[PATCH] tty: add Moxa Smartio MUE serial driver
From: Mathieu OTHACEHE
Date: Mon Feb 01 2016 - 15:34:46 EST
Add a driver which supports:
- CP-102E: 2 ports RS232 PCIE card
- CP-102EL: 2 ports RS232 PCIE card
- CP-132EL: 2 ports RS422/485 PCIE card
- CP-114EL: 4 ports RS232/422/485 PCIE card
- CP-104EL-A: 4 ports RS232 PCIE card
- CP-168EL-A: 8 ports RS232 PCIE card
- CP-118EL-A: 8 ports RS232/422/485 PCIE card
- CP-118E-A: 8 ports RS422/485 PCIE card
- CP-138E-A: 8 ports RS422/485 PCIE card
- CP-134EL-A: 4 ports RS422/485 PCIE card
- CP-116E-A (A): 8 ports RS232/422/485 PCIE card
- CP-116E-A (B): 8 ports RS232/422/485 PCIE card
This driver is based on 1.16.7 GPL MOXA driver written by Eric Lo
and available on MOXA website. The original driver was based on
Linux serial driver.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@xxxxxxxxx>
---
Hi,
Here is a new driver for MOXA Smartio MUE cards. It is based
on the vendor driver available on MOXA website and on the
mainline mxser driver.
I was able to test it on a CP-168EL-A card on PC. Some of the
cards (118E-A, 138E-A, 134EL-A, 116E-A-A et 116E-A-B) have
a CPLD module programmable via GPIO.
For now, I dropped all the code related to CPLD/GPIO because I
can't test it on my card.
Mathieu
MAINTAINERS | 5 +
drivers/tty/Kconfig | 10 +
drivers/tty/Makefile | 1 +
drivers/tty/mxupcie.c | 1874 +++++++++++++++++++++++++++++++++++++++++++++++++
drivers/tty/mxupcie.h | 129 ++++
5 files changed, 2019 insertions(+)
create mode 100644 drivers/tty/mxupcie.c
create mode 100644 drivers/tty/mxupcie.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 2b4eb31..3e6c950 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7274,6 +7274,11 @@ S: Maintained
F: Documentation/serial/moxa-smartio
F: drivers/tty/mxser.*
+MOXA SMARTIO/INDUSTIO MUE SERIAL CARD
+M: Mathieu Othacehe <m.othacehe@xxxxxxxxx>
+S: Maintained
+F: drivers/tty/mxupcie.*
+
MR800 AVERMEDIA USB FM RADIO DRIVER
M: Alexey Klimov <klimov.linux@xxxxxxxxx>
L: linux-media@xxxxxxxxxxxxxxx
diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
index c01f450..8a14bd075 100644
--- a/drivers/tty/Kconfig
+++ b/drivers/tty/Kconfig
@@ -259,6 +259,16 @@ config MOXA_SMARTIO
This driver can also be built as a module. The module will be called
mxser. If you want to do that, say M here.
+config MOXA_SMARTIO_MUE
+ tristate "Moxa SmartIO MUE support"
+ depends on SERIAL_NONSTANDARD && PCI
+ help
+ Say Y here if you have a Moxa SmartIO MUE multiport serial card
+ and/or want to help develop a new version of this driver.
+
+ This driver can also be built as a module. The module will be called
+ mxupcie. If you want to do that, say M here.
+
config SYNCLINK
tristate "Microgate SyncLink card support"
depends on SERIAL_NONSTANDARD && PCI && ISA_DMA_API
diff --git a/drivers/tty/Makefile b/drivers/tty/Makefile
index 5817e23..0e37ff2 100644
--- a/drivers/tty/Makefile
+++ b/drivers/tty/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_CYCLADES) += cyclades.o
obj-$(CONFIG_ISI) += isicom.o
obj-$(CONFIG_MOXA_INTELLIO) += moxa.o
obj-$(CONFIG_MOXA_SMARTIO) += mxser.o
+obj-$(CONFIG_MOXA_SMARTIO_MUE) += mxupcie.o
obj-$(CONFIG_NOZOMI) += nozomi.o
obj-$(CONFIG_ROCKETPORT) += rocket.o
obj-$(CONFIG_SYNCLINK_GT) += synclink_gt.o
diff --git a/drivers/tty/mxupcie.c b/drivers/tty/mxupcie.c
new file mode 100644
index 0000000..ffdcb5b
--- /dev/null
+++ b/drivers/tty/mxupcie.c
@@ -0,0 +1,1874 @@
+/*
+ * mxupcie.c -- MOXA Smartio/Industio MUE multiport serial driver.
+ *
+ * Copyright (C) 1999-2015 Moxa Technologies (support@xxxxxxxx).
+ * Copyright (C) 2016 Mathieu OTHACEHE <m.othacehe@xxxxxxxxx>
+ *
+ * This code is based on the 1.16.7 moxa driver which is based on
+ * Linux serial driver.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/serial_reg.h>
+#include <linux/delay.h>
+#include <linux/major.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+
+#include "mxupcie.h"
+
+enum {
+ MXUPCIE_BOARD_CP102E = 0,
+ MXUPCIE_BOARD_CP102EL,
+ MXUPCIE_BOARD_CP132EL,
+ MXUPCIE_BOARD_CP114EL,
+ MXUPCIE_BOARD_CP104EL_A,
+ MXUPCIE_BOARD_CP168EL_A,
+ MXUPCIE_BOARD_CP118EL_A,
+ MXUPCIE_BOARD_CP118E_A_I,
+ MXUPCIE_BOARD_CP138E_A,
+ MXUPCIE_BOARD_CP134EL_A,
+ MXUPCIE_BOARD_CP116E_A_A,
+ MXUPCIE_BOARD_CP116E_A_B
+};
+
+struct mxupcie_card_info {
+ char *name;
+ unsigned int nports;
+ int flags;
+};
+
+static const struct mxupcie_card_info mxupcie_cards[] = {
+ {"CP-102E series", 2, MX_FLAG_232},
+ {"CP-102EL series", 2, MX_FLAG_232},
+ {"CP-132EL series", 2, MX_FLAG_422 | MX_FLAG_485},
+ {"CP-114EL series", 4, MX_FLAG_232 | MX_FLAG_422 | MX_FLAG_485},
+ {"CP-104EL-A series", 4, MX_FLAG_232},
+ {"CP-168EL-A series", 8, MX_FLAG_232},
+ {"CP-118EL-A series", 8, MX_FLAG_232 | MX_FLAG_422 | MX_FLAG_485},
+ {"CP-118E-A series", 8, MX_FLAG_422 | MX_FLAG_485},
+ {"CP-138E-A series", 8, MX_FLAG_422 | MX_FLAG_485},
+ {"CP-134EL-A series", 4, MX_FLAG_422 | MX_FLAG_485},
+ {"CP-116E-A series (A)", 8, MX_FLAG_232 | MX_FLAG_422 | MX_FLAG_485},
+ {"CP-116E-A series (B)", 8, MX_FLAG_232 | MX_FLAG_422 | MX_FLAG_485}
+};
+
+static struct pci_device_id mxupcie_pcibrds[] = {
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102E), MXUPCIE_BOARD_CP102E},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102EL), MXUPCIE_BOARD_CP102EL},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP132EL), MXUPCIE_BOARD_CP132EL},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114EL), MXUPCIE_BOARD_CP114EL},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP104EL_A), MXUPCIE_BOARD_CP104EL_A},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP168EL_A), MXUPCIE_BOARD_CP168EL_A},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP118EL_A), MXUPCIE_BOARD_CP118EL_A},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP118E_A_I), MXUPCIE_BOARD_CP118E_A_I},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138E_A), MXUPCIE_BOARD_CP138E_A},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP134EL_A), MXUPCIE_BOARD_CP134EL_A},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP116E_A_A), MXUPCIE_BOARD_CP116E_A_A},
+ {PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP116E_A_B), MXUPCIE_BOARD_CP116E_A_B},
+ {0}
+};
+
+MODULE_DEVICE_TABLE(pci, mxupcie_pcibrds);
+
+static unsigned char interface;
+module_param(interface, byte, 0);
+
+struct mxupcie_port {
+ struct tty_port port;
+ struct mxupcie_board *board;
+ int port_index;
+ unsigned char *ioaddr;
+ int baud_base;
+ int read_status_mask;
+ int custom_divisor;
+ int close_delay;
+ unsigned short closing_wait;
+ int ier;
+ int mcr;
+ int xmit_head;
+ int xmit_tail;
+ int xmit_cnt;
+ struct async_icount icount;
+ int timeout;
+ int max_baud;
+ spinlock_t slock;
+ int speed;
+ int custom_baud_rate;
+ unsigned char uir;
+ unsigned long uir_addr;
+};
+
+struct mxupcie_board {
+ int irq;
+ unsigned int index;
+ unsigned long iobar3_addr;
+ const struct mxupcie_card_info *cinfo;
+ struct mxupcie_port ports[MXUPCIE_PORTS_PER_BOARD];
+};
+
+static struct tty_driver *mx_drv;
+struct mxupcie_board mxupcie_boards[MXUPCIE_BOARDS];
+
+static void mxupcie_init_terminator(struct mxupcie_port *info)
+{
+ struct mxupcie_board *board = info->board;
+
+ if (board->cinfo->flags & (MX_FLAG_422 | MX_FLAG_485) &&
+ board->cinfo->nports > 2) {
+ outb(0xff, board->iobar3_addr + MOXA_PUART_GPIO_EN);
+ outb(0x00, board->iobar3_addr + MOXA_PUART_GPIO_OUT);
+ }
+}
+
+static int mxupcie_set_terminator(struct mxupcie_port *info, unsigned char val)
+{
+ unsigned char chip_val = 0;
+ struct mxupcie_board *board = info->board;
+
+ if (info->uir == MOXA_UIR_RS232)
+ return -EINVAL;
+
+ switch (val) {
+ case MX_TERM_NONE:
+ case MX_TERM_120:
+ chip_val = inb(board->iobar3_addr + MOXA_PUART_GPIO_IN);
+ if (board->cinfo->nports == 2) {
+ chip_val &= ~(1 << (info->port_index + 2));
+ chip_val |= (val << (info->port_index + 2));
+ } else if (board->cinfo->nports > 2) {
+ chip_val &= ~(1 << info->port_index);
+ chip_val |= (val << info->port_index);
+ }
+
+ outb(0xff, board->iobar3_addr + MOXA_PUART_GPIO_EN);
+ outb(chip_val, board->iobar3_addr + MOXA_PUART_GPIO_OUT);
+
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int mxupcie_chars_in_buffer(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+
+ return info->xmit_cnt;
+}
+
+static void mxupcie_flush_buffer(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ char fcr;
+ int i;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ /*
+ * TxFIFO has two pointer, w_ptr and r_ptr, but use the different clock.
