[PATCH v5 8/8] Documentation/ABI: Add documentation mlxreg-io sysfs interfaces

From: Vadim Pasternak
Date: Tue Jun 05 2018 - 07:03:11 EST


Add documentation for mlxreg-io platform driver sysfs interfaces to allow
user space access for system resets control, reset causes monitoring,
programmable devices version reading and device selection control.

Signed-off-by: Vadim Pasternak <vadimp@xxxxxxxxxxxx>
---
v4:
Comments pointed out by Greg:
Add Documentation/ABI/ entries for the new sysfs files.
v4-v5:
Comments pointed out by Darren:
- Rename cause to reset.
- Extend explanation in doc file.
Changes added by Vadim:
- Add two new attributes.
- Re-arrange in alphabetic order after changes.
- Change date from May to June.
---
Documentation/ABI/stable/sysfs-driver-mlxreg-io | 77 +++++++++++++++++++++++++
1 file changed, 77 insertions(+)
create mode 100644 Documentation/ABI/stable/sysfs-driver-mlxreg-io

diff --git a/Documentation/ABI/stable/sysfs-driver-mlxreg-io b/Documentation/ABI/stable/sysfs-driver-mlxreg-io
new file mode 100644
index 0000000..7913a95
--- /dev/null
+++ b/Documentation/ABI/stable/sysfs-driver-mlxreg-io
@@ -0,0 +1,77 @@
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/
+ asic_health
+
+Date: June 2018
+KernelVersion: 4.18
+Contact: Vadim Pasternak <vadimpmellanox.com>
+Description: This file shows ASIC health status. The possible values are:
+ 0 - health failed, 2 - health OK, 3 - ASIC in booting state.
+
+ The files are read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/
+ cpld1_version
+ cpld2_version
+
+Date: June 2018
+KernelVersion: 4.18
+Contact: Vadim Pasternak <vadimpmellanox.com>
+Description: These files show with which CPLD versions have been burned
+ on carrier and switch boards.
+
+ The files are read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/select_iio
+Date: June 2018
+KernelVersion: 4.18
+Contact: Vadim Pasternak <vadimpmellanox.com>
+Description: This file allows iio devices selection.
+
+ Attribute select_iio can be written with 0 or with 1. It
+ selects which one of iio devices can be accessed.
+
+ The file is read/write.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu1_on
+ /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu2_on
+ /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_cycle
+ /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_down
+Date: June 2018
+KernelVersion: 4.18
+Contact: Vadim Pasternak <vadimpmellanox.com>
+Description: These files allow asserting system power cycling, switching
+ power supply units on and off and system's main power domain
+ shutdown.
+ Expected behavior:
+ When pwr_cycle is written 1: auxiliary power domain will go
+ down and after short period (about 1 second) up.
+ When psu1_on or psu2_on is written 1, related unit will be
+ disconnected from the power source, when written 0 - connected.
+ If both are written 1 - power supplies main power domain will
+ go down.
+ When pwr_down is written 1, system's main power domain will go
+ down.
+
+ The files are write only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/
+ reset_aux_pwr_or_ref
+ reset_asic_thermal
+ reset_hotswap_or_wd
+ reset_fw_reset
+ reset_long_pb
+ reset_main_pwr_fail
+ reset_short_pb
+ reset_sw_reset
+Date: June 2018
+KernelVersion: 4.18
+Contact: Vadim Pasternak <vadimpmellanox.com>
+Description: These files show the system reset cause, as following: power
+ auxiliary outage or power refresh, ASIC thermal shutdown,
+ hotswap or watchdog, firmware reset, long press power button,
+ short press power button, software reset. Value 1 in file means
+ this is reset cause, 0 - otherwise. Only one of the above
+ causes could be 1 at the same time, representing only last
+ reset cause.
+
+ The files are read only.
--
2.1.4