Re: [PATCH v6 0/6] g_NCR5380: PDMA fixes and cleanup

From: Ondrej Zary
Date: Sat Jul 01 2017 - 17:49:52 EST


On Saturday 01 July 2017 04:40:53 Finn Thain wrote:
> Ondrej, would you please test this new series?
>
> Changed since v1:
> - PDMA transfer residual is calculated earlier.
> - End of DMA flag check is now polled (if there is any residual).
>
> Changed since v2:
> - Bail out of transfer loops when Gated IRQ gets asserted.
> - Make udelay conditional on board type.
> - Drop sg_tablesize patch due to performance regression.
>
> Changed since v3:
> - Add Ondrej's workaround for corrupt WRITE commands on DTC boards.
> - Reset the 53c400 logic after any short PDMA transfer.
> - Don't fail the transfer if the 53c400 logic got a reset.
>
> Changed since v4:
> - Bail out of transfer loops when Gated IRQ gets asserted. (Again.)
> - Always call wait_for_53c80_registers() at end of transfer.
> - Drain chip buffers after PDMA receive is interrupted.
> - Rework residual calculation.
> - Add new patch to correct DMA terminology.
>
> Changed since v5:
> - Rework residual calculation to account for on-chip buffer swap.
> - Attempt to retain the disconnect/IRQ detection in the DTC436 workaround.
> - Move all DTC436 workarounds to final patch.
>
>
> Finn Thain (2):
> g_NCR5380: Cleanup comments and whitespace
> g_NCR5380: Use unambiguous terminology for PDMA send and receive
>
> Ondrej Zary (4):
> g_NCR5380: Fix PDMA transfer size
> g_NCR5380: End PDMA transfer correctly on target disconnection
> g_NCR5380: Re-work PDMA loops
> g_NCR5380: Various DTC436 workarounds
>
> drivers/scsi/g_NCR5380.c | 273
> ++++++++++++++++++++++++++--------------------- 1 file changed, 151
> insertions(+), 122 deletions(-)

The write corruption is still present - "start" must be rolled back in both
IRQ and timeout cases. And 128 B is not enough , 256 is OK (why did it work
last time?). We just wrote a buffer to the chip but the chip is writing the
previous one to the drive - so if a problem arises, both buffers are lost.

This fixes the corruption (although the "start > 0" check seems wrong now):
--- a/drivers/scsi/g_NCR5380.c
+++ b/drivers/scsi/g_NCR5380.c
@@ -598,23 +598,17 @@ static inline int generic_NCR5380_psend(struct NCR5380_hostdata *hostdata,
CSR_HOST_BUF_NOT_RDY, 0,
hostdata->c400_ctl_status,
CSR_GATED_53C80_IRQ,
- CSR_GATED_53C80_IRQ, HZ / 64) < 0)
- break;
-
- if (NCR5380_read(hostdata->c400_ctl_status) &
- CSR_HOST_BUF_NOT_RDY) {
+ CSR_GATED_53C80_IRQ, HZ / 64) < 0 ||
+ (NCR5380_read(hostdata->c400_ctl_status) &
+ (CSR_HOST_BUF_NOT_RDY | CSR_GATED_53C80_IRQ))) {
/* The chip has done a 128 B buffer swap but the first
* buffer still has not reached the SCSI bus.
*/
if (start > 0)
- start -= 128;
+ start -= 256;
break;
}

- if (NCR5380_read(hostdata->c400_ctl_status) &
- CSR_GATED_53C80_IRQ)
- break;
-
if (hostdata->io_port && hostdata->io_width == 2)
outsw(hostdata->io_port + hostdata->c400_host_buf,
src + start, 64);


DTC seems to work too.

--
Ondrej Zary