[PATCH v2] zswap: Zero-filled pages handling

From: Srividya Desireddy
Date: Wed Aug 16 2017 - 13:20:16 EST



On Thu, Jul 6, 2017 at 3:32 PM, Dan Streetman wrote:
> On Thu, Jul 6, 2017 at 5:29 AM, Srividya Desireddy
> wrote:
>> On Wed, Jul 6, 2017 at 10:49 AM, Sergey Senozhatsky wrote:
>>> On (07/02/17 20:28), Seth Jennings wrote:
>>>> On Sun, Jul 2, 2017 at 9:19 AM, Srividya Desireddy
>>>> > Zswap is a cache which compresses the pages that are being swapped out
>>>> > and stores them into a dynamically allocated RAM-based memory pool.
>>>> > Experiments have shown that around 10-20% of pages stored in zswap
>>>> > are zero-filled pages (i.e. contents of the page are all zeros), but
>>>> > these pages are handled as normal pages by compressing and allocating
>>>> > memory in the pool.
>>>>
>>>> I am somewhat surprised that this many anon pages are zero filled.
>>>>
>>>> If this is true, then maybe we should consider solving this at the
>>>> swap level in general, as we can de-dup zero pages in all swap
>>>> devices, not just zswap.
>>>>
>>>> That being said, this is a fair small change and I don't see anything
>>>> objectionable. However, I do think the better solution would be to do
>>> this at a higher level.
>>>
>>
>> Thank you for your suggestion. It is a better solution to handle
>> zero-filled pages before swapping-out to zswap. Since, Zram is already
>> handles Zero pages internally, I considered to handle within Zswap.
>> In a long run, we can work on it to commonly handle zero-filled anon
>> pages.
>>
>>> zero-filled pages are just 1 case. in general, it's better
>>> to handle pages that are memset-ed with the same value (e.g.
>>> memset(page, 0x01, page_size)). which includes, but not
>>> limited to, 0x00. zram does it.
>>>
>>> -ss
>>
>> It is a good solution to extend zero-filled pages handling to same value
>> pages. I will work on to identify the percentage of same value pages
>> excluding zero-filled pages in Zswap and will get back.
>
> Yes, this sounds like a good modification to the patch. Also, unless
> anyone else disagrees, it may be good to control this with a module
> param - in case anyone has a use case that they know won't be helped
> by this, and the extra overhead of checking each page is wasteful.
> Probably should default to enabled.
>
>>
>> - Srividya

I have made changes to patch to handle pages with same-value filled.

I tested on a ARM Quad Core 32-bit device with 1.5GB RAM by launching
and relaunching different applications. After the test, out of ~64000
pages stored in zswap, ~ 11000 pages were same-value filled pages
(including zero-filled pages) and ~9000 pages were zero-filled pages.

An average of 17% of pages(including zero-filled pages) in zswap are
same-value filled pages and 14% pages are zero-filled pages.
An average of 3% of pages are same-filled non-zero pages.

The below table shows the execution time profiling with the patch.

Baseline With patch % Improvement
-----------------------------------------------------------------
*Zswap Store Time 26.5ms 18ms 32%
(of same value pages)
*Zswap Load Time
(of same value pages) 25.5ms 13ms 49%
-----------------------------------------------------------------

On Ubuntu PC with 2GB RAM, while executing kernel build and other test
scripts and running multimedia applications, out of 360000 pages
stored in zswap 78000(~22%) of pages were found to be same-value filled
pages (including zero-filled pages) and 64000(~17%) are zero-filled
pages. So an average of %5 of pages are same-filled non-zero pages.

The below table shows the execution time profiling with the patch.

Baseline With patch % Improvement
-----------------------------------------------------------------
*Zswap Store Time 91ms 74ms 19%
(of same value pages)
*Zswap Load Time 50ms 7.5ms 85%
(of same value pages)
-----------------------------------------------------------------

*The execution times may vary with test device used.

I will send this patch of handling same-value filled pages along with
module param to control it(default being enabled).

- Srividya