+ * W_ptr uses pcie clock, and r_ptr uses uart clock.
+ * When set "TX FIFO Flush" bit,
+ * w_ptr will be clear to 0 first as pcie clock is faster.
+ * In this time, r_ptr is not clear to 0, so 795x will consider
+ * there are more data (w_ptr-r_ptr) need be transmitted.
+ *
+ * It is advised to reset 5 times or much more.
+ */
+ fcr = ioread8(info->ioaddr + UART_FCR);
+
+ for (i = 0; i < 5; i++) {
+ iowrite8((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
+ info->ioaddr + UART_FCR);
+ }
+
+ iowrite8(fcr, info->ioaddr + UART_FCR);
+
+ tty_wakeup(tty);
+}
+
+/*
+ * This routine is called to set the UART divisor registers to match
+ * the specified baud rate for a serial port.
+ */
+static void write_div_scr(unsigned char *base,
+ signed short div,
+ unsigned char scr)
+{
+ unsigned char lcr;
+ unsigned char oldsfr, sfr;
+
+ oldsfr = ioread8(base + MOXA_PUART_SFR);
+ sfr = oldsfr & (~(MOXA_SFR_ENABLE_TCNT));
+ iowrite8(sfr, base + MOXA_PUART_SFR);
+ iowrite8(scr, base + MOXA_PUART_SCR);
+ iowrite8(oldsfr, base + MOXA_PUART_SFR);
+
+ lcr = ioread8(base + UART_LCR);
+ iowrite8(lcr | UART_LCR_DLAB, base + UART_LCR);
+ iowrite8(div & 0xff, base + MOXA_PUART_LSB);
+ iowrite8((div & 0xff00) >> 8, base + MOXA_PUART_MSB);
+ iowrite8(lcr, base + UART_LCR);
+}
+
+static int set_linear_baud(unsigned char *base, long newspd)
+{
+ unsigned char scr, cpr;
+ unsigned short div;
+ int i, j, divisor = 0, sequence = 0;
+ int M, N = 0, SCR = 0;
+ int set_value, min, ret_value, accuracy;
+
+ M = MIN_CPRM;
+ set_value = newspd;
+
+ min = FREQUENCY;
+ ret_value = 0;
+
+ for (i = 1; i <= MAXDIVISOR; i++) {
+ for (j = MINSEQUENCE; j <= MAXSEQUENCE;) {
+ if (FREQUENCY / (i * j) > set_value)
+ accuracy = (FREQUENCY / (i * j)) - set_value;
+ else
+ accuracy = set_value - (FREQUENCY / (i * j));
+
+ if (min > accuracy) {
+ min = accuracy;
+ ret_value = (FREQUENCY / (i * j));
+ divisor = i;
+ sequence = j;
+ }
+
+ if (j <= MAXSEQUENCE / 2)
+ j += 1;
+ else
+ j += 2;
+ }
+ }
+ if ((min * 100) / (set_value * 100) <= 3) {
+ if (sequence > (MAXSEQUENCE / 2)) {
+ M = MAX_CPRM;
+ sequence /= 2;
+ }
+ for (i = MAX_SCR; i >= MIN_SCR; i--) {
+ for (j = MIN_CPRN; j <= MAX_CPRN; j++) {
+ if ((16 - i + j) == sequence) {
+ SCR = i;
+ N = j;
+ }
+ }
+ }
+ }
+ scr = (unsigned char)SCR;
+ div = (unsigned short)divisor;
+ cpr = (M << 3) + N;
+
+ iowrite8(ioread8(base + UART_MCR) | UART_MCR_CLKSEL, base + UART_MCR);
+ iowrite8(cpr, base + MOXA_PUART_CPR);
+ write_div_scr(base, div, scr);
+
+ return 0;
+}
+
+static int mxupcie_set_baud(struct tty_struct *tty, long newspd)
+{
+ int quot = 0;
+ unsigned char cval;
+ int custom = 0;
+ struct mxupcie_port *info = tty->driver_data;
+
+ if (newspd > info->max_baud)
+ return 0;
+
+ if (newspd == 38400 &&
+ (info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) {
+ info->speed = info->custom_baud_rate;
+ custom = 1;
+
+ quot = info->baud_base / info->speed;
+ if (info->speed <= 0 || info->speed > info->max_baud)
+ quot = 0;
+ else
+ set_linear_baud(info->ioaddr, info->speed);
+ } else {
+ if (newspd == 134) {
+ quot = (2 * info->baud_base / 269);
+ info->speed = 134;
+ } else if (newspd) {
+ quot = info->baud_base / newspd;
+ info->baud_base = 921600;
+ if (quot == 0)
+ quot = 1;
+ } else {
+ quot = 0;
+ }
+ }
+
+ info->timeout = ((MX_TX_FIFO_SIZE * HZ * 10 * quot) / info->baud_base);
+ info->timeout += HZ / 50; /* Add .02 seconds of slop */
+
+ if (quot) {
+ info->mcr |= UART_MCR_DTR;
+ iowrite8(info->mcr, info->ioaddr + UART_MCR);
+ } else {
+ info->mcr &= ~UART_MCR_DTR;
+ iowrite8(info->mcr, info->ioaddr + UART_MCR);
+
+ return 0;
+ }
+
+ if (!custom) {
+ cval = ioread8(info->ioaddr + UART_LCR);
+ /* set DLAB */
+ iowrite8(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR);
+ /* LS of divisor */
+ iowrite8(quot & 0xff, info->ioaddr + UART_DLL);
+ /* MS of divisor */
+ iowrite8(quot >> 8, info->ioaddr + UART_DLM);
+ /* reset DLAB */
+ iowrite8(cval, info->ioaddr + UART_LCR);
+ iowrite8(0x08, info->ioaddr + MOXA_PUART_CPR);
+ }
+
+ return 0;
+}
+
+static int mxupcie_change_speed(struct tty_struct *tty,
+ struct ktermios *old_termios)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned cval, fcr;
+ int reg_flag;
+
+ mxupcie_set_baud(tty, tty_get_baud_rate(tty));
+
+ /* byte size and parity */
+ switch (C_CSIZE(tty)) {
+ case CS5:
+ cval = 0x00;
+ break;
+ case CS6:
+ cval = 0x01;
+ break;
+ case CS7:
+ cval = 0x02;
+ break;
+ case CS8:
+ cval = 0x03;
+ break;
+ default:
+ cval = 0x00;
+ break; /* too keep GCC shut... */
+ }
+
+ if (C_CSTOPB(tty))
+ cval |= 0x04;
+
+ if (C_PARENB(tty))
+ cval |= UART_LCR_PARITY;
+
+ if (!C_PARODD(tty))
+ cval |= UART_LCR_EPAR;
+
+ fcr = UART_FCR_ENABLE_FIFO;
+
+ /* CTS flow control flag and modem status interrupts */
+ info->ier &= ~UART_IER_MSI;
+
+ reg_flag = ioread8(info->ioaddr + MOXA_PUART_EFR);
+
+ if (C_CRTSCTS(tty)) {
+ info->ier |= UART_IER_MSI;
+ reg_flag |= (MOXA_EFR_AUTO_RTS | MOXA_EFR_AUTO_CTS);
+ } else {
+ reg_flag &= ~(MOXA_EFR_AUTO_RTS | MOXA_EFR_AUTO_CTS);
+ }
+
+ iowrite8(info->mcr, info->ioaddr + UART_MCR);
+
+ if (C_CLOCAL(tty)) {
+ info->port.flags &= ~ASYNC_CHECK_CD;
+ } else {
+ info->port.flags |= ASYNC_CHECK_CD;
+ info->ier |= UART_IER_MSI;
+ }
+
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+
+ /* Set up parity check flag */
+ info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+
+ if (I_INPCK(tty))
+ info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+
+ if (I_BRKINT(tty) || I_PARMRK(tty))
+ info->read_status_mask |= UART_LSR_BI;
+
+ if (I_IGNBRK(tty)) {
