Re: [PATCHv2] backlight: pwm_bl: disable PWM when 'duty_cycle' is zero

From: Lothar WaÃmann
Date: Sat Jun 11 2016 - 03:08:34 EST


Hi,

On Fri, 10 Jun 2016 15:54:49 +0100 Lee Jones wrote:
> On Fri, 10 Jun 2016, Lothar WaÃmann wrote:
> > On Fri, 10 Jun 2016 08:44:49 +0100 Lee Jones wrote:
> > > On Fri, 10 Jun 2016, Lothar WaÃmann wrote:
> > >
> > > > Hi,
> > > >
> > > > On Thu, 9 Jun 2016 14:51:25 +0100 Lee Jones wrote:
> > > > > On Tue, 07 Jun 2016, Lothar WaÃmann wrote:
> > > > >
> > > > > > 'brightness' is usually an index into a table of duty_cycle values,
> > > > > > where the value at index 0 may well be non-zero
> > > > > > (tegra30-apalis-eval.dts and tegra30-colibri-eval-v3.dts are real-life
> > > > > > examples).
> > > > > > Thus brightness == 0 does not necessarily mean that the PWM output
> > > > > > will be inactive.
> > > > > > Check for 'duty_cycle == 0' rather than 'brightness == 0' to decide
> > > > > > whether to disable the PWM.
> > > > > >
> > > > > > Signed-off-by: Lothar WaÃmann <LW@xxxxxxxxxxxxxxxxxxx>
> > > > > > ---
> > > > > > Changes wrt. v1:
> > > > > > - update binding docs to reflect the change
> > > > > >
> > > > > > .../devicetree/bindings/leds/backlight/pwm-backlight.txt | 9 ++++++---
> > > > > > drivers/video/backlight/pwm_bl.c | 4 ++--
> > > > > > 2 files changed, 8 insertions(+), 5 deletions(-)
> > > > > >
> > > > > > diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
> > > > > > index 764db86..95fa8a9 100644
> > > > > > --- a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
> > > > > > +++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
> > > > > > @@ -4,10 +4,13 @@ Required properties:
> > > > > > - compatible: "pwm-backlight"
> > > > > > - pwms: OF device-tree PWM specification (see PWM binding[0])
> > > > > > - brightness-levels: Array of distinct brightness levels. Typically these
> > > > > > - are in the range from 0 to 255, but any range starting at 0 will do.
> > > > > > + are in the range from 0 to 255, but any range will do.
> > > > > > The actual brightness level (PWM duty cycle) will be interpolated
> > > > > > - from these values. 0 means a 0% duty cycle (darkest/off), while the
> > > > > > - last value in the array represents a 100% duty cycle (brightest).
> > > > > > + from these values. 0 means a 0% duty cycle, while the highest value in
> > > > > > + the array represents a 100% duty cycle.
> > > > > > + The range may be in reverse order (starting with the maximum duty cycle
> > > > > > + value) to create a PWM signal with the 100% duty cycle representing
> > > > > > + minimum and 0% duty cycle maximum brigthness.
> > > > > > - default-brightness-level: the default brightness level (index into the
> > > > > > array defined by the "brightness-levels" property)
> > > > > > - power-supply: regulator for supply voltage
> > > > > > diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
> > > > > > index b2b366b..80b2b52 100644
> > > > > > --- a/drivers/video/backlight/pwm_bl.c
> > > > > > +++ b/drivers/video/backlight/pwm_bl.c
> > > > > > @@ -103,8 +103,8 @@ static int pwm_backlight_update_status(struct backlight_device *bl)
> > > > > > if (pb->notify)
> > > > > > brightness = pb->notify(pb->dev, brightness);
> > > > > >
> > > > > > - if (brightness > 0) {
> > > > > > - duty_cycle = compute_duty_cycle(pb, brightness);
> > > > > > + duty_cycle = compute_duty_cycle(pb, brightness);
> > > > > > + if (duty_cycle > 0) {
> > > > >
> > > > > How does this work in the aforementioned:
> > > > >
> > > > > "The range may be in reverse order"
> > > > >
> > > > > ... case? Surely when duty_cycle is when the screen should be at it's
> > > > > brightest? Wouldn't it confuse the user if they turn their brightness
> > > > > *up* and the screen goes *off*?
> > > > >
> > > > Assuming that the PWM output is inactive (LOW) when the duty_cycle is
> > > > set to zero, there will be no difference between operating the PWM at
> > > > duty_cycle 0 or disabling it.
> > > >
> > > > Currently, the screen will go bright when it should be off in this
> > > > case.
> > >
> > > It sounds like we need something that lets the framework know if
> > > duty_cycle = MAX is the brightest or if duty_cycle = 0 is. Either way
> > > someone is going to get screwed by this logic.
> > >
> > The backlight framework does not (and does not need to) know anything
> > about PWM duty cycles. Its 'brightness' values are consistently 0 ==
> > dark, max == brightest in either case.
>
> What I'm getting at is; by the look of the documentation, the
> brightest setting can either be a duty cycle of 0 or 255. So what
> happens with your new semantics when the duty cycle of 0 represents
> the brightest setting and you reach 0? Didn't you just turn the
> backlight off?
>
As mentioned earlier, disabling the PWM has generally the same result as
setting the duty cycle to 0. The current behaviour is broken in this
case, since setting brightness to 0 with a non-zero duty_cycle as the
first element of brightness-levels, the PWM will be disabled rather than
switched to the given duty cycle.
Disabling the PWM should have the same effect as setting the duty cycle
to 0, so it is safe to check for duty_cycle == 0 to decide whether to
disable the PWM.


Lothar WaÃmann