[PATCH v2 2/9] Staging: iio: accel: adis16201: Remove unnecessary comments

From: Himanshu Jha
Date: Fri Mar 16 2018 - 16:09:15 EST


Remove few unnecessary comments since the macro definitions clearly
justify their purpose.

Signed-off-by: Himanshu Jha <himanshujha199640@xxxxxxxxx>
---
v2:
-reodered patch series.

drivers/staging/iio/accel/adis16201.c | 36 -----------------------------------
1 file changed, 36 deletions(-)

diff --git a/drivers/staging/iio/accel/adis16201.c b/drivers/staging/iio/accel/adis16201.c
index 767ebf0..6c06c0d 100644
--- a/drivers/staging/iio/accel/adis16201.c
+++ b/drivers/staging/iio/accel/adis16201.c
@@ -22,96 +22,66 @@

#define ADIS16201_STARTUP_DELAY_MS 220

-/* Flash memory write count */
#define ADIS16201_FLASH_CNT 0x00

-/* Output, power supply */
#define ADIS16201_SUPPLY_OUT 0x02

-/* Output, x-axis accelerometer */
#define ADIS16201_XACCL_OUT 0x04

-/* Output, y-axis accelerometer */
#define ADIS16201_YACCL_OUT 0x06

-/* Output, auxiliary ADC input */
#define ADIS16201_AUX_ADC 0x08

-/* Output, temperature */
#define ADIS16201_TEMP_OUT 0x0A

-/* Output, x-axis inclination */
#define ADIS16201_XINCL_OUT 0x0C

-/* Output, y-axis inclination */
#define ADIS16201_YINCL_OUT 0x0E

-/* Calibration, x-axis acceleration offset */
#define ADIS16201_XACCL_OFFS 0x10

-/* Calibration, y-axis acceleration offset */
#define ADIS16201_YACCL_OFFS 0x12

-/* x-axis acceleration scale factor */
#define ADIS16201_XACCL_SCALE 0x14

-/* y-axis acceleration scale factor */
#define ADIS16201_YACCL_SCALE 0x16

-/* Calibration, x-axis inclination offset */
#define ADIS16201_XINCL_OFFS 0x18

-/* Calibration, y-axis inclination offset */
#define ADIS16201_YINCL_OFFS 0x1A

-/* x-axis inclination scale factor */
#define ADIS16201_XINCL_SCALE 0x1C

-/* y-axis inclination scale factor */
#define ADIS16201_YINCL_SCALE 0x1E

-/* Alarm 1 amplitude threshold */
#define ADIS16201_ALM_MAG1 0x20

-/* Alarm 2 amplitude threshold */
#define ADIS16201_ALM_MAG2 0x22

-/* Alarm 1, sample period */
#define ADIS16201_ALM_SMPL1 0x24

-/* Alarm 2, sample period */
#define ADIS16201_ALM_SMPL2 0x26

-/* Alarm control */
#define ADIS16201_ALM_CTRL 0x28

-/* Auxiliary DAC data */
#define ADIS16201_AUX_DAC 0x30

-/* General-purpose digital input/output control */
#define ADIS16201_GPIO_CTRL 0x32

-/* Miscellaneous control */
#define ADIS16201_MSC_CTRL 0x34

-/* Internal sample period (rate) control */
#define ADIS16201_SMPL_PRD 0x36

/* Operation, filter configuration */
#define ADIS16201_AVG_CNT 0x38

-/* Operation, sleep mode control */
#define ADIS16201_SLP_CNT 0x3A

-/* Diagnostics, system status register */
#define ADIS16201_DIAG_STAT 0x3C

-/* Operation, system command register */
#define ADIS16201_GLOB_CMD 0x3E

-/* MSC_CTRL */

-/* Self-test enable */
#define ADIS16201_MSC_CTRL_SELF_TEST_EN BIT(8)

/* Data-ready enable: 1 = enabled, 0 = disabled */
@@ -123,18 +93,13 @@
/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1 BIT(0)

-/* DIAG_STAT */

-/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
#define ADIS16201_DIAG_STAT_ALARM2 BIT(9)

-/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
#define ADIS16201_DIAG_STAT_ALARM1 BIT(8)

-/* SPI communications failure */
#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT 3

-/* Flash update failure */
#define ADIS16201_DIAG_STAT_FLASH_UPT_FAIL_BIT 2

/* Power supply above 3.625 V */
@@ -143,7 +108,6 @@
/* Power supply below 3.15 V */
#define ADIS16201_DIAG_STAT_POWER_LOW_BIT 0

-/* GLOB_CMD */

#define ADIS16201_GLOB_CMD_SW_RESET BIT(7)
#define ADIS16201_GLOB_CMD_FACTORY_RESET BIT(1)
--
2.7.4