RE: [PATCH v4] PCI: Xilinx NWL: Modifying irq chip for legacy interrupts

From: Bharat Kumar Gogada
Date: Fri Feb 03 2017 - 07:17:12 EST


> On 03/02/17 11:08, Bharat Kumar Gogada wrote:
> > - Adding mutex lock for protecting legacy mask register
> > - Few wifi end points which only support legacy interrupts, performs
> > hardware reset functionalities after disabling interrupts by invoking
> > disable_irq and then re-enable using enable_irq, they enable hardware
> > interrupts first and then virtual irq line later.
> > - The legacy irq line goes low only after DEASSERT_INTx is received.As
> > the legacy irq line is high immediately after hardware interrupts are
> > enabled but virq of EP is still in disabled state and EP handler is
> > never executed resulting no DEASSERT_INTx.If dummy irq chip is used,
> > interrutps are not masked and system is hanging with CPU stall.
> > - Adding irq chip functions instead of dummy irq chip for legacy
> > interrupts.
> > - Legacy interrupts are level sensitive, so using handle_level_irq is
> > more appropriate as it is masks interrupts until End point handles
> > interrupts and unmasks interrutps after End point handler is executed.
> > - Legacy interrupts are level triggered, virtual irq line of End Point
> > shows as edge in /proc/interrupts.
> > - Setting irq flags of virtual irq line of EP to level triggered at
> > the time of mapping.
> >
> > Signed-off-by: Bharat Kumar Gogada <bharatku@xxxxxxxxxx>
> > ---
> > drivers/pci/host/pcie-xilinx-nwl.c | 45
> +++++++++++++++++++++++++++++++++++-
> > 1 files changed, 44 insertions(+), 1 deletions(-)
> >
> > diff --git a/drivers/pci/host/pcie-xilinx-nwl.c
> > b/drivers/pci/host/pcie-xilinx-nwl.c
> > index 43eaa4a..e4605f9 100644
> > --- a/drivers/pci/host/pcie-xilinx-nwl.c
> > +++ b/drivers/pci/host/pcie-xilinx-nwl.c
> > @@ -184,6 +184,7 @@ struct nwl_pcie {
> > u8 root_busno;
> > struct nwl_msi msi;
> > struct irq_domain *legacy_irq_domain;
> > + spinlock_t leg_mask_lock;
> > };
> >
> > static inline u32 nwl_bridge_readl(struct nwl_pcie *pcie, u32 off) @@
> > -395,11 +396,52 @@ static void nwl_pcie_msi_handler_low(struct irq_desc
> *desc)
> > chained_irq_exit(chip, desc);
> > }
> >
> > +static void nwl_mask_leg_irq(struct irq_data *data) {
> > + struct irq_desc *desc = irq_to_desc(data->irq);
> > + struct nwl_pcie *pcie;
> > + unsigned long flags;
> > + u32 mask;
> > + u32 val;
> > +
> > + pcie = irq_desc_get_chip_data(desc);
> > + mask = 1 << (data->hwirq - 1);
> > + spin_lock_irqsave(&pcie->leg_mask_lock, flags);
>
> I've asked you to use a raw spinlock for a reason. If using RT, this gets turned
> into a sleeping lock...
>
In include/linux/spinlock.h
#define spin_lock_irqsave(lock, flags) \
do { \
raw_spin_lock_irqsave(spinlock_check(lock), flags); \
} while (0)

The above API invokes raw_spin_lock_irqsave know.
So is there any difference between raw_spin_lock_irqsave and spin_lock_irqsave ?

Thanks & Regards,
Bharat