+ info->read_status_mask |= UART_LSR_BI;
+ if (I_IGNPAR(tty)) {
+ info->read_status_mask |= UART_LSR_OE |
+ UART_LSR_PE | UART_LSR_FE;
+ }
+ }
+
+ iowrite8(START_CHAR(tty), info->ioaddr + MOXA_PUART_XON1);
+ iowrite8(START_CHAR(tty), info->ioaddr + MOXA_PUART_XON2);
+ iowrite8(STOP_CHAR(tty), info->ioaddr + MOXA_PUART_XOFF1);
+ iowrite8(STOP_CHAR(tty), info->ioaddr + MOXA_PUART_XOFF2);
+
+ if (I_IXON(tty))
+ reg_flag |= MOXA_EFR_TX_SW;
+ else
+ reg_flag &= ~MOXA_EFR_TX_SW;
+
+ if (I_IXOFF(tty))
+ reg_flag |= MOXA_EFR_RX_SW;
+ else
+ reg_flag &= ~MOXA_EFR_RX_SW;
+
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_EFR);
+ iowrite8(fcr, info->ioaddr + UART_FCR);
+ iowrite8(cval, info->ioaddr + UART_LCR);
+
+ return 0;
+}
+
+static int mxupcie_activate(struct tty_port *port, struct tty_struct *tty)
+{
+ struct mxupcie_port *info;
+ unsigned long page;
+ unsigned char reg_flag;
+ unsigned long sp_flags;
+
+ info = container_of(port, struct mxupcie_port, port);
+
+ page = __get_free_page(GFP_KERNEL);
+ if (!page)
+ return -ENOMEM;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+
+ if (info->port.xmit_buf)
+ free_page(page);
+ else
+ info->port.xmit_buf = (unsigned char *)page;
+
+ /*
+ * Clear the FIFO buffers and disable them
+ * (they will be reenabled in mxupcie_change_speed())
+ */
+ iowrite8((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
+ info->ioaddr + UART_FCR);
+
+ /*
+ * At this point there's no way the LSR could still be 0xFF;
+ * if it is, then bail out, because there's likely no UART
+ * here.
+ */
+ if (ioread8(info->ioaddr + UART_LSR) == 0xff) {
+ set_bit(TTY_IO_ERROR, &tty->flags);
+ goto err;
+ }
+
+ /* Clear the interrupt registers. */
+ (void)ioread8(info->ioaddr + UART_LSR);
+ (void)ioread8(info->ioaddr + UART_RX);
+ (void)ioread8(info->ioaddr + UART_IIR);
+ (void)ioread8(info->ioaddr + UART_MSR);
+
+ /* Now, initialize the UART */
+ iowrite8(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
+ info->mcr = UART_MCR_DTR | UART_MCR_RTS;
+ iowrite8(info->mcr, info->ioaddr + UART_MCR);
+
+ /* Initialize enhance mode register */
+ reg_flag = MOXA_EFR_ENHANCE;
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_EFR);
+
+ reg_flag = MOXA_SFR_950 | MOXA_SFR_ENABLE_TCNT;
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_SFR);
+
+ iowrite8(MX_TX_FIFO_SIZE, info->ioaddr + MOXA_PUART_TTL);
+ iowrite8(MOXA_RTL_96, info->ioaddr + MOXA_PUART_RTL);
+ iowrite8(MOXA_FCL_16, info->ioaddr + MOXA_PUART_FCL);
+ iowrite8(MOXA_FCH_110, info->ioaddr + MOXA_PUART_FCH);
+
+ /* Finally, enable interrupts */
+ info->ier = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+
+ /* And clear the interrupt registers again for luck. */
+ (void)ioread8(info->ioaddr + UART_LSR);
+ (void)ioread8(info->ioaddr + UART_RX);
+ (void)ioread8(info->ioaddr + UART_IIR);
+ (void)ioread8(info->ioaddr + UART_MSR);
+
+ info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
+ mxupcie_change_speed(tty, NULL);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ return 0;
+err:
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ free_page(page);
+
+ return 0;
+}
+
+static void mxupcie_shutdown(struct tty_port *port)
+{
+ struct mxupcie_port *info;
+ unsigned char reg_flag;
+ int i;
+ unsigned long sp_flags;
+
+ info = container_of(port, struct mxupcie_port, port);
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+
+ wake_up_interruptible(&info->port.delta_msr_wait);
+
+ if (info->port.xmit_buf) {
+ free_page((unsigned long)info->port.xmit_buf);
+ info->port.xmit_buf = NULL;
+ }
+
+ reg_flag = 0;
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_EFR);
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_SFR);
+
+ info->ier = 0;
+ iowrite8(0x00, info->ioaddr + UART_IER);
+
+ if (info->speed < 9600) {
+ int sleep_interval = 0;
+ int reset_cnt = 0;
+
+ if (info->speed <= 600) {
+ sleep_interval = 10;
+ reset_cnt = MX_FIFO_RESET_CNT;
+ } else {
+ sleep_interval = 1;
+ reset_cnt = MX_FIFO_RESET_CNT / 10;
+ }
+
+ /* Workaround for clear FIFO in low baudrate */
+ iowrite8(0x0f, info->ioaddr + MOXA_PUART_ADJ_CLK);
+ iowrite8(0x03, info->ioaddr + MOXA_PUART_ADJ_ENABLE);
+
+ /* clear Rx/Tx FIFO's */
+ for (i = 0; i < reset_cnt; i++) {
+ iowrite8((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
+ info->ioaddr + UART_FCR);
+ msleep(sleep_interval);
+ }
+
+ iowrite8(0x00, info->ioaddr + MOXA_PUART_ADJ_CLK);
+ iowrite8(0x02, info->ioaddr + MOXA_PUART_ADJ_ENABLE);
+ } else {
+ /* clear Rx/Tx FIFO's */
+ iowrite8((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
+ info->ioaddr + UART_FCR);
+ }
+ /* read data port to reset things */
+ (void)ioread8(info->ioaddr + UART_RX);
+
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ clear_bit(ASYNCB_INITIALIZED, &port->flags);
+}
+
+static int mxupcie_open(struct tty_struct *tty, struct file *filp)
+{
+ struct mxupcie_port *info;
+ struct mxupcie_board *board;
+ int line;
+
+ line = tty->index;
+ if (line == MXUPCIE_PORTS)
+ return 0;
+
+ if ((line < 0) || (line > MXUPCIE_PORTS))
+ return -ENODEV;
+
+ board = &mxupcie_boards[line / MXUPCIE_PORTS_PER_BOARD];
+ info = &board->ports[line % MXUPCIE_PORTS_PER_BOARD];
+
+ tty->driver_data = info;
+
+ return tty_port_open(&info->port, tty, filp);
+}
+
+static void mxupcie_close_port(struct tty_port *port)
+{
+ struct mxupcie_port *info;
+ unsigned char reg_flag;
+ unsigned long timeout;
+
+ info = container_of(port, struct mxupcie_port, port);
+
+ /*
+ * Now we wait for the transmit buffer to clear; and we notify
+ * the line discipline to only process XON/XOFF characters.
