[PATCH v2 04/19] ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors

From: Steve Longerbeam
Date: Tue Jan 03 2017 - 15:58:08 EST


Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.

The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.

The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi. It is set to transmit over MIPI virtual channel 1.

Note there is a pin conflict with GPIO6. This pin functions as a power
input pin to the OV5642, but ENET uses it as the h/w workaround for
erratum ERR006687, to wake-up the ARM cores on normal RX and TX packet
done events (see 6261c4c8). So workaround 6261c4c8 is reverted here to
support the OV5642, and the "fsl,err006687-workaround-present" boolean
also must be removed. The result is that the CPUidle driver will no longer
allow entering the deep idle states on the sabrelite.

Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
---
arch/arm/boot/dts/imx6dl-sabrelite.dts | 5 ++
arch/arm/boot/dts/imx6q-sabrelite.dts | 6 ++
arch/arm/boot/dts/imx6qdl-sabrelite.dtsi | 122 ++++++++++++++++++++++++++++++-
3 files changed, 129 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts
index 0f06ca5..fec2524 100644
--- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts
@@ -48,3 +48,8 @@
model = "Freescale i.MX6 DualLite SABRE Lite Board";
compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl";
};
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
index 66d10d8..9e2d26d 100644
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
@@ -52,3 +52,9 @@
&sata {
status = "okay";
};
+
+&ipu1_csi1_from_mipi_vc1 {
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+};
+
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 1f9076e..4a50bb1 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -39,6 +39,8 @@
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

@@ -96,6 +98,15 @@
};
};

+ mipi_xclk: mipi_xclk {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <22000000>;
+ clock-output-names = "mipi_pwm3";
+ pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
+ status = "okay";
+ };
+
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
@@ -220,6 +231,22 @@
};
};

+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+ data-shift = <12>; /* Lines 19:12 used */
+ hsync-active = <1>;
+ vync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
@@ -271,9 +298,6 @@
txd1-skew-ps = <0>;
txd2-skew-ps = <0>;
txd3-skew-ps = <0>;
- interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
- <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
- fsl,err006687-workaround-present;
status = "okay";
};

@@ -302,6 +326,52 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
+
+ camera: ov5642@42 {
+ compatible = "ovti,ov5642";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5642>;
+ clocks = <&clks IMX6QDL_CLK_CKO2>;
+ clock-names = "xclk";
+ reg = <0x42>;
+ xclk = <24000000>;
+ reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+
+ port {
+ ov5642_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+
+ mipi_camera: ov5640@40 {
+ compatible = "ovti,ov5640_mipi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ clocks = <&mipi_xclk>;
+ clock-names = "xclk";
+ reg = <0x40>;
+ xclk = <22000000>;
+ reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
+ pwdn-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ov5640_to_mipi_csi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&mipi_csi_from_mipi_sensor>;
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+ };
+ };
+ };
};

&i2c3 {
@@ -374,7 +444,6 @@
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
/* Phy reset */
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x000b0
- MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
>;
};

@@ -449,6 +518,39 @@
>;
};

+ pinctrl_ov5642: ov5642grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x80000000
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x80000000
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x80000000
+ MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x80000000
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1grp-csi0 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000
+ MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x80000000
+ >;
+ };
+
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x000b0
+ MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
+ >;
+ };
+
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
@@ -605,3 +707,15 @@
vmmc-supply = <&reg_3p3v>;
status = "okay";
};
+
+&mipi_csi {
+ status = "okay";
+};
+
+/* Incoming port from sensor */
+&mipi_csi_from_mipi_sensor {
+ remote-endpoint = <&ov5640_to_mipi_csi>;
+ data-lanes = <0 1>;
+ clock-lanes = <2>;
+};
+
--
2.7.4