Re: [PATCH RFC 02/12] Documentation: thermal docbook: add glossary

[Randy Dunlap]

On 02/09/15 13:34, Eduardo Valentin wrote:
> This change introduces a section in the Introduction Chapter to
> list concepts used by the Thermal Framework.
> 
> Signed-off-by: Eduardo Valentin <edubezval@xxxxxxxxx>
> ---
>  Documentation/DocBook/thermal.tmpl | 129 ++++++++++++++++++++++++++++++++++++-
>  1 file changed, 128 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/DocBook/thermal.tmpl b/Documentation/DocBook/thermal.tmpl
> index f8fb8a2..66efed3 100644
> --- a/Documentation/DocBook/thermal.tmpl
> +++ b/Documentation/DocBook/thermal.tmpl
> @@ -84,5 +84,132 @@
>  		devices.
>  		</para>
>  
> -  </chapter>
> +		<sect1 id="glossary">
> +			<title>Glossary</title>
> +			<para>The Linux Kernel Thermal Framework  uses a
> +			specific terminology to represent the entities involved
> +			in thermal constrained environments. This section
> +			summaries the terminology as dictionary. These terms are

			summarizes

> +			in use within the present document and in the source
> +			code of the Linux Kernel Thermal Framework.
> +			</para>
> +			<glossary>
> +				<glossentry>
> +					<glossterm>Thermal Zone</glossterm>
> +					<glossdef>
> +						<para>Thermal zones represent
> +						what is the current status of a
> +						thermal constrained zone in the
> +						hardware. The zone usually is a
> +						device or component. The status
> +						of a thermal zone is mainly with
> +						respect to temperature.
> +						Currently, the Linux Kernel
> +						Thermal Framework represents
> +						temperature in miliCelsius. The
> +						current abstraction covers for
> +						non negative temperatures and

						non-negative

> +						constraints.
> +						</para>
> +					</glossdef>
> +				</glossentry>
> +				<glossentry>
> +					<glossterm>Thermal Sensors</glossterm>
> +					<glossdef>
> +						<para>Thermal sensors provide
> +						temperature sensing capabilities
> +						on thermal zones. Typical
> +						devices are I2C ADC converters
> +						and bandgaps. These are nodes
> +						providing temperature data to
> +						thermal zones. Thermal sensor
> +						devices may control one or more
> +						internal sensors.
> +						</para>
> +					</glossdef>
> +				</glossentry>
> +				<glossentry>
> +					<glossterm>Trips Points</glossterm>

					           Trip Points

> +					<glossdef>
> +						<para>The trip node describes a
> +						point in the temperature domain
> +						in which the system takes an
> +						action. This item describes just
> +						the point, not the action. Trip
> +						points are represented as
> +						temperature in miliCelsius. The
> +						current abstraction covers for
> +						non negative temperatures.

						non-negative

> +						</para>
> +					</glossdef>
> +				</glossentry>
> +				<glossentry>
> +					<glossterm>Thermal Governor</glossterm>
> +					<glossdef>
> +						<para>Thermal Governors
> +						represent a policy to manage the
> +						thermal zone device temperature.
> +						The governor targets to keep
> +						temperature in an acceptable
> +						range which correlates to the
> +						power budget, while maximizing
> +						the performance. Governors can
> +						be implemented in Kernel Space
> +						or in User Space.
> +						</para>
> +					</glossdef>
> +				</glossentry>
> +				<glossentry>
> +					<glossterm>Thermal Cooling Device</glossterm>
> +					<glossdef>
> +						<para>Cooling devices provide
> +						control on power dissipation.
> +						There are essentially two ways
> +						to provide control on power
> +						dissipation. First is by means
> +						of regulating device
> +						performance, which is known as
> +						passive cooling. A typical
> +						passive cooling is a CPU that
> +						has dynamic voltage and
> +						frequency scaling (DVFS), and
> +						uses lower frequencies as
> +						cooling states. Second is by
> +						means of activating devices in
> +						order to remove the dissipated
> +						heat, which is known as active
> +						cooling, e.g. regulating fan
> +						speeds. In both cases, cooling
> +						devices shall have a way to
> +						determine the state of cooling
> +						in which the device is.
> +				</para>
> +					</glossdef>
> +				</glossentry>
> +				<glossentry>
> +					<glossterm>Cooling State</glossterm>
> +					<glossdef>
> +						<para>Any cooling device has a
> +						range of cooling states (i.e.
> +						different levels of heat
> +						dissipation). For example a
> +						fan's cooling states correspond
> +						to the different fan speeds
> +						possible. Cooling states are
> +						referred to by single unsigned
> +						integers, where larger numbers
> +						mean greater heat dissipation.
> +						The precise set of cooling
> +						states associated with a device
> +						(as referred to be the
> +						cooling-min-state and
> +						cooling-max-state properties)
> +						should be defined in a
> +						particular device's binding.
> +						</para>
> +					</glossdef>
> +				</glossentry>
> +			</glossary>
> +		</sect1>
> +	</chapter>
>  </book>
> 


-- 
~Randy
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/