Re: [PATCH] i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency

From: CÃdric Le Goater
Date: Wed Aug 16 2017 - 07:38:58 EST


On 08/16/2017 08:49 AM, Joel Stanley wrote:
> On Tue, Aug 15, 2017 at 4:51 PM, Andrew Jeffery <andrew@xxxxxxxx> wrote:
>> In addition to the base, low and high clock configuration, the AC timing
>> register #1 on the AST2400 houses fields controlling:
>>
>> 1. tBUF: Minimum delay between Stop and Start conditions
>> 2. tHDSTA: Hold time for the Start condition
>> 3. tACST: Setup time for Start and Stop conditions, and hold time for the
>> Repeated Start condition
>>
>> These values are defined in hardware on the AST2500 and therefore don't
>> need to be set.
>>
>> aspeed_i2c_init_clk() was performing a direct write of the generated
>> clock values rather than a read/mask/modify/update sequence to retain
>> tBUF, tHDSTA and tACST, and therefore cleared the tBUF, tHDSTA and tACST
>> fields on the AST2400. This resulted in a delay/setup/hold time of 1
>> base clock, which in some configurations is not enough for some devices
>> (e.g. the MAX31785 fan controller, with an APB of 48MHz and a desired
>> bus speed of 100kHz).
>>
>> Signed-off-by: Andrew Jeffery <andrew@xxxxxxxx>
>> ---
>> drivers/i2c/busses/i2c-aspeed.c | 9 ++++++++-
>> 1 file changed, 8 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
>> index ee76e6dddc4b..284f8670dbeb 100644
>> --- a/drivers/i2c/busses/i2c-aspeed.c
>> +++ b/drivers/i2c/busses/i2c-aspeed.c
>> @@ -53,6 +53,9 @@
>> #define ASPEED_I2CD_MASTER_EN BIT(0)
>>
>> /* 0x04 : I2CD Clock and AC Timing Control Register #1 */
>> +#define ASPEED_I2CD_TIME_TBUF_MASK GENMASK(31, 28)
>> +#define ASPEED_I2CD_TIME_THDSTA_MASK GENMASK(27, 24)
>> +#define ASPEED_I2CD_TIME_TACST_MASK GENMASK(23, 20)
>> #define ASPEED_I2CD_TIME_SCL_HIGH_SHIFT 16
>> #define ASPEED_I2CD_TIME_SCL_HIGH_MASK GENMASK(19, 16)
>> #define ASPEED_I2CD_TIME_SCL_LOW_SHIFT 12
>> @@ -744,7 +747,11 @@ static int aspeed_i2c_init_clk(struct aspeed_i2c_bus *bus)
>> u32 divisor, clk_reg_val;
>>
>> divisor = DIV_ROUND_UP(bus->parent_clk_frequency, bus->bus_frequency);
>> - clk_reg_val = bus->get_clk_reg_val(divisor);
>> + clk_reg_val = readl(bus->base + ASPEED_I2C_AC_TIMING_REG1);
>> + clk_reg_val &= (ASPEED_I2CD_TIME_TBUF_MASK |
>> + ASPEED_I2CD_TIME_THDSTA_MASK |
>> + ASPEED_I2CD_TIME_TACST_MASK);
>
> Instead of keeping the u-boot values (which appear to be hard-coded),
> should we instead put the known working values in the register?

Yes. I was wondering where the initial setting was from on the AST400.

C.