+ */
+ reg_flag = ioread8(info->ioaddr + MOXA_PUART_EFR);
+ reg_flag &= ~MOXA_EFR_AUTO_RTS;
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_EFR);
+
+ /*
+ * At this point we stop accepting input. To do this, we
+ * disable the receive line status interrupts, and tell the
+ * interrupt driver to stop checking the data ready bit in the
+ * line status register.
+ */
+ info->ier &= ~UART_IER_RLSI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+
+ /*
+ * Before we drop DTR, make sure the UART transmitter
+ * has completely drained; this is especially
+ * important if there is a transmit FIFO!
+ */
+ timeout = jiffies + HZ;
+ while (!(ioread8(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) {
+ schedule_timeout_interruptible(5);
+ if (time_after(jiffies, timeout))
+ break;
+ }
+}
+
+static void mxupcie_close(struct tty_struct *tty, struct file *filp)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ struct tty_port *port = &info->port;
+
+ if (tty->index == MXUPCIE_PORTS || info == NULL)
+ return;
+ if (tty_port_close_start(port, tty, filp) == 0)
+ return;
+
+ mutex_lock(&port->mutex);
+ mxupcie_close_port(port);
+ mxupcie_flush_buffer(tty);
+ if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (tty->termios.c_cflag & HUPCL)
+ tty_port_lower_dtr_rts(port);
+ }
+ mxupcie_shutdown(port);
+ set_bit(TTY_IO_ERROR, &tty->flags);
+ mutex_unlock(&port->mutex);
+ tty_port_close_end(port, tty);
+ tty_port_tty_set(port, NULL);
+}
+
+static int mxupcie_write(struct tty_struct *tty,
+ const unsigned char *buf, int count)
+{
+ int c, total = 0;
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ if (!info->port.xmit_buf)
+ return 0;
+
+ while (1) {
+ c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
+ SERIAL_XMIT_SIZE - info->xmit_head));
+ if (c <= 0)
+ break;
+
+ memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->xmit_head = (info->xmit_head + c) &
+ (SERIAL_XMIT_SIZE - 1);
+ info->xmit_cnt += c;
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ buf += c;
+ count -= c;
+ total += c;
+ }
+
+ if (info->xmit_cnt && !tty->stopped) {
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->ier &= ~UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ info->ier |= UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ }
+
+ return total;
+}
+
+static int mxupcie_put_char(struct tty_struct *tty, unsigned char ch)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ if (!info->port.xmit_buf)
+ return 0;
+
+ if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1)
+ return 0;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->port.xmit_buf[info->xmit_head++] = ch;
+ info->xmit_head &= SERIAL_XMIT_SIZE - 1;
+ info->xmit_cnt++;
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ if (!tty->stopped && !tty->hw_stopped) {
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->ier &= ~UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ info->ier |= UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ }
+
+ return 1;
+}
+
+
+static void mxupcie_flush_chars(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf)
+ return;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->ier &= ~UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ info->ier |= UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+}
+
+
+static int mxupcie_write_room(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ int ret;
+
+ ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
+ if (ret < 0)
+ ret = 0;
+
+ return ret;
+}
+
+static int mxupcie_get_serial_info(struct tty_struct *tty,
+ struct serial_struct *retinfo)
+{
+ struct serial_struct tmp;
+ struct mxupcie_port *info = tty->driver_data;
+
+ memset(&tmp, 0, sizeof(tmp));
+ tmp.line = tty->index;
+ tmp.port = *info->ioaddr;
+ tmp.irq = info->board->irq;
+ tmp.flags = info->port.flags;
+ tmp.baud_base = info->baud_base;
+ tmp.close_delay = info->close_delay;
+ tmp.closing_wait = info->closing_wait;
+ tmp.custom_divisor = info->custom_divisor;
+ tmp.hub6 = 0;
+
+ if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+ return -EFAULT;
+
+ return 0;
+}
+
+static int mxupcie_set_serial_info(struct tty_struct *tty,
+ struct serial_struct *new_info)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ struct tty_port *port = &info->port;
+ struct serial_struct new_serial;
+ unsigned int flags;
+ int retval = 0;
+ unsigned long sp_flags;
+
+ if (!new_info)
+ return -EFAULT;
+
+ if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
+ return -EFAULT;
+
+ if ((new_serial.irq != info->board->irq) ||
+ (new_serial.port != *info->ioaddr))
+ return -EINVAL;
+
+ flags = port->flags & ASYNC_SPD_MASK;
+
+ if (!capable(CAP_SYS_ADMIN)) {
+ if ((new_serial.baud_base != info->baud_base) ||
+ (new_serial.close_delay != info->close_delay) ||
+ ((new_serial.flags & ~ASYNC_USR_MASK) !=
+ (port->flags & ~ASYNC_USR_MASK)))
+ return -EPERM;
+
+ port->flags = ((port->flags & ~ASYNC_USR_MASK) |
+ (new_serial.flags & ASYNC_USR_MASK));
+ } else {
+ /*
+ * OK, past this point, all the error checking has been done.
+ * At this point, we start making changes.....
+ */
+ port->flags = ((port->flags & ~ASYNC_FLAGS) |
+ (new_serial.flags & ASYNC_FLAGS));
+ info->close_delay = new_serial.close_delay * HZ / 100;
+ info->closing_wait = new_serial.closing_wait * HZ / 100;
+
+ if ((new_serial.baud_base != info->baud_base) ||
+ (new_serial.custom_divisor != info->custom_divisor)) {
+
+ if (new_serial.custom_divisor == 0)
+ return -EINVAL;
+
+ info->custom_baud_rate = new_serial.baud_base /
+ new_serial.custom_divisor;
+ }
+ }
+
+ if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (flags != (port->flags & ASYNC_SPD_MASK)) {
+ spin_lock_irqsave(&info->slock, sp_flags);
+ mxupcie_change_speed(tty, NULL);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ }
+ } else {
+ retval = mxupcie_activate(port, tty);
+ if (retval == 0)
+ set_bit(ASYNCB_INITIALIZED, &port->flags);
+ }
+
+ return retval;
+}
+
+/*
+ * mx_get_lsr_info - get line status register info
+ *
+ * Purpose: Let user call ioctl() to get info when the UART physically
+ * is emptied. On bus types like RS485, the transmitter must
+ * release the bus after transmitting. This must be done when
+ * the transmit shift register is empty, not be done when the
+ * transmit holding register is empty. This functionality
+ * allows an RS485 driver to be written in user space.
