Re: [PATCH v3 15/16] mtd: rawnand: qcom: helper function for raw read

From: Abhishek Sahu
Date: Mon May 28 2018 - 03:34:54 EST


On 2018-05-27 19:23, Miquel Raynal wrote:
Hi Abhishek,

On Fri, 25 May 2018 17:51:43 +0530, Abhishek Sahu
<absahu@xxxxxxxxxxxxxx> wrote:

This patch does minor code reorganization for raw reads.
Currently the raw read is required for complete page but for
subsequent patches related with erased codeword bit flips
detection, only few CW should be read. So, this patch adds
helper function and introduces the read CW bitmask which
specifies which CW reads are required in complete page.

Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
---
* Changes from v2:
NONE

* Changes from v1:
1. Included more detail in function comment

drivers/mtd/nand/raw/qcom_nandc.c | 197 ++++++++++++++++++++++++--------------
1 file changed, 123 insertions(+), 74 deletions(-)

diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index 87f900e..34143a4 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -1588,6 +1588,127 @@ static int check_flash_errors(struct qcom_nand_host *host, int cw_cnt)
}

/*
+ * Helper to perform the page raw read operation. The read_cw_mask will be
+ * used to specify the codewords (CW) for which the data should be read. The
+ * single page contains multiple CW.
+ *
+ * Normally other NAND controllers store the data in main area and
+ * ecc bytes in OOB area. So, if page size is 2048+64 then 2048
+ * data bytes will go in main area followed by ECC bytes. The QCOM NAND
+ * controller follows different layout in which the data+OOB is internally
+ * divided in 528/532 bytes CW and each CW contains 516 bytes followed by
+ * ECC parity bytes for that CW. By this, 4 available OOB bytes per CW
+ * will also be protected with ECC.
+ *
+ * For each CW read, following are the 2 steps:
+ * 1. Read the codeword bytes from NAND chip to NAND controller internal HW
+ * buffer.
+ * 2. Copy all these bytes from this HW buffer to actual buffer.
+ *
+ * Sometime, only few CW data is required in complete page. The read_cw_mask
+ * specifies which CW in a page needs to be read. Start address will be
+ * determined with this CW mask to skip unnecessary data copy from NAND
+ * flash device. Then, actual data copy from NAND controller HW internal buffer
+ * to data buffer will be done only for the CWs, which have the mask set.
+ */
+static int
+nandc_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ u8 *data_buf, u8 *oob_buf,
+ int page, unsigned long read_cw_mask)

Please prefix the helper with "qcom_nandc"


Sure Miquel.
I will update that.

+{
+ struct qcom_nand_host *host = to_qcom_nand_host(chip);
+ struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ int i, ret;
+ int read_loc, start_step, last_step;
+
+ nand_read_page_op(chip, page, 0, NULL, 0);
+
+ host->use_ecc = false;
+ start_step = ffs(read_cw_mask) - 1;
+ last_step = fls(read_cw_mask);
+
+ clear_bam_transaction(nandc);
+ set_address(host, host->cw_size * start_step, page);
+ update_rw_regs(host, last_step - start_step, true);
+ config_nand_page_read(nandc);
+
+ for (i = start_step; i < last_step; i++) {

This comment applies for both patches 15 and 16:

I would really prefer having a qcom_nandc_read_cw_raw() that reads only
one CW. From qcom_nandc_read_page_raw() you would loop over all the CW
calling qcom_nandc_read_cw_raw() helper (it's raw reads, we don't care
about performances)

Doing that way will degrade performances hugely.

Currently once we formed the descriptor, the DMA will take care
of complete page data transfer from NAND device to buffer and will
generate single interrupt.

Now it will form one CW descriptor and wait for it to be finished.
In background, the data transfer from NAND device will be also
split and for every CW, it will give the PAGE_READ command again,
which is again time consuming.

Data transfer degradation is ok but it will increase CPU time
and number of interrupts which will impact other peripherals
performance that time.

Most of the NAND parts has 4K page size i.e 8 CWs.

and from ->read_page_raw() you would check
CW with uncorrectable errors for being blank with that helper. You
would avoid the not-so-nice logic where you read all the CW between the
first bad one and the last bad one.


The reading b/w first CW and last CW is only from NAND device to NAND
HW buffers. The NAND controller has 2 HW buffers which is used to
optimize the traffic throughput between the NAND device and
system memory,in both directions. Each buffer is 544B in size: 512B
for data + 32B spare bytes. Throughput optimization is achieved by
executing internal data transfers (i.e. between NANDc buffers and
system memory) simultaneously with NAND device operations.

Making separate function won't help in improving performance for
this case either since once every thing is set for reading page
(descriptor formation, issue the PAGE_READ, Data transfer from
Flash array to data register in NAND device), the read time from
device to NAND HW buffer is very less. Again, we did optimization
in which the copying from NAND HW buffer to actual buffer is being
done only for those CW's only.

Again, in this case CPU time will be more.

Thanks,
Abhishek