Re: [PATCH v3 13/24] drm/rockchip: dw-mipi-dsi: fix escape clock rate

From: John Keeping
Date: Wed Feb 01 2017 - 12:23:31 EST


On Mon, 30 Jan 2017 15:25:10 -0500, Sean Paul wrote:

> On Sun, Jan 29, 2017 at 01:24:33PM +0000, John Keeping wrote:
> > This clock rate is derived from the PHY PLL, so it should be calculated
> > dynamically. Use the same calculation as the vendor kernel to derive
> > the escape clock speed.
> >
>
> Nit below, but
>
> Reviewed-by: Sean Paul <seanpaul@xxxxxxxxxxxx>
>
> > Signed-off-by: John Keeping <john@xxxxxxxxxxxx>
> > Reviewed-by: Chris Zhong <zyw@xxxxxxxxxxxxxx>
> > ---
> > v3:
> > - Improve the commit message a bit
> > - Add Chris' Reviewed-by
> > Unchanged in v2
> >
> > drivers/gpu/drm/rockchip/dw-mipi-dsi.c | 4 +++-
> > 1 file changed, 3 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > index 290282e86d16..c2e0ba96e0a0 100644
> > --- a/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi.c
> > @@ -710,11 +710,13 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
> >
> > static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
> > {
>
> Nit: It would be nice to add a comment to the effect of "You are not meant to
> understand this, it comes from the vendor kernel"

Actually, I think my commit message was misleading. I think I do
understand the calculation, although the TRM is not particularly clear
about it. TX_ESC_CLK_DIVISION is described as:

the division factor for the TX_Escape clock source (lanebyteclk).
The value 0 and 1 stop the TX_ESC clock generation

Now lanebyteclk is (dsi->lane_mbps >> 3) since lane_mbps is the
lane bit clock. The maximum escape mode clock from the MIPI
specification is 20MHz, so we end up needing

lanebyteclk / esc_clk_division < 20

thus:

esc_clk_division > lanebyteclk / 20

and we want esc_clk_division >= 2 to avoid disabling the clock
generation.

I'll add a comment to this effect.

> > + u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
> > +
> > dsi_write(dsi, DSI_PWR_UP, RESET);
> > dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
> > | PHY_RSTZ | PHY_SHUTDOWNZ);
> > dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
> > - TX_ESC_CLK_DIVIDSION(7));
> > + TX_ESC_CLK_DIVIDSION(esc_clk_division));
> > }
> >
> > static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
> > --
> > 2.11.0.197.gb556de5.dirty
> >
> > _______________________________________________
> > dri-devel mailing list
> > dri-devel@xxxxxxxxxxxxxxxxxxxxx
> > https://lists.freedesktop.org/mailman/listinfo/dri-devel
>