+ */
+static int mxupcie_get_lsr_info(struct tty_struct *tty, unsigned int *value)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned char status;
+ unsigned int result;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ status = ioread8(info->ioaddr + UART_LSR);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
+ put_user(result, value);
+
+ return 0;
+}
+
+static void mxupcie_software_break_signal(struct tty_struct *tty,
+ unsigned char state)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned char cval, reg_flag;
+ unsigned char tx_byte = 0x01;
+ int origin_speed;
+
+ origin_speed = info->speed;
+
+ if (state == MX_BREAK_ON) {
+ cval = ioread8(info->ioaddr + UART_LCR);
+ iowrite8(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR);
+ iowrite8(0, info->ioaddr + UART_DLL);
+ iowrite8(0, info->ioaddr + UART_DLM);
+ iowrite8(cval, info->ioaddr + UART_LCR);
+
+ memcpy(info->ioaddr + MOXA_PUART_MEMTHR, &tx_byte, 1);
+
+ reg_flag = ioread8(info->ioaddr + MOXA_PUART_SFR);
+ reg_flag |= MOXA_SFR_FORCE_TX;
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_SFR);
+
+ iowrite8(ioread8(info->ioaddr + UART_LCR) | UART_LCR_SBC,
+ info->ioaddr + UART_LCR);
+ }
+
+ if (state == MX_BREAK_OFF) {
+ iowrite8(ioread8(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
+ info->ioaddr + UART_LCR);
+
+ reg_flag = ioread8(info->ioaddr + MOXA_PUART_SFR);
+ reg_flag &= ~MOXA_SFR_FORCE_TX;
+ iowrite8(reg_flag, info->ioaddr + MOXA_PUART_SFR);
+
+ iowrite8(UART_FCR_CLEAR_XMIT, info->ioaddr + UART_FCR);
+
+ mxupcie_set_baud(tty, origin_speed);
+ }
+}
+
+static void mxupcie_send_break(struct tty_struct *tty, int duration)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ set_current_state(TASK_INTERRUPTIBLE);
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ switch (info->uir) {
+ case MOXA_UIR_RS485_4W:
+ case MOXA_UIR_RS485_2W:
+ mxupcie_software_break_signal(tty, MX_BREAK_ON);
+ break;
+ case MOXA_UIR_RS232:
+ case MOXA_UIR_RS422:
+ iowrite8(ioread8(info->ioaddr + UART_LCR) | UART_LCR_SBC,
+ info->ioaddr + UART_LCR);
+ break;
+ }
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ schedule_timeout(duration);
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ switch (info->uir) {
+ case MOXA_UIR_RS485_4W:
+ case MOXA_UIR_RS485_2W:
+ mxupcie_software_break_signal(tty, MX_BREAK_OFF);
+ break;
+ case MOXA_UIR_RS232:
+ case MOXA_UIR_RS422:
+ iowrite8(ioread8(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
+ info->ioaddr + UART_LCR);
+ break;
+ }
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ set_current_state(TASK_RUNNING);
+}
+
+static int mxupcie_set_interface(struct mxupcie_port *info, unsigned char val)
+{
+ struct mxupcie_board *board = info->board;
+ unsigned char intf = 0, chip_val = 0;
+ int ret;
+
+ switch (val) {
+ case MOXA_UIR_RS232:
+ if (!(board->cinfo->flags & MX_FLAG_232))
+ return -EINVAL;
+ ret = mxupcie_set_terminator(info, MX_TERM_NONE);
+ if (ret < 0)
+ return -EINVAL;
+ case MOXA_UIR_RS422:
+ case MOXA_UIR_RS485_4W:
+ case MOXA_UIR_RS485_2W:
+ if (board->cinfo->flags & (MX_FLAG_422 | MX_FLAG_485)) {
+ info->uir = val;
+ chip_val = inb(info->uir_addr);
+
+ if (info->port_index % 2) {
+ intf = val << MOXA_UIR_EVEN_PORT_VALUE_OFFSET;
+ chip_val &= 0x0F;
+ chip_val |= intf;
+
+ } else {
+ intf = val;
+ chip_val &= 0xF0;
+ chip_val |= intf;
+ }
+
+ outb(chip_val, info->uir_addr);
+ } else {
+ return -EINVAL;
+ }
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int mxupcie_cflags_changed(struct mxupcie_port *info, unsigned long arg,
+ struct async_icount *cprev)
+{
+ struct async_icount cnow;
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&info->slock, flags);
+ cnow = info->icount;
+ spin_unlock_irqrestore(&info->slock, flags);
+
+ ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
+ ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
+ ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
+ ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
+
+ *cprev = cnow;
+
+ return ret;
+}
+
+static int mxupcie_ioctl(struct tty_struct *tty, unsigned int cmd,
+ unsigned long arg)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ int retval;
+ struct async_icount cnow;
+ int ret = 0;
+ unsigned long sp_flags;
+
+ switch (cmd) {
+ case TCSBRK:
+ retval = tty_check_change(tty);
+ if (retval)
+ return retval;
+
+ tty_wait_until_sent(tty, 0);
+
+ if (!arg)
+ mxupcie_send_break(tty, HZ / 4);
+
+ break;
+ case TCSBRKP:
+ retval = tty_check_change(tty);
+ if (retval)
+ return retval;
+
+ tty_wait_until_sent(tty, 0);
+ mxupcie_send_break(tty, arg ? arg * (HZ / 10) : HZ / 4);
+
+ break;
+ case TIOCGSERIAL:
+ ret = mxupcie_get_serial_info(tty,
+ (struct serial_struct __user *)arg);
+ break;
+ case TIOCSSERIAL:
+ ret = mxupcie_set_serial_info(tty,
+ (struct serial_struct __user *)arg);
+ break;
+ case TIOCSERGETLSR:
+ ret = mxupcie_get_lsr_info(tty, (unsigned int __user *)arg);
+ break;
+ case TIOCMIWAIT:
+ spin_lock_irqsave(&info->slock, sp_flags);
+ cnow = info->icount;
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ ret = wait_event_interruptible(info->port.delta_msr_wait,
+ mxupcie_cflags_changed(info, arg, &cnow));
+ break;
+ default:
+ ret = -ENOIOCTLCMD;
+ }
+
+ return ret;
+}
+
+static void mxupcie_throttle(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->ier &= ~UART_IER_RDI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+}
+
+static void mxupcie_unthrottle(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ info->ier |= UART_IER_RDI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+}
+
+static void mxupcie_stop(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ if (info->ier & UART_IER_THRI) {
+ info->ier &= ~UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ }
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+}
+
+static void mxupcie_start(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ if (info->xmit_cnt && info->port.xmit_buf) {
+ info->ier &= ~UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ info->ier |= UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ }
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+}
+
+static void mxupcie_set_termios(struct tty_struct *tty,
+ struct ktermios *old_termios)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ mxupcie_change_speed(tty, old_termios);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ if (old_termios &&
+ !tty_termios_hw_change(&tty->termios, old_termios) &&
+ tty->termios.c_iflag == old_termios->c_iflag) {
+ dev_dbg(tty->dev, "%s - nothing to change\n", __func__);
+ return;
+ }
+
+ if ((old_termios->c_cflag & CRTSCTS) &&
+ !(tty->termios.c_cflag & CRTSCTS)) {
+ tty->hw_stopped = 0;
+ mxupcie_start(tty);
+ }
+
+ if ((old_termios->c_iflag & IXON) &&
+ !(tty->termios.c_iflag & IXON)) {
+ tty->stopped = 0;
+ mxupcie_start(tty);
+ }
+}
+
+void mxupcie_hangup(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+
+ mxupcie_flush_buffer(tty);
+ tty_port_hangup(&info->port);
+}
+
+static void mxupcie_check_modem_status(struct tty_struct *tty,
+ int status)
+{
+ struct mxupcie_port *info = tty->driver_data;
+
+ if (status & UART_MSR_TERI)
+ info->icount.rng++;
+ if (status & UART_MSR_DDSR)
+ info->icount.dsr++;
+ if (status & UART_MSR_DDCD)
+ info->icount.dcd++;
+ if (status & UART_MSR_DCTS)
+ info->icount.cts++;
+
+ wake_up_interruptible(&info->port.delta_msr_wait);
+
+ if ((info->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
+ if (status & UART_MSR_DCD)
+ wake_up_interruptible(&info->port.open_wait);
+ else
+ tty_hangup(tty);
+ }
+
+ if (tty_port_cts_enabled(&info->port)) {
+ if (tty->hw_stopped) {
+ if (status & UART_MSR_CTS) {
+ tty->hw_stopped = 0;
+ tty_wakeup(tty);
+ }
+ } else {
+ if (!(status & UART_MSR_CTS))
+ tty->hw_stopped = 1;
+ }
+ }
+}
+
+static int mxupcie_tiocmget(struct tty_struct *tty)
+{
+ struct mxupcie_port *info;
+ unsigned char control, status;
+ unsigned long sp_flags;
+
+ info = tty->driver_data;
+
+ control = info->mcr;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ status = ioread8(info->ioaddr + UART_MSR);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
+ ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
+ ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
+ ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
+ ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
+ ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
+}
+
+static int mxupcie_tiocmset(struct tty_struct *tty,
+ unsigned int set, unsigned int clear)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+
+ if (set & TIOCM_RTS)
+ info->mcr |= UART_MCR_RTS;
+ if (set & TIOCM_DTR)
+ info->mcr |= UART_MCR_DTR;
+ if (clear & TIOCM_RTS)
+ info->mcr &= ~UART_MCR_RTS;
+ if (clear & TIOCM_DTR)
+ info->mcr &= ~UART_MCR_DTR;
+
+ iowrite8(info->mcr, info->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+
+ return 0;
+}
+
+static int mxupcie_rs_break(struct tty_struct *tty, int break_state)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+ int lcr;
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ if (break_state == -1) {
+ switch (info->uir) {
+ case MOXA_UIR_RS485_4W:
+ case MOXA_UIR_RS485_2W:
+ mxupcie_software_break_signal(tty, MX_BREAK_ON);
+ break;
+ case MOXA_UIR_RS232:
+ case MOXA_UIR_RS422:
+ lcr = ioread8(info->ioaddr + UART_LCR) | UART_LCR_SBC;
+ iowrite8(lcr, info->ioaddr + UART_LCR);
+ break;
+ }
+ } else {
+ switch (info->uir) {
+ case MOXA_UIR_RS485_4W:
+ case MOXA_UIR_RS485_2W:
+ mxupcie_software_break_signal(tty, MX_BREAK_OFF);
+ break;
+ case MOXA_UIR_RS232:
+ case MOXA_UIR_RS422:
+ lcr = ioread8(info->ioaddr + UART_LCR) & ~UART_LCR_SBC;
+ iowrite8(lcr, info->ioaddr + UART_LCR);
+ break;
+ }
+ }
+
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ return 0;
+}
+
+static void mxupcie_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned long sp_flags;
+ unsigned long orig_jiffies, char_time;
+ int lsr;
+
+ orig_jiffies = jiffies;
+ /*
+ * Set the check interval to be 1/5 of the estimated time to
+ * send a single character, and make it at least 1. The check
+ * interval should also be less than the timeout.
