Re: [linux-sunxi] [PATCH 2/3] ARM: dts: sun8i: add usb_otg and OHCI/EHCI for usbc0 on H3

From: Chen-Yu Tsai
Date: Tue Feb 28 2017 - 11:31:11 EST


On Tue, Feb 28, 2017 at 11:57 PM, Icenowy Zheng <icenowy@xxxxxxxx> wrote:
>
>
> 28.02.2017, 23:46, "Chen-Yu Tsai" <wens@xxxxxxxx>:
>> On Tue, Feb 28, 2017 at 11:27 PM, Icenowy Zheng <icenowy@xxxxxxxx> wrote:
>>> Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
>>> or MUSB controller.
>>>
>>> Add device nodes for these controllers.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxxx>
>>> ---
>>> arch/arm/boot/dts/sun8i-h3.dtsi | 36 ++++++++++++++++++++++++++++++++++++
>>> 1 file changed, 36 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>>> index 27780b97c863..bc9a53edf371 100644
>>> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
>>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>>> @@ -206,6 +206,19 @@
>>> #size-cells = <0>;
>>> };
>>>
>>> + usb_otg: usb@01c19000 {
>>> + compatible = "allwinner,sun8i-h3-musb";
>>> + reg = <0x01c19000 0x0400>;
>>> + clocks = <&ccu CLK_BUS_OTG>;
>>> + resets = <&ccu RST_BUS_OTG>;
>>> + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
>>> + interrupt-names = "mc";
>>> + phys = <&usbphy 0>;
>>> + phy-names = "usb";
>>> + extcon = <&usbphy 0>;
>>> + status = "disabled";
>>> + };
>>> +
>>> usbphy: phy@01c19400 {
>>> compatible = "allwinner,sun8i-h3-usb-phy";
>>> reg = <0x01c19400 0x2c>,
>>> @@ -238,6 +251,29 @@
>>> #phy-cells = <1>;
>>> };
>>>
>>> + ehci0: usb@01c1a000 {
>>> + compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
>>> + reg = <0x01c1a000 0x100>;
>>> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>>> + clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
>>> + resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
>>> + phys = <&usbphy 0>;
>>> + phy-names = "usb";
>>
>> So this bit is slightly concerning. IIRC the xHCI drivers power on the phy when
>> probed, which means VBUS is _always_ going to be powered on, even when it's
>> supposed to be in peripheral mode. You're probably going to need to rework
>> either the phy or the musb driver to cope with this.
>>
>> Or maybe just dropping the phy handle here and letting the musb driver handle
>> it would work, but that requires the musb driver be loaded.
>
> In fact the MUSB driver is always needed -- to set the dr_mode.

I guess it's the same with DWC2/3 that have host controller pairs.

> And currently MUSB driver can take over the USB bus even if it's host-only by forcing
> its mode in sysfs.

IIUC that would also switch the phy muxing over to the HCI pairs.

ChenYu

>>
>> ChenYu
>>
>>> + status = "disabled";
>>> + };
>>> +
>>> + ohci0: usb@01c1a400 {
>>> + compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
>>> + reg = <0x01c1a400 0x100>;
>>> + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
>>> + clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
>>> + <&ccu CLK_USB_OHCI0>;
>>> + resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
>>> + phys = <&usbphy 0>;
>>> + phy-names = "usb";
>>> + status = "disabled";
>>> + };
>>> +
>>> ehci1: usb@01c1b000 {
>>> compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
>>> reg = <0x01c1b000 0x100>;
>>> --
>>> 2.11.1
>>>
>>> --
>>> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
>>> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
>>> For more options, visit https://groups.google.com/d/optout.
>>
>> --
>> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
>> For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
> For more options, visit https://groups.google.com/d/optout.