Re: [PATCH v7 08/14] usb: otg: add OTG/dual-role core

[Peter Chen]

On Mon, May 02, 2016 at 03:18:51PM +0300, Roger Quadros wrote:
> +
> +	if (config->otg_work)	/* custom otg_work ? */
> +		INIT_WORK(&otg->work, config->otg_work);
> +	else
> +		INIT_WORK(&otg->work, usb_drd_work);
> +
> +	otg->wq = create_singlethread_workqueue("usb_otg");

Using create_freezable_workqueue like I suggested before.

> + */
> +
> +#ifndef __DRIVERS_USB_COMMON_USB_OTG_H
> +#define __DRIVERS_USB_COMMON_USB_OTG_H
> +
> +/*
> + *  A-DEVICE timing constants
> + */
> +
> +/* Wait for VBUS Rise  */
> +#define TA_WAIT_VRISE        (100)	/* a_wait_vrise: section 7.1.2
> +					 * a_wait_vrise_tmr: section 7.4.5.1
> +					 * TA_VBUS_RISE <= 100ms, section 4.4
> +					 * Table 4-1: Electrical Characteristics
> +					 * ->DC Electrical Timing
> +					 */
> +/* Wait for VBUS Fall  */
> +#define TA_WAIT_VFALL        (1000)	/* a_wait_vfall: section 7.1.7
> +					 * a_wait_vfall_tmr: section: 7.4.5.2
> +					 */
> +/* Wait for B-Connect */
> +#define TA_WAIT_BCON         (10000)	/* a_wait_bcon: section 7.1.3
> +					 * TA_WAIT_BCON: should be between 1100
> +					 * and 30000 ms, section 5.5, Table 5-1
> +					 */
> +/* A-Idle to B-Disconnect */
> +#define TA_AIDL_BDIS         (5000)	/* a_suspend min 200 ms, section 5.2.1
> +					 * TA_AIDL_BDIS: section 5.5, Table 5-1
> +					 */
> +/* B-Idle to A-Disconnect */
> +#define TA_BIDL_ADIS         (500)	/* TA_BIDL_ADIS: section 5.2.1
> +					 * 500ms is used for B switch to host
> +					 * for safe
> +					 */
> +
> +/*
> + * B-device timing constants
> + */
> +
> +/* Data-Line Pulse Time*/
> +#define TB_DATA_PLS          (10)	/* b_srp_init,continue 5~10ms
> +					 * section:5.1.3
> +					 */
> +/* SRP Fail Time  */
> +#define TB_SRP_FAIL          (6000)	/* b_srp_init,fail time 5~6s
> +					 * section:5.1.6
> +					 */
> +/* A-SE0 to B-Reset  */
> +#define TB_ASE0_BRST         (155)	/* minimum 155 ms, section:5.3.1 */
> +/* SE0 Time Before SRP */
> +#define TB_SE0_SRP           (1000)	/* b_idle,minimum 1s, section:5.1.2 */
> +/* SSEND time before SRP */
> +#define TB_SSEND_SRP         (1500)	/* minimum 1.5 sec, section:5.1.2 */
> +
> +#define TB_SESS_VLD          (1000)

Seems you agree to remove above definitions.

>  
>  	/* Current usb protocol used: 0:undefine; 1:host; 2:client */
> diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h
> index 85b8fb5..b094352 100644
> --- a/include/linux/usb/otg.h
> +++ b/include/linux/usb/otg.h
> @@ -10,10 +10,55 @@
>  #define __LINUX_USB_OTG_H
>  
>  #include <linux/phy/phy.h>
> -#include <linux/usb/phy.h>
> -#include <linux/usb/otg-fsm.h>
> +#include <linux/device.h>
> +#include <linux/hrtimer.h>
> +#include <linux/ktime.h>

Above two headers are not needed

-- 

Best Regards,
Peter Chen