+ *
+ * Note: we have to use pretty tight timings here to satisfy
+ * the NIST-PCTS.
+ */
+ char_time = (info->timeout - HZ / 50) / MX_TX_FIFO_SIZE;
+ char_time = char_time / 5;
+
+ if (char_time == 0)
+ char_time = 1;
+
+ if (timeout && timeout < char_time)
+ char_time = timeout;
+ /*
+ * If the transmitter hasn't cleared in twice the approximate
+ * amount of time to send the entire FIFO, it probably won't
+ * ever clear. This assumes the UART isn't doing flow
+ * control, which is currently the case. Hence, if it ever
+ * takes longer than info->timeout, this is probably due to a
+ * UART bug of some kind. So, we clamp the timeout parameter at
+ * 2*info->timeout.
+ */
+
+ if (!timeout || timeout > 2 * info->timeout)
+ timeout = 2 * info->timeout;
+
+ dev_dbg(tty->dev, "%s(%d) - check=%lu", __func__, timeout, char_time);
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ while (!((lsr = ioread8(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) {
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ dev_dbg(tty->dev, "lsr = %d (jiff=%lu)", lsr, jiffies);
+ schedule_timeout_interruptible(char_time);
+ spin_lock_irqsave(&info->slock, sp_flags);
+
+ if (signal_pending(current))
+ break;
+
+ if (timeout && time_after(jiffies, orig_jiffies + timeout))
+ break;
+ }
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+ set_current_state(TASK_RUNNING);
+
+ dev_dbg(tty->dev, "lsr = %d (jiff=%lu), done", lsr, jiffies);
+}
+
+static void mxupcie_rx_chars(struct tty_struct *tty,
+ int *status)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ unsigned char ch, gdl = 0;
+ int cnt = 0;
+ int recv_room;
+ int max = 256;
+ unsigned long flags;
+
+ if (*status & UART_LSR_SPECIAL)
+ goto intr_old;
+
+ recv_room = tty_buffer_request_room(&info->port, MX_RX_FIFO_SIZE);
+ if (recv_room) {
+ gdl = ioread8(info->ioaddr + MOXA_PUART_RCNT);
+
+ if (gdl > recv_room)
+ gdl = recv_room;
+
+ if (gdl) {
+ tty_insert_flip_string(
+ &info->port,
+ info->ioaddr + MOXA_PUART_MEMRBR, gdl);
+
+ cnt = gdl;
+ }
+ } else {
+ set_bit(TTY_THROTTLED, &tty->flags);
+ }
+
+ goto end_intr;
+
+intr_old:
+ do {
+ if (max-- < 0)
+ break;
+
+ ch = ioread8(info->ioaddr + UART_RX);
+
+ if (*status & UART_LSR_SPECIAL) {
+ if (*status & UART_LSR_BI) {
+ flags = TTY_BREAK;
+ info->icount.brk++;
+
+ if (info->port.flags & ASYNC_SAK)
+ do_SAK(tty);
+ } else if (*status & UART_LSR_PE) {
+ flags = TTY_PARITY;
+ info->icount.parity++;
+ } else if (*status & UART_LSR_FE) {
+ flags = TTY_FRAME;
+ info->icount.frame++;
+ } else if (*status & UART_LSR_OE) {
+ flags = TTY_OVERRUN;
+ info->icount.overrun++;
+ } else {
+ flags = TTY_BREAK;
+ }
+
+ } else {
+ flags = 0;
+ }
+
+ tty_insert_flip_char(&info->port, ch, flags);
+ cnt++;
+
+ *status = ioread8(info->ioaddr + UART_LSR);
+ } while (*status & UART_LSR_DR);
+
+end_intr:
+ tty_flip_buffer_push(&info->port);
+
+ info->icount.rx += cnt;
+}
+
+static void mxupcie_tx_chars(struct tty_struct *tty)
+{
+ struct mxupcie_port *info = tty->driver_data;
+ int cnt;
+ int tx_cnt;
+
+ if (info->port.xmit_buf == NULL)
+ return;
+
+ if (info->xmit_cnt == 0 || tty->stopped) {
+ dev_dbg(tty->dev, "%s: tty stopped\n", __func__);
+ info->ier &= ~UART_IER_THRI;
+ iowrite8(info->ier, info->ioaddr + UART_IER);
+ return;
+ }
+
+ cnt = info->xmit_cnt;
+
+ tx_cnt = MX_TX_FIFO_SIZE - ioread8(info->ioaddr + MOXA_PUART_TCNT);
+
+ cnt = min(info->xmit_cnt,
+ min(tx_cnt, (int)(SERIAL_XMIT_SIZE - info->xmit_tail)));
+ if (cnt) {
+ memcpy(info->ioaddr + MOXA_PUART_MEMTHR,
+ info->port.xmit_buf + info->xmit_tail, cnt);
+ info->xmit_tail += cnt;
+ info->xmit_tail &= (SERIAL_XMIT_SIZE - 1);
+ info->xmit_cnt -= cnt;
+ }
+
+ info->icount.tx += cnt;
+
+ if (info->xmit_cnt < WAKEUP_CHARS)
+ tty_wakeup(tty);
+}
+
+static int mxupcie_carrier_raised(struct tty_port *port)
+{
+ struct mxupcie_port *info;
+
+ info = container_of(port, struct mxupcie_port, port);
+ return (ioread8(info->ioaddr + UART_MSR) & UART_MSR_DCD) ? 1 : 0;
+}
+
+static void mxupcie_dtr_rts(struct tty_port *port, int raise)
+{
+ struct mxupcie_port *info;
+ unsigned long sp_flags;
+ int mcr;
+
+ info = container_of(port, struct mxupcie_port, port);
+
+ spin_lock_irqsave(&info->slock, sp_flags);
+ mcr = ioread8(info->ioaddr + UART_MCR);
+ if (raise)
+ mcr |= UART_MCR_DTR | UART_MCR_RTS;
+ else
+ mcr &= ~(UART_MCR_DTR | UART_MCR_RTS);
+
+ iowrite8(mcr, info->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&info->slock, sp_flags);
+}
+
+static const struct tty_port_operations mxupcie_port_ops = {
+ .carrier_raised = mxupcie_carrier_raised,
+ .dtr_rts = mxupcie_dtr_rts,
+ .activate = mxupcie_activate,
+ .shutdown = mxupcie_shutdown
+};
+
+static irqreturn_t mxupcie_interrupt(int irq, void *dev_id)
+{
+ int lsr, iir, i;
+ struct mxupcie_board *board;
+ struct mxupcie_port *info;
+ int max, msr;
+ int pass_counter = 0;
+ int int_cnt;
+ int handled = 0;
+ int vect_flag;
+ struct tty_struct *tty;
+
+ board = NULL;
+ for (i = 0; i < MXUPCIE_BOARDS; i++) {
+ if (dev_id == &mxupcie_boards[i]) {
+ board = dev_id;
+ break;
+ }
+ }
+
+ if (i == MXUPCIE_BOARDS)
+ goto irq_stop;
+
+ if (board == NULL)
+ goto irq_stop;
+
+ max = board->cinfo->nports;
+ pass_counter = 0;
+
+ do {
+ vect_flag = 0;
+
+ for (i = 0; i < max; i++) {
+ info = &board->ports[i];
+ int_cnt = 0;
+
+ do {
+ iir = ioread8(info->ioaddr + UART_IIR);
+ if (iir == MOXA_IIR_NO_INT) {
+ vect_flag++;
+ break;
+ }
+
+ tty = tty_port_tty_get(&info->port);
+ if (!tty) {
+ lsr = ioread8(info->ioaddr + UART_LSR);
+ iowrite8(0x27, info->ioaddr + UART_FCR);
