Re: [PATCH] video: ARM CLCD: Added dt support to set tim2 register

[Arun Ramamurthy]

On 15-03-02 08:11 AM, Pawel Moll wrote:
> On Wed, 2015-02-25 at 21:01 +0000, Arun Ramamurthy wrote:
> > Added code based on linaro tree:
> > http://git.linaro.org/kernel/linux-linaro-stable.git
> > with commit id:6846e7822c4cab5a84672baace3b768c2d0db142
> > at drivers/video/amba-clcd.c. This lets the driver set
> > certain tim2 register bits after reading them from
> > device tree.
> >
> > Reviewed-by: Ray Jui <rjui@xxxxxxxxxxxx>
> > Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx>
> > Signed-off-by: Arun Ramamurthy <arun.ramamurthy@xxxxxxxxxxxx>
> > ---
> >   .../devicetree/bindings/video/arm,pl11x.txt        | 17 ++++++++-
> >   drivers/video/fbdev/amba-clcd.c                    | 41 ++++++++++++++++++++++
> >   2 files changed, 57 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/video/arm,pl11x.txt b/Documentation/devicetree/bindings/video/arm,pl11x.txt
> > index 3e3039a..14d6f87 100644
> > --- a/Documentation/devicetree/bindings/video/arm,pl11x.txt
> > +++ b/Documentation/devicetree/bindings/video/arm,pl11x.txt
> > @@ -35,6 +35,21 @@ Optional properties:
> >   	cell's memory interface can handle; if not present, the memory
> >   	interface is fast enough to handle all possible video modes
> >
> > +- tim2: Used to set certain bits in LCDTiming2 register.
> > +	It can be TIM2_CLKSEL or TIM2_IOE or both
> > +
> > +	TIM2_CLKSEL: This bit drives the CLCDCLKSEL signal. It is the select
> > +	signal for the external LCD clock multiplexor.
> > +
> > +	TIM2_IOE: Invert output enable:
> > +	0 = CLAC output pin is active HIGH in TFT mode
> > +	1 = CLAC output pin is active LOW in TFT mode.
> > +	This bit selects the active polarity of the output enable signal in
> > +	TFT mode. In this mode, the CLAC pin is an enable that indicates to
> > +	the LCD panel when valid display data is available. In active
> > +	display mode, data is driven onto the LCD data lines at the
> > +	programmed edge of CLCP when CLAC is in its active state.
> > +
>
> The existing bindings intentionally avoided quoting internal registers -
> they are supposed to describe how the hardware is wired up...
>
> So how about something like "arm,pl11x,tft-invert-clac"? Then the driver
> sets the bit or not, depending on the property existance?
Sure, I can change it to two properties called arm,pl11x,tft-invert-clac 
and arm,pl11x,tft-clksel. Would that be acceptable?

> Pawel
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/