[PATCH] arm64: dts: hikey: Fix eMMC corruption regression

[John Stultz]

This patch is a partial revert of commit
abd7d0972a19 ("arm64: dts: hikey: Enable HS200 mode on eMMC")

which has been causing eMMC corruption on my HiKey board.

Symptoms usually looked like:

mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
...
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc0: new HS200 MMC card at address 0001
...
dwmmc_k3 f723d000.dwmmc0: Unexpected command timeout, state 3
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
print_req_error: I/O error, dev mmcblk0, sector 8810504
Aborting journal on device mmcblk0p10-8.
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
EXT4-fs error (device mmcblk0p10): ext4_journal_check_start:61: Detected aborted journal
EXT4-fs (mmcblk0p10): Remounting filesystem read-only

And quite often this would result in a disk that wouldn't properly
boot even with older kernels.

It seems the max-frequency property added by the above patch is
causing the problem, so remove it.

Cc: Ryan Grachek <ryan@xxxxxxxxx>
Cc: Wei Xu <xuwei5@xxxxxxxxxxxxx>
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Cc: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
Cc: YongQin Liu <yongqin.liu@xxxxxxxxxx>
Cc: Leo Yan <leo.yan@xxxxxxxxxx>
Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx>
---
 arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 724a0d3..edb4ee0 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -299,7 +299,6 @@
 		/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
 
 		dwmmc_0: dwmmc0@f723d000 {
-			max-frequency = <150000000>;
 			cap-mmc-highspeed;
 			mmc-hs200-1_8v;
 			non-removable;
-- 
2.7.4