Re: [RFC 5/6] dmaengine: xilinx_dma: Program interrupt delay timeout

[Vinod Koul]

On Mon, Apr 02, 2018 at 04:09:05PM +0530, Radhey Shyam Pandey wrote:
> Program IRQDelay for AXI DMA. The interrupt timeout mechanism causes
> the DMA engine to generate an interrupt after the delay time period
> has expired. It enables dmaengine to respond in real-time even though
> interrupt coalescing is configured.

again you are doing this only for axieth_connected, why is that?

> 
> Signed-off-by: Radhey Shyam Pandey <radheys@xxxxxxxxxx>
> ---
>  drivers/dma/xilinx/xilinx_dma.c |   16 ++++++++++++++--
>  1 files changed, 14 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
> index 518465e..ab8f1b0 100644
> --- a/drivers/dma/xilinx/xilinx_dma.c
> +++ b/drivers/dma/xilinx/xilinx_dma.c
> @@ -161,8 +161,12 @@
>  /* AXI DMA Specific Masks/Bit fields */
>  #define XILINX_DMA_MAX_TRANS_LEN	GENMASK(22, 0)
>  #define XILINX_DMA_CR_COALESCE_MAX	GENMASK(23, 16)
> +#define XILINX_DMA_CR_DELAY_MAX		GENMASK(31, 24)
>  #define XILINX_DMA_CR_CYCLIC_BD_EN_MASK	BIT(4)
>  #define XILINX_DMA_CR_COALESCE_SHIFT	16
> +#define XILINX_DMA_CR_DELAY_SHIFT	24
> +#define XILINX_DMA_CR_WAITBOUND_DFT	254
> +
>  #define XILINX_DMA_BD_SOP		BIT(27)
>  #define XILINX_DMA_BD_EOP		BIT(26)
>  #define XILINX_DMA_COALESCE_MAX		255
> @@ -1294,6 +1298,12 @@ static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
>  		reg &= ~XILINX_DMA_CR_COALESCE_MAX;
>  		reg |= chan->desc_pendingcount <<
>  				  XILINX_DMA_CR_COALESCE_SHIFT;
> +
> +		if (chan->xdev->has_axieth_connected) {
> +			reg  &= ~XILINX_DMA_CR_DELAY_MAX;
> +			reg  |= XILINX_DMA_CR_WAITBOUND_DFT <<
> +					XILINX_DMA_CR_DELAY_SHIFT;
> +		}
>  		dma_ctrl_write(chan, XILINX_DMA_REG_DMACR, reg);
>  	}
>  
> @@ -1508,7 +1518,8 @@ static irqreturn_t xilinx_dma_irq_handler(int irq, void *data)
>  		}
>  	}
>  
> -	if (status & XILINX_DMA_DMASR_DLY_CNT_IRQ) {
> +	if (!chan->xdev->has_axieth_connected && (status &
> +			XILINX_DMA_DMASR_DLY_CNT_IRQ)) {
>  		/*
>  		 * Device takes too long to do the transfer when user requires
>  		 * responsiveness.
> @@ -1516,7 +1527,8 @@ static irqreturn_t xilinx_dma_irq_handler(int irq, void *data)
>  		dev_dbg(chan->dev, "Inter-packet latency too long\n");
>  	}
>  
> -	if (status & XILINX_DMA_DMASR_FRM_CNT_IRQ) {
> +	if (status & (XILINX_DMA_DMASR_FRM_CNT_IRQ |
> +		      XILINX_DMA_DMASR_DLY_CNT_IRQ)) {
>  		spin_lock(&chan->lock);
>  		xilinx_dma_complete_descriptor(chan);
>  		chan->idle = true;
> -- 
> 1.7.1
> 

-- 
~Vinod