Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support

From: Anand Moon
Date: Tue Oct 13 2015 - 23:58:49 EST


hi Krzysztof,

On 14 October 2015 at 05:29, Krzysztof Kozlowski
<k.kozlowski@xxxxxxxxxxx> wrote:
> On 14.10.2015 01:27, Anand Moon wrote:
>> Hi Krzysztof,
>>
>> On 13 October 2015 at 09:13, Krzysztof Kozlowski
>> <k.kozlowski@xxxxxxxxxxx> wrote:
>>>
>>> On 13.10.2015 12:08, Anand Moon wrote:
>>>> Hi Krzysztof,
>>>>
>>>> On 13 October 2015 at 05:44, Krzysztof Kozlowski
>>>> <k.kozlowski@xxxxxxxxxxx> wrote:
>>>>> On 13.10.2015 00:32, Anand Moon wrote:
>>>>>> Hi Krzysztof,
>>>>>>
>>>>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski
>>>>>> <k.kozlowski@xxxxxxxxxxx> wrote:
>>>>>>> On 12.10.2015 00:46, Anand Moon wrote:
>>>>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104)
>>>>>>>
>>>>>>> This description is not entirely correct. The MMC driver already
>>>>>>> supports these UHS speeds (you did not any code) so you rather enabled
>>>>>>> it (description of bindings says "is supported").
>>>>>>>
>>>>>>> You mentioned DDR50 but I don't see respective property below.
>>>>>>>
>>>>>>> How do you know that these modes are really supported? I don't know. Can
>>>>>>> you convince me?
>>>>>>
>>>>>> Setting this DDR50 capability give me this error. That's the reason to
>>>>>> drop this capability.
>>>>>
>>>>> But you mentioned it in commit message! "Added support for UHS-I ...
>>>>> (DDR50)"
>>>>>
>>>>> In the same time dropping DDR50 is not an sufficient proof that "SDR50
>>>>> and SDR104 are really supported".
>>>>>
>>>>
>>>> These changes are related to the microSD card capabilities.
>>>> So SDR50 have better frequency over DDR50. On the same Sandisk card.
>>>>
>>>> When the card select the capability for DDR50
>>>> ---------------------------------------------------
>>>> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
>>>> req 50000000Hz, actual 50000000HZ div = 0)
>>>> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa
>>>> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>>>> [ 4.009179] mmcblk0: error -110 sending status command, retrying
>>>> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd
>>>> response 0x900, card status 0x900
>>>> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8,
>>>> cmd response 0x900, card status 0x0
>>>> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
>>>> req 400000Hz, actual 396825HZ div = 63)
>>>> [ 4.067770] Console: switching to colour frame buffer device 274x77
>>>> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
>>>> req 50000000Hz, actual 50000000HZ div = 0)
>>>> [ 4.099692] mmc1: tried to reset card
>>>> [ 4.101332] mmcblk0: p1 p2
>>>>
>>>>
>>>> When the card select the capability for SDR50
>>>> ---------------------------------------------------------------------------------
>>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req
>>>> 100000000Hz, actual 100000000HZ div = 0)
>>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
>>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>>>> [ 2.461743] mmcblk0: p1 p2
>>>>
>>>> Which will relate to better read/write speed.
>>>
>>> Which is not an answer to my question. To none of my previous questions.
>>>
>>
>> Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50,
>> sd-uhs-sdr104) help tune speed supported for mmc
>>
>> I have tired to compare the speed on high speed UHS-I vs ultra high
>> speed UHS-I using izone utility.
>>
>> [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
>> req 50000000Hz, actual 50000000HZ div = 0)
>> [ 2.572609] mmc1: new high speed SDHC card at address aaaa
>>
>> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k
>> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls
>> Output is in kBytes/sec
>> Time Resolution = 0.000001 seconds.
>> Processor cache size set to 32 kBytes.
>> Processor cache line size set to 64 bytes.
>> File stride size set to 17 * record size.
>> random
>> random bkwd record stride
>> kB reclen write rewrite read reread read
>> write read rewrite read fwrite frewrite fread
>> freread
>> 10240 4 1631 0 6556 0 5538 982
>> 10240 64 8828 0 18897 0 17994 303
>> 10240 128 6269 0 20670 0 20128 1096
>> ---------------------------------------------------------------------------------------------------------
>> [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot
>> req 100000000Hz, actual 100000000HZ div = 0)
>> [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
>>
>> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k
>> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls
>> Output is in kBytes/sec
>> Time Resolution = 0.000001 seconds.
>> Processor cache size set to 32 kBytes.
>> Processor cache line size set to 64 bytes.
>> File stride size set to 17 * record size.
>> random
>> random bkwd record stride
>> kB reclen write rewrite read reread read
>> write read rewrite read fwrite frewrite fread
>> freread
>> 10240 4 1809 0 7507 0 5233 859
>> 10240 64 11622 0 31250 0 28072 516
>> 10240 128 4320 0 34417 0 32509 1148
>>
>> My observation is that their slight increase in read/write operation.
>>
>> Hope I have tried to answer you query. If I am wrong please let me know.
>
> Nope, that did not answer my query. You gave some performance benchmarks
> but my question was not about the speed of anything. The question is
> (once again):
> How do you know that these modes are really supported?
>
> You are marking the *host* as supporting these modes. Please provide
> information that host supports them *really*, not by experimenting "oh,
> it seems to work now, maybe it will work always".
>
> Usually vendors, if their products implement some kind of
> specification/protocol, they mark the products as "compatible with XYZ" etc.

I found this link from hardkernel website which specify the interface support

http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141578491347

Manufacturer Part Number : Sandisk SDSDQAD-016G
Interface : UHS-1 SDR50

I don't know much internal specification of the Odroid XU3/XU4 Boards.

I am not sure if it will support host will sd-uhs-sdr104, but it will
be compatible for sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50.

-Anand Moon

>
> Best regards,
> Krzysztof
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/