Re: [PATCH/RFT v2 12/17] USB: ochi-da8xx: Use a regulator for vbus/overcurrent

[David Lechner]

On 10/25/2016 03:24 AM, Axel Haslam wrote:
> On Tue, Oct 25, 2016 at 3:39 AM, David Lechner <david@xxxxxxxxxxxxxx> wrote:
> > On 10/24/2016 11:46 AM, ahaslam@xxxxxxxxxxxx wrote:
> > > From: Axel Haslam <ahaslam@xxxxxxxxxxxx>
> > >
> > > Currently, the da8xx ohci driver uses a set of gpios and callbacks in
> > > board files to handle vbus and overcurrent irqs form the power supply.
> > > However, this does not play nice when moving to a DT based boot were
> > > we wont have board files.
> > >
> > > Instead of requesting and handling the gpio, use the regulator framework
> > > to take care of enabling and disabling vbus power.
> > > This has the benefit
> > > that we dont need to pass any more platform data to the driver:
> > >
> > > These will be handled by the regulator framework:
> > > set_power   ->  regulator_enable/regulator_disable
> > > get_power   ->  regulator_is_enabled
> > > get_oci     ->  regulator_get_mode
> > > ocic_notify ->  regulator notification
> > >
> > > We can keep the default potpgt and use the regulator start delay instead:
> > > potpgt      -> regulator startup delay time
> > >
> > > The hawk board does not have a GPIO/OVERCURRENT gpio to control vbus,
> > > (they should not have been decleared/reserved) so, just remove those
> > > definitions from the hwk board file.
> > >
> > > Signed-off-by: Axel Haslam <ahaslam@xxxxxxxxxxxx>
> > > ---
> >
> >
> >
> > How do you recover after an overcurrent event?
> >
> > I have configured a fixed-regulator using device-tree, but similar to the
> > configuration in the board files here. However, when I shorted out the VBUS
> > and caused an overcurrent event, I see nothing in the kernel log saying that
> > there was an overcurrent event and after I remove the short, the regulator
> > is never turned back on.
>
> You should have the patch to fix gpiolib, and you should declare the
> over current gpio on the regulator as such:
> (if the pin is enabled high you should add oc-active-high);
>
>        vbus_fixed: fixed-regulator-vbus {
>                compatible = "regulator-fixed";
>                gpio = <&gpio 109 0>;
>                oc-gpio = <&gpio 36 0>;
>                regulator-boot-on;
>                enable-active-high;
>                regulator-name = "vbus";
>                regulator-min-microvolt = <5000000>;
>                regulator-max-microvolt = <5000000>;
>        };
>
>
> Question: Do you see that the over current gpio was requested
> in debugfs/gpio? and, do you see the interrupt in /proc/interrupts?
>
> If you unplug and plug in back the usb device it should work again.
> also you can unbind and bind it should also start to work:
> something like:
>
> echo usb1 >/sys/bus/usb/drivers/usb/unbind
> echo usb1 >/sys/bus/usb/drivers/usb/bind

I have added oc-active-high and I get different results, but it is still 
not quite right. When I short the VBUS, I can see that my overcurrent 
gpio changes state. However, the driver does not turn of the VBUS. When 
I remove the short, I get an overcurrent error in the kernel log. I 
would expect this when I create the short, not when I remove it. I also 
tried adding  GPIO_ACTIVE_LOW to the oc-gpio, but this did not change 
the behavior. In either case, the oc_gpio shows as high under normal 
conditions, so perhaps there is a problem with the gpio-davinci driver 
not picking up GPIO_ACTIVE_LOW from the device tree.


My regulator is basically the same. My device just uses different gpios.

	vbus_reg: vbus-reg {
		compatible = "regulator-fixed";
		pinctrl-names = "default";
		pinctrl-0 = <&usb11_pins>;
		gpio = <&gpio 101 GPIO_ACTIVE_LOW>;
		oc-gpio = <&gpio 99 0>;
		enable-active-high;
		oc-active-high;
		regulator-name = "vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
	}


It seems to me though that I should not have oc-active-high since under 
normal conditions, the oc_gpio is high and during an overcurrent event, 
the oc_gpio is low. Double-checking the behavior without oc-active-high, 
I see that the vbus gpio is turned off in response to the overcurrent 
event, but I don't get the overcurrent message in the kernel log. 
Perhaps this is because as soon as there is an overcurrent event the 
vbus turns off and the oc_gpio returns to normal before the usb driver 
has a chance to poll the overcurrent state?

Also, unplugging the device and plugging it back in does nothing. 
Unbinding and binding the driver does work, but that does not seem like 
a very nice way to have to recover from an overcurrent event.