[PATCH v4 0/6] mtd: nand: vf610_nfc: Freescale NFC for VF610

From: Stefan Agner
Date: Wed Mar 25 2015 - 12:28:46 EST


This adds support for Freescale NAND flash controller (NFC) found on
various devices such as Vybrid (VF610), MPC5125, MCF54418 (ColdFire)
and Kinetis K70.

The patchset is based on the patchset by Bill Pringlemeir, see:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/295419

A variant of this driver is in upstream U-Boot now. During this
process, various points have been discussed and changed. Those
changes are also incorporated in this patchset, including the
change to the name "vf610_nfc" (discussion in first patchset).
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/192465
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/193142
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/193351
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/195441
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/195513

MTD tests worked, except mtd_nandecctest.ko: The test stopped
already after changing the first bit. I guess this is due to not
properly working raw page read/write implementation. However,
implementing those functions is not feasible since ECC is always
done on-the-fly.

Performance keypoints (slightly less for page write/reads):
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 3531 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 12953 KiB/s

Changes since v3:
- Make the driver selectable when COMPILE_TEST is set
- Fix compile error due to superfluous ECC_STATUS configuration in initial
patch (without ECC correction ECC_STATUS does not need to be configured)
- Remove custom BBT pattern and switch to in-band BBT in the initial patch
- Include two bug fixes, for details see the corresponding U-Boot patches:
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/215802

Changes since v2:
- Updated binding documentation

Changes since v1:
- Nest nfc_config struct within the main nfc struct
- Use assigned clock binding to specify NFC clock
- Rebased ontop of MSCM IR patchset (driver parts have been merged)
- Split out arch Kconfig in a separate config
- Fix module license
- Updated MAINTAINERS

Changes since RFC (Bill Pringlemeir):
- Renamed driver from fsl_nfc to vf610_nfc
- Use readl/writel for all register in accessor functions
- Optimized field accessor functions
- Implemented PM (suspend/resume) functions
- Implemented basic support for ECC strength/ECC step size from dt
- Improved performance of count_written_bits by using hweight32
- Support ECC with 60-bytes to correct up to 32 bit errors
- Changed to in-band BBT (NAND_BBT_NO_OOB) which also allows ECC modes
which uses up to 60 bytes on 64 byte OOB
- Removed custom (downstream) BBT pattern since BBT table won't be
compatible anyway (due to the change above)

Stefan Agner (6):
mtd: nand: vf610_nfc: Freescale NFC for VF610, MPC5125 and others
mtd: nand: vf610_nfc: add hardware BCH-ECC support
mtd: nand: vf610_nfc: add device tree bindings
ARM: vf610: enable NAND Flash Controller
ARM: dts: vf610: add NAND flash controller peripherial
ARM: dts: vf-colibri: enable NAND flash controller

.../devicetree/bindings/mtd/vf610-nfc.txt | 45 ++
MAINTAINERS | 6 +
arch/arm/boot/dts/vf-colibri.dtsi | 32 +
arch/arm/boot/dts/vf610-twr.dts | 44 ++
arch/arm/boot/dts/vfxxx.dtsi | 8 +
arch/arm/mach-imx/Kconfig | 1 +
drivers/mtd/nand/Kconfig | 14 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/vf610_nfc.c | 859 +++++++++++++++++++++
9 files changed, 1010 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/vf610-nfc.txt
create mode 100644 drivers/mtd/nand/vf610_nfc.c

--
2.3.3

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/