to by the pinctrl client properties. For more information
+see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+The pad name should be used as the value of the pins property in pin
+configuration nodes.
+
+Following pads are present on Tegra124 and Tegra132:
+audio bb cam comp
+csia csb cse dsi
+dsib dsic dsid hdmi
+hsic hv lvds mipi-bias
+nand pex-bias pex-clk1 pex-clk2
+pex-cntrl sdmmc1 sdmmc3 sdmmc4
+sys_ddc uart usb0 usb1
+usb2 usb_bias
+
+Following pads are present on Tegra210:
+audio audio-hv cam csia
+csib csic csid csie
+csif dbg debug-nonao dmic
+dp dsi dsib dsic
+dsid emmc emmc2 gpio
+hdmi hsic lvds mipi-bias
+pex-bias pex-clk1 pex-clk2 pex-cntrl
+sdmmc1 sdmmc3 spi spi-hv
+uart usb0 usb1 usb2
+usb3 usb-bias
+
+Required pin configuration properties:
+ - pins: Must contain name of the pad(s) to be configured.
+
+Optional pin configuration properties:
+ - low-power-enable: Configure the pad into power down mode
+ - low-power-disable: Configure the pad into active mode
+ - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8
+ or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+ The values are defined in
+ include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the Tegra124 and
+ Tegra132 pads. None of the Tegra124 or Tegra132 pads support
+ signaling voltage switching.
+
+Note: All of the listed Tegra210 pads except pex-cntrl support power
+ state configuration. Signaling voltage switching is supported on
+ following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio,
+ pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart.
+
+Pad configuration state example:
+ pmc: pmc@7000e400 {
+ compatible = "nvidia,tegra210-pmc";
+ reg = <0x0 0x7000e400 0x0 0x400>;
+ clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
+ clock-names = "pclk", "clk32k_in";
+
+ ...
+
+ sdmmc1_3v3: sdmmc1-3v3 {
+ pins = "sdmmc1";
+ power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+ };
+
+ sdmmc1_1v8: sdmmc1-1v8 {
+ pins = "sdmmc1";
+ power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+ };
+
+ hdmi_off: hdmi-off {
+ pins = "hdmi";
+ low-power-enable;
+ }
+
+ hdmi_on: hdmi-on {
+ pins = "hdmi";
+ low-power-disable;
+ }
+ };
+
+Pinctrl client example:
+ sdmmc1: sdhci@700b0000 {
+ ...
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-0 = <&sdmmc1_3v3>;
+ pinctrl-1 = <&sdmmc1_1v8>;
+ };
+ ...
+ sor@54540000 {
+ ...
+ pinctrl-0 = <&hdmi_off>;
+ pinctrl-1 = <&hdmi_on>;
+ pinctrl-names = "hdmi-on", "hdmi-off";
+ };
diff --git a/include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h b/include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
new file mode 100644
index 0000000..20f4340
--- /dev/null
+++ b/include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * pinctrl-tegra-io-pad.h: Tegra I/O pad source voltage configuration constants
+ * pinctrl bindings.
+ *
+ * Copyright (c) 2018, NVIDIA CORPORATION. All rights reserved.
+ *
+ * Author: Aapo Vienamo <avienamo@xxxxxxxxxx>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H
+#define _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H
+
+/* Voltage levels of the I/O pad's source rail */
+#define TEGRA_IO_PAD_VOLTAGE_1V8 0
+#define TEGRA_IO_PAD_VOLTAGE_3V3 1
+
+#endif
--
2.7.4