Re: [PATCH 2/8] fbdev: ssd1307fb: Unify init code and make controller configurable from device tree

[Noralf TrÃnnes]

Hi,

Den 07.02.2015 15:59, skrev Thomas NiederprÃm:
> Am Sat, 7 Feb 2015 11:42:25 +0100
> schrieb Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>:
>
> > Hi,
> >
> > On Fri, Feb 06, 2015 at 11:28:08PM +0100, niederp@xxxxxxxxxxxxxxxx
> > wrote:
> > > From: Thomas NiederprÃm <niederp@xxxxxxxxxxxxxxxx>
> > >
> > > This patches unifies the init code for the ssd130X chips and
> > > adds device tree bindings to describe the hardware configuration
> > > of the used controller. This gets rid of the magic bit values
> > > used in the init code so far.
> > >
> > > Signed-off-by: Thomas NiederprÃm <niederp@xxxxxxxxxxxxxxxx>
> > > ---
> > >   .../devicetree/bindings/video/ssd1307fb.txt        |  11 +
> > >   drivers/video/fbdev/ssd1307fb.c                    | 243
> > > ++++++++++++++------- 2 files changed, 174 insertions(+), 80
> > > deletions(-)
> > >
> > > diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt
> > > b/Documentation/devicetree/bindings/video/ssd1307fb.txt index
> > > 7a12542..1230f68 100644 ---
> > > a/Documentation/devicetree/bindings/video/ssd1307fb.txt +++
> > > b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -15,6
> > > +15,17 @@ Required properties:
> > >   Optional properties:
> > >     - reset-active-low: Is the reset gpio is active on physical low?
> > > +  - solomon,segment-remap: Invert the order of data column to
> > > segment mapping
> > > +  - solomon,offset: Map the display start line to one of COM0 -
> > > COM63
> > > +  - solomon,contrast: Set initial contrast of the display
> > > +  - solomon,prechargep1: Set the duration of the precharge period
> > > phase1
> > > +  - solomon,prechargep2: Set the duration of the precharge period
> > > phase2
> > > +  - solomon,com-alt: Enable/disable alternate COM pin configuration
> > > +  - solomon,com-lrremap: Enable/disable left-right remap of COM
> > > pins
> > > +  - solomon,com-invdir: Invert COM scan direction
> > > +  - solomon,vcomh: Set VCOMH regulator voltage
> > > +  - solomon,dclk-div: Set display clock divider
> > > +  - solomon,dclk-frq: Set display clock frequency
> > I'm sorry, but this is the wrong approach, for at least two reasons:
> > you broke all existing users of that driver, which is a clear no-go,
> Unfortunately this is true. The problem is that the SSD130X controllers
> allow for a very versatile wiring of the display to the controller.
> It's over to the manufacturer of the OLED module (disp+controller) to
> decide how it's actually wired and during device initialization the
> driver has to take care to configure the SSD130X controller according
> to that wiring. If the driver fails to do so you will end up having
> your display showing garbage. Unfortunately the current sate of the
> initialization code of the ssd