+ ioread8(info->ioaddr + UART_MSR);
+ break;
+ }
+
+ handled = 1;
+
+ spin_lock(&info->slock);
+ lsr = ioread8(info->ioaddr + UART_LSR);
+
+ if (iir & MOXA_IIR_RDI) {
+ lsr &= info->read_status_mask;
+ if (lsr & UART_LSR_DR)
+ mxupcie_rx_chars(tty, &lsr);
+ }
+
+ msr = ioread8(info->ioaddr + UART_MSR);
+ if (msr & UART_MSR_ANY_DELTA)
+ mxupcie_check_modem_status(tty, msr);
+
+ if (iir & MOXA_IIR_THRI) {
+ if (lsr & UART_LSR_THRE)
+ mxupcie_tx_chars(tty);
+ }
+
+ spin_unlock(&info->slock);
+ tty_kref_put(tty);
+ } while (int_cnt++ < MXUPCIE_ISR_PASS_LIMIT);
+ }
+
+ if (vect_flag == max)
+ break;
+
+ } while (pass_counter++ < MXUPCIE_ISR_PASS_LIMIT);
+
+irq_stop:
+ return IRQ_RETVAL(handled);
+}
+
+int mxupcie_initbrd(struct mxupcie_board *board, struct pci_dev *pdev)
+{
+ int err;
+ int i;
+ struct mxupcie_port *info;
+ unsigned long addr;
+ int temp_interface = 0;
+
+ for (i = 0; i < board->cinfo->nports; i++) {
+ info = &board->ports[i];
+ tty_port_init(&info->port);
+ info->board = board;
+ info->port_index = board->index + i;
+ info->uir = 0;
+
+ if (board->cinfo->nports == 4 && i == MX_PORT4)
+ addr = board->iobar3_addr + MOXA_UIR_OFFSET + 3;
+ else
+ addr = board->iobar3_addr + MOXA_UIR_OFFSET + (i / 2);
+
+ info->port.ops = &mxupcie_port_ops;
+ info->uir_addr = addr;
+ info->custom_divisor = info->baud_base * 16;
+ info->close_delay = 5 * HZ / 10;
+ info->closing_wait = 30 * HZ;
+ info->speed = 9600;
+ spin_lock_init(&info->slock);
+
+ outb(MOXA_GPIO_SET_ALL_OUTPUT,
+ board->iobar3_addr + MOXA_PUART_GPIO_EN);
+
+ mxupcie_init_terminator(info);
+
+ if (!interface) {
+ if (board->cinfo->flags & MX_FLAG_232)
+ temp_interface = MOXA_UIR_RS232;
+ else
+ temp_interface = MOXA_UIR_RS422;
+ } else {
+ temp_interface = interface;
+ }
+
+ mxupcie_set_interface(info, temp_interface);
+
+ /* before set INT ISR, disable all int */
+ iowrite8(ioread8(info->ioaddr + UART_IER) & 0xf0,
+ info->ioaddr + UART_IER);
+ }
+
+ err = request_irq(board->irq, mxupcie_interrupt, IRQF_SHARED, "mxupcie",
+ board);
+ if (err) {
+ dev_err(&pdev->dev, "irq %d may be in conflict\n", board->irq);
+ return err;
+ }
+
+ return 0;
+}
+
+static const struct tty_operations mxupcie_ops = {
+ .open = mxupcie_open,
+ .close = mxupcie_close,
+ .write = mxupcie_write,
+ .put_char = mxupcie_put_char,
+ .flush_chars = mxupcie_flush_chars,
+ .write_room = mxupcie_write_room,
+ .chars_in_buffer = mxupcie_chars_in_buffer,
+ .flush_buffer = mxupcie_flush_buffer,
+ .ioctl = mxupcie_ioctl,
+ .throttle = mxupcie_throttle,
+ .unthrottle = mxupcie_unthrottle,
+ .stop = mxupcie_stop,
+ .start = mxupcie_start,
+ .set_termios = mxupcie_set_termios,
+ .hangup = mxupcie_hangup,
+ .tiocmget = mxupcie_tiocmget,
+ .tiocmset = mxupcie_tiocmset,
+ .break_ctl = mxupcie_rs_break,
+ .wait_until_sent = mxupcie_wait_until_sent,
+};
+
+static int mxupcie_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct mxupcie_board *board;
+ unsigned char *ioaddress;
+ unsigned long iobar_address;
+ struct device *tty_dev;
+ int i, err = 0;
+
+ for (i = 0; i < MXUPCIE_BOARDS; i++) {
+ if (!mxupcie_boards[i].cinfo)
+ break;
+ }
+
+ if (i >= MXUPCIE_BOARDS) {
+ dev_err(&pdev->dev, "too many boards found: %d >= %d\n",
+ i, MXUPCIE_BOARDS);
+ goto err;
+ }
+
+ board = &mxupcie_boards[i];
+ board->index = i * MXUPCIE_PORTS_PER_BOARD;
+
+ dev_info(&pdev->dev, "found MOXA %s board(busno=%d,devno=%d)\n",
+ mxupcie_cards[ent->driver_data].name,
+ pdev->bus->number, PCI_SLOT(pdev->devfn));
+
+ memset(&board->ports, '\0', sizeof(board->ports));
+ err = pci_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "pci_enable_device fail\n");
+ goto err;
+ }
+
+ /* io address */
+ if (!request_mem_region(pci_resource_start(pdev, 1),
+ pci_resource_len(pdev, 1),
+ "mxupcie(MEM)")) {
+ err = -EBUSY;
+ goto err_dis;
+ }
+
+ ioaddress = ioremap(pci_resource_start(pdev, 1),
+ pci_resource_len(pdev, 1));
+ if (!ioaddress) {
+ err = -ENOMEM;
+ goto err_rel_mem;
+ }
+
+ iobar_address = pci_resource_start(pdev, 2);
+ if (!request_region(pci_resource_start(pdev, 2),
+ pci_resource_len(pdev, 2),
+ "mxupcie(IOBAR3)")) {
+ err = -EBUSY;
+ goto err_unmap;
+ }
+
+ board->cinfo = &mxupcie_cards[ent->driver_data];
+ for (i = 0; i < board->cinfo->nports; i++) {
+ unsigned char *addr;
+
+ board->ports[i].baud_base = 921600;
+ board->ports[i].max_baud = 921600;
+
+ if (board->cinfo->nports == 4 && i == MX_PORT4)
+ addr = ioaddress + (MX_PORT8 * MX_PUART_SIZE);
+ else
+ addr = ioaddress + (i * MX_PUART_SIZE);
+
+ board->ports[i].ioaddr = addr;
+ }
+
+ board->irq = pdev->irq;
+ board->iobar3_addr = iobar_address;
+
+ err = mxupcie_initbrd(board, pdev);
+ if (err)
+ goto err_zero;
+
+ for (i = 0; i < board->cinfo->nports; i++) {
+ dev_info(&pdev->dev, "register ttyMUE%d\n", board->index + i);
+ tty_dev = tty_port_register_device(&board->ports[i].port,
+ mx_drv,
+ board->index + i,
+ &pdev->dev);
+ if (IS_ERR(tty_dev)) {
+ err = PTR_ERR(tty_dev);
+ for (; i > 0; i--)
+ tty_unregister_device(mx_drv,
+ board->index + i - 1);
+ goto err_relboard;
+ }
+ }
+
+ pci_set_drvdata(pdev, board);
+
+ return 0;
+
+err_relboard:
+ for (i = 0; i < board->cinfo->nports; i++)
+ tty_port_destroy(&board->ports[i].port);
+ free_irq(board->irq, board);
+err_zero:
+ board->cinfo = NULL;
+ release_region(pci_resource_start(pdev, 2),
+ pci_resource_len(pdev, 2));
+err_unmap:
+ iounmap(ioaddress);
+err_rel_mem:
+ release_mem_region(pci_resource_start(pdev, 1),
+ pci_resource_len(pdev, 1));
+err_dis:
+ pci_disable_device(pdev);
+err:
