Re: [RFC 3/3] CMDQ: Mediatek CMDQ driver

From: Daniel Kurtz
Date: Fri Jan 29 2016 - 08:16:36 EST


On Fri, Jan 29, 2016 at 8:24 PM, Horng-Shyang Liao <hs.liao@xxxxxxxxxxxx> wrote:
> On Fri, 2016-01-29 at 16:42 +0800, Daniel Kurtz wrote:
>> On Fri, Jan 29, 2016 at 3:39 PM, Horng-Shyang Liao <hs.liao@xxxxxxxxxxxx> wrote:
>> > Hi Dan,
>> >
>> > Many thanks for your comments and time.
>> > I reply my plan inline.
>> >
>> >
>> > On Thu, 2016-01-28 at 12:49 +0800, Daniel Kurtz wrote:
>> >> Hi HS,
>> >>
>> >> Sorry for the delay. It is hard to find time to review a >3700 line
>> >> driver :-o in detail....
>> >>
>> >> Some review comments inline, although I still do not completely
>> >> understand how all that this driver does and how it works.
>> >> I'll try to find time to go through this driver in detail again next
>> >> time you post it for review.
>> >>
>> >> On Tue, Jan 19, 2016 at 9:14 PM, <hs.liao@xxxxxxxxxxxx> wrote:
>> >> > From: HS Liao <hs.liao@xxxxxxxxxxxx>
>> >> >
>> >> > This patch is first version of Mediatek Command Queue(CMDQ) driver. The
>> >> > CMDQ is used to help read/write registers with critical time limitation,
>> >> > such as updating display configuration during the vblank. It controls
>> >> > Global Command Engine (GCE) hardware to achieve this requirement.
>> >> > Currently, CMDQ only supports display related hardwares, but we expect
>> >> > it can be extended to other hardwares for future requirements.
>> >> >
>> >> > Signed-off-by: HS Liao <hs.liao@xxxxxxxxxxxx>
>> >>
>> >> [snip]
>> >>
>> >> > diff --git a/drivers/soc/mediatek/mtk-cmdq.c b/drivers/soc/mediatek/mtk-cmdq.c
>> >> > new file mode 100644
>> >> > index 0000000..7570f00
>> >> > --- /dev/null
>> >> > +++ b/drivers/soc/mediatek/mtk-cmdq.c
>
> [snip]
>
>> >> > +static const struct cmdq_subsys g_subsys[] = {
>> >> > + {0x1400, 1, "MMSYS"},
>> >> > + {0x1401, 2, "DISP"},
>> >> > + {0x1402, 3, "DISP"},
>> >>
>> >> This isn't going to scale. These addresses could be different on
>> >> different chips.
>> >> Instead of a static table like this, we probably need specify to the
>> >> connection between gce and other devices via devicetree phandles, and
>> >> then use the phandles to lookup the corresponding device address
>> >> range.
>> >
>> > I will define them in device tree.
>> > E.g.
>> > cmdq {
>> > reg_domain = 0x14000000, 0x14010000, 0x14020000
>> > }
>>
>> The devicetree should only model hardware relationships, not software
>> considerations.
>>
>> Is the hardware constraint here for using gce with various other
>> hardware blocks? I think we already model this by only providing a
>> gce phandle in the device tree nodes for those devices that can use
>> gce.
>>
>> Looking at the driver closer, as far as I can tell, the whole subsys
>> concept is a purely software abstraction, and only used to debug the
>> CMDQ_CODE_WRITE command. In fact, AFAICT, everything would work fine
>> if we just completely removed the 'subsys' concept, and just passed
>> through the raw address provided by the driver.
>>
>> So, I recommend just removing 'subsys' completely from the driver -
>> from this array, and in the masks.
>>
>> Instead, if there is an error on the write command, just print the
>> address that fails. There are other ways to deduce the subsystem from
>> a physical address.
>>
>> Thanks,
>>
>> -Dan
>
> Hi Dan,
>
> Subsys is not just for debug.
> Its main purpose is to transfer CPU address to GCE address.
> Let me explain it by "write" op,
> I list a code segment from cmdq_rec_append_command().
>
> case CMDQ_CODE_WRITE:
> subsys = cmdq_subsys_from_phys_addr(cqctx, arg_a);
> if (subsys < 0) {
> dev_err(dev,
> "unsupported memory base address 0x%08x\n",
> arg_a);
> return -EFAULT;
> }
>
> *cmd_ptr++ = arg_b;
> *cmd_ptr++ = (CMDQ_CODE_WRITE << CMDQ_OP_CODE_SHIFT) |
> (arg_a & CMDQ_ARG_A_WRITE_MASK) |
> ((subsys & CMDQ_SUBSYS_MASK) << CMDQ_SUBSYS_SHIFT);
> break;
>
> Subsys is mapped from physical address via cmdq_subsys_from_phys_addr(),
> and then it becomes part of GCE command via ((subsys & CMDQ_SUBSYS_MASK)
> << CMDQ_SUBSYS_SHIFT) .
> Only low bits of physical address are the same as GCE address.
> We can get it by (arg_a & CMDQ_ARG_A_WRITE_MASK).
> MASK is used to define how many bits are valid for this op.
> So, GCE address = subsys + valid low bits.

How are these upper bits of the "GCE address" defined?
In other words, for a given SoC, how is the mapping between physical
io addresses to GCE addresses defined?
Is this mapping fixed by hardware?
Does it vary for different SoCs?

-Dan

> That's why we need to know the mapping between the range of physical
> address and subsys.
> Please guide us a better way to code such requirement.
> Thanks for your help.
>
> Thanks,
> HS Liao
>