Re: [PATCH 2/3] drm/rockchip/dsi: enable the grf clk before writing grf registers

From: John Keeping
Date: Wed Mar 15 2017 - 12:56:03 EST


On Wed, 15 Mar 2017 09:47:29 -0700, Brian Norris wrote:

> On Wed, Mar 15, 2017 at 04:42:31PM +0800, Chris Zhong wrote:
> > For RK3399, the grf clk should be enabled before writing grf registers,
> > otherwise the register value can not be changed.
> >
> > Signed-off-by: Chris Zhong <zyw@xxxxxxxxxxxxxx>
> > ---
> >
> > drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 24 ++++++++++++++++++++++++
> > 1 file changed, 24 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > index f84f9ae..d8f24f2 100644
> > --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > @@ -291,6 +291,7 @@ struct dw_mipi_dsi {
> > struct regmap *grf_regmap;
> > void __iomem *base;
> >
> > + struct clk *grf_clk;
> > struct clk *pllref_clk;
> > struct clk *pclk;
> > struct clk *phy_cfg_clk;
> > @@ -979,6 +980,16 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
> > dw_mipi_dsi_dphy_interface_config(dsi);
> > dw_mipi_dsi_clear_err(dsi);
> >
> > + /*
> > + * For the RK3399, the clk of grf must be enabled before writing grf
> > + * register.
> > + */
> > + ret = clk_prepare_enable(dsi->grf_clk);
> > + if (ret) {
> > + dev_err(dsi->dev, "Failed to enable grf_clk\n");
> > + return;
> > + }
> > +
> > if (pdata->grf_dsi0_mode_reg)
> > regmap_write(dsi->grf_regmap, pdata->grf_dsi0_mode_reg,
> > pdata->grf_dsi0_mode);
> > @@ -1003,6 +1014,8 @@ static void dw_mipi_dsi_encoder_enable(struct drm_encoder *encoder)
> > regmap_write(dsi->grf_regmap, pdata->grf_switch_reg, val);
> > dev_dbg(dsi->dev, "vop %s output to dsi0\n", (mux) ? "LIT" : "BIG");
> > dsi->dpms_mode = DRM_MODE_DPMS_ON;
> > +
> > + clk_disable_unprepare(dsi->grf_clk);
> > }
> >
> > static int
> > @@ -1238,6 +1251,17 @@ static int dw_mipi_dsi_bind(struct device *dev, struct device *master,
> > dev_dbg(dev, "have not phy_cfg_clk\n");
> > }
> >
> > + dsi->grf_clk = devm_clk_get(dev, "grf");
> > + if (IS_ERR(dsi->grf_clk)) {
> > + ret = PTR_ERR(dsi->grf_clk);
> > + if (ret != -ENOENT) {
> > + dev_err(dev, "Unable to get grf_clk: %d\n", ret);
>
> If you're going to print an error, you should probably check for
> -EPROBE_DEFER. This driver isn't quite consistent about this.
>
> > + return ret;
> > + }
> > + dsi->grf_clk = NULL;
> > + dev_dbg(dev, "have not grf_clk\n");
>
> The wording is a little awkward; maybe "no grf_clk provided\n"?
>
> Also, to be clear, this clock is required for RK3399, but not for others
> (e.g., RK3288) right? I guess this makes sense then, to just treat it as
> optional for all cases, even if you document it as "required" for
> RK3399.

If RK3399 is broken without grf_clk, I wonder if there should be a flag
in dw_mipi_dsi_plat_data so that the driver can enforce "required for
RK3399".


John