RE: Boot regression (was "Re: [PATCH] genhd: Do not hold event lock when scheduling workqueue elements")

From: Dexuan Cui
Date: Wed Feb 15 2017 - 08:51:49 EST


> From: hch@xxxxxx [mailto:hch@xxxxxx]
> Sent: Wednesday, February 15, 2017 00:35
> > I tested today's linux-next (next-20170214) + the 2 patches just now and
> got
> > a weird result:
> > sometimes the VM stills hung with a new calltrace (BUG: spinlock bad
> > magic) , but sometimes the VM did boot up despite the new calltrace!
> >
> > Attached is the log of a "good" boot.
> >
> > It looks we have a memory corruption issue somewhere...
>
> Yes.
It's due to an uninitialized spinlock. Please see the below.

> > Actually previously I saw the "BUG: spinlock bad magic" message once, but
> I
> > couldn't repro it later, so I didn't mention it to you.
>
> Interesting.
Ditto.
And probably my memory was inaccurate due to the long period of bisecting.
We should always see the message.

>
> A few questions on the dmesg:
>
> [ 6.208794] sd 2:0:0:0: [storvsc] Sense Key : Illegal Request [current]
> [ 6.209447] sd 2:0:0:0: [storvsc] Add. Sense: Invalid command operation
> code
> [ 6.210043] sd 3:0:0:0: [storvsc] Sense Key : Illegal Request [current]
> [ 6.210618] sd 3:0:0:0: [storvsc] Add. Sense: Invalid command operation
> code
> [ 6.212272] sd 2:0:0:0: [storvsc] Sense Key : Illegal Request [current]
> [ 6.212897] sd 2:0:0:0: [storvsc] Add. Sense: Invalid command operation
> code
> [ 6.213474] sd 3:0:0:0: [storvsc] Sense Key : Illegal Request [current]
> [ 6.214051] sd 3:0:0:0: [storvsc] Add. Sense: Invalid command operation
> code
>
> I didn't see anything like this in the other logs. Are these messages
> something usual on HyperV VMs?

The messages should be normal, and I have always seen them for years
at least.

I think they're triggered by "/sbin/hdparm /dev/sda" or
"/lib/udev/ata_id /dev/sda" in my Ubuntu 16.04 VM: during the VM
boot-up, the 2 programs are executed by the initrd's systemd-udev or other
system init scripts and the 2 programs try to run these 2 SCSI commands,
which are not supported by Hyper-V:

ATA PASS THROUGH (12) -- 0xa1
ATA PASS THROUGH (16) -- 0x85

IMO the commands are used when PATA/SATA devices are connected to
SCSI-to-ATA bridge, so it's understandable that Hyper-V doesn't support
them.

In the case of boot failure (hang), the 2 programs don't have a chance to
run, so we can't see the messages.

IMO we should ignore the messages, which should be harmless.

> [ 6.358405] XFS (sdb1): Mounting V5 Filesystem
> [ 6.404478] XFS (sdb1): Ending clean mount
> [ 7.535174] BUG: spinlock bad magic on CPU#0, swapper/0/0
> [ 7.536807] lock: host_ts+0x30/0xffffffffffffe1a0 [hv_utils], .magic:
> 00000000, .owner: <none>/-1, .owner_cpu: 0
> [ 7.538436] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc8-next-
> 20170214+ #1
> [ 7.539142] Hardware name: Microsoft Corporation Virtual Machine/Virtual
> Machine, BIOS 090006 04/28/2016
> [ 7.539142] Call Trace:
> [ 7.539142] <IRQ>
> [ 7.539142] dump_stack+0x63/0x82
> [ 7.539142] spin_dump+0x78/0xc0
> [ 7.539142] do_raw_spin_lock+0xfd/0x160
> [ 7.539142] _raw_spin_lock_irqsave+0x4c/0x60
> [ 7.539142] ? timesync_onchannelcallback+0x153/0x220 [hv_utils]
> [ 7.539142] timesync_onchannelcallback+0x153/0x220 [hv_utils]
>
> Can you resolve this address using gdb to a line of code? Once inside
> gdb do:
>
> l *(timesync_onchannelcallback+0x153)

(gdb) l *(timesync_onchannelcallback+0x153)
0xffffffffc0104593 is in timesync_onchannelcallback (drivers/hv/hv_util.c:279).
274 } else {
275 /*
276 * Save the adjusted time sample from the host and the snapshot
277 * of the current system time for PTP device.
278 */
279 spin_lock_irqsave(&host_ts.lock, flags);
280
281 cur_reftime = hyperv_cs->read(hyperv_cs);
282 host_ts.host_time = hosttime;
283 host_ts.ref_time = cur_reftime;

It turns out the "host_ts.lock" isn't initialized with spin_lock_init().
I'll submit a patch for this.

However, the SCSI issue (i.e. *sometimes* the VM fails to boot) is still there, I think.
We need to continue to debug...

Thanks,
-- Dexuan