+ return err;
+}
+
+static void mxupcie_pci_remove(struct pci_dev *pdev)
+{
+ struct mxupcie_board *board = pci_get_drvdata(pdev);
+ int i;
+
+ for (i = 0; i < board->cinfo->nports; i++) {
+ tty_unregister_device(mx_drv, board->index + i);
+ tty_port_destroy(&board->ports[i].port);
+ }
+
+ free_irq(board->irq, board);
+
+ iounmap(board->ports[1].ioaddr);
+ release_mem_region(pci_resource_start(pdev, 1),
+ pci_resource_len(pdev, 1));
+ release_region(pci_resource_start(pdev, 2), pci_resource_len(pdev, 2));
+
+ board->cinfo = NULL;
+}
+
+static struct pci_driver mxupcie_pci_driver = {
+ .name = "mxupcie",
+ .id_table = mxupcie_pcibrds,
+ .probe = mxupcie_pci_probe,
+ .remove = mxupcie_pci_remove
+};
+
+static int __init mxupcie_module_init(void)
+{
+ int err = 0;
+
+ mx_drv = alloc_tty_driver(MXUPCIE_PORTS + 1);
+ if (!mx_drv)
+ return -ENOMEM;
+
+ /* Initialize the tty_driver structure */
+ mx_drv->name = "ttyMUE";
+ mx_drv->major = 0;
+ mx_drv->minor_start = 0;
+ mx_drv->type = TTY_DRIVER_TYPE_SERIAL;
+ mx_drv->subtype = SERIAL_TYPE_NORMAL;
+ mx_drv->init_termios = tty_std_termios;
+ mx_drv->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+ mx_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+ tty_set_operations(mx_drv, &mxupcie_ops);
+
+ err = tty_register_driver(mx_drv);
+ if (err) {
+ pr_err("failed to register tty driver: %d\n", err);
+ goto err_put;
+ }
+
+ err = pci_register_driver(&mxupcie_pci_driver);
+ if (err) {
+ pr_err("failed to register pci driver: %d\n", err);
+ goto err_unr;
+ }
+
+ return 0;
+err_unr:
+ tty_unregister_driver(mx_drv);
+err_put:
+ put_tty_driver(mx_drv);
+
+ return err;
+}
+
+static void __exit mxupcie_module_exit(void)
+{
+ pci_unregister_driver(&mxupcie_pci_driver);
+
+ tty_unregister_driver(mx_drv);
+ put_tty_driver(mx_drv);
+}
+
+module_init(mxupcie_module_init);
+module_exit(mxupcie_module_exit);
+
+MODULE_AUTHOR("Mathieu OTHACEHE");
+MODULE_DESCRIPTION("MOXA SmartIO MUE driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/mxupcie.h b/drivers/tty/mxupcie.h
new file mode 100644
index 0000000..706cd70
--- /dev/null
+++ b/drivers/tty/mxupcie.h
@@ -0,0 +1,129 @@
+#ifndef _MXUPCIE_H
+#define _MXUPCIE_H
+
+/* The definition of linear baud rate */
+#define FREQUENCY 14745600
+#define MAXDIVISOR 255
+#define MAXSEQUENCE 46
+#define MINSEQUENCE 4
+#define MAX_SCR 12
+#define MIN_SCR 0
+#define MAX_CPRN 7
+#define MIN_CPRN 0
+#define MIN_CPRM 1
+#define MAX_CPRM 2
+
+#define MXUPCIE_BOARDS 4 /* Max. boards */
+#define MXUPCIE_PORTS 32 /* Max. ports */
+#define MXUPCIE_PORTS_PER_BOARD 8 /* Max. ports per board*/
+#define MXUPCIE_ISR_PASS_LIMIT 99999L
+
+#define WAKEUP_CHARS 256
+
+#define UART_LSR_SPECIAL 0x1E
+
+/*
+ * Define the Moxa PCI vendor and device IDs.
+ */
+#define MOXA 0x1393
+#define PCI_DEVICE_ID_CP102E 0x1024
+#define PCI_DEVICE_ID_CP102EL 0x1025
+#define PCI_DEVICE_ID_CP132EL 0x1322
+#define PCI_DEVICE_ID_CP114EL 0x1144
+#define PCI_DEVICE_ID_CP104EL_A 0x1045
+#define PCI_DEVICE_ID_CP168EL_A 0x1683
+#define PCI_DEVICE_ID_CP118EL_A 0x1182
+#define PCI_DEVICE_ID_CP118E_A_I 0x1183
+#define PCI_DEVICE_ID_CP138E_A 0x1381
+#define PCI_DEVICE_ID_CP134EL_A 0x1342
+#define PCI_DEVICE_ID_CP116E_A_A 0x1160
+#define PCI_DEVICE_ID_CP116E_A_B 0x1161
+
+#define MOXA_PUART_SFR 0x07
+#define MOXA_PUART_EFR 0x0A
+#define MOXA_PUART_XON1 0x0B
+#define MOXA_PUART_XON2 0x0C
+#define MOXA_PUART_XOFF1 0x0D
+#define MOXA_PUART_XOFF2 0x0E
+#define MOXA_PUART_ACR 0x0F
+#define MOXA_PUART_TTL 0x10
+#define MOXA_PUART_RTL 0x11
+#define MOXA_PUART_FCL 0x12
+#define MOXA_PUART_FCH 0x13
+#define MOXA_PUART_CPR 0x14
+#define MOXA_PUART_RCNT 0x15
+#define MOXA_PUART_LSRCNT 0x15
+#define MOXA_PUART_TCNT 0x16
+#define MOXA_PUART_SCR 0x16
+#define MOXA_PUART_GLSR 0x17
+#define MOXA_PUART_MEMRBR 0x100
+#define MOXA_PUART_MEMTHR 0x100
+#define MOXA_PUART_0UIR 0x04
+#define MOXA_PUART_1UIR 0x04
+#define MOXA_PUART_2UIR 0x05
+#define MOXA_PUART_3UIR 0x05
+#define MOXA_PUART_4UIR 0x06
+#define MOXA_PUART_5UIR 0x06
+#define MOXA_PUART_6UIR 0x07
+#define MOXA_PUART_7UIR 0x07
+#define MOXA_PUART_GPIO_IN 0x08
+#define MOXA_PUART_GPIO_EN 0x09
+#define MOXA_PUART_GPIO_OUT 0x0A
+#define MOXA_PUART_LSB 0x08
+#define MOXA_PUART_MSB 0x09
+
+#define MOXA_PUART_ADJ_CLK 0x24
+#define MOXA_PUART_ADJ_ENABLE 0x25
+
+#define MOXA_SFR_FORCE_TX 0x01
+#define MOXA_SFR_950 0x20
+#define MOXA_SFR_ENABLE_TCNT 0x80
+
+#define MOXA_EFR_TX_SW 0x02
+#define MOXA_EFR_RX_SW 0x08
+#define MOXA_EFR_ENHANCE 0x10
+#define MOXA_EFR_AUTO_RTS 0x40
+#define MOXA_EFR_AUTO_CTS 0x80
+
+#define MOXA_IIR_NO_INT 0xC1
+#define MOXA_IIR_RLSI 0xC6
+#define MOXA_IIR_RDI 0x04
+#define MOXA_IIR_THRI 0x02
+
+#define MOXA_TTL_1 0x01
+#define MOXA_RTL_1 0x01
+#define MOXA_RTL_96 0x60
+#define MOXA_RTL_120 0x78
+#define MOXA_FCL_16 0x10
+#define MOXA_FCH_96 0x60
+#define MOXA_FCH_110 0x6E
+#define MOXA_FCH_120 0x78
+
+#define MOXA_UIR_RS232 0x00
+#define MOXA_UIR_RS422 0x01
+#define MOXA_UIR_RS485_4W 0x0B
+#define MOXA_UIR_RS485_2W 0x0F
+#define MOXA_UIR_OFFSET 0x04
+#define MOXA_UIR_EVEN_PORT_VALUE_OFFSET 4
+
+#define MX_FLAG_232 BIT(0)
+#define MX_FLAG_422 BIT(1)
+#define MX_FLAG_485 BIT(2)
+
+#define MOXA_GPIO_SET_ALL_OUTPUT 0x0F
+#define MOXA_GPIO_OUTPUT_VALUE_OFFSET 16
+
+#define MX_TERM_NONE 0x00
+#define MX_TERM_120 0x01
+
+#define MX_PORT4 3
+#define MX_PORT8 7
+#define MX_TX_FIFO_SIZE 128
+#define MX_RX_FIFO_SIZE 128
+#define MX_PUART_SIZE 0x200
+#define MX_BREAK_ON 0x01
+#define MX_BREAK_OFF 0x00
+
+#define MX_FIFO_RESET_CNT 100
+
+#endif
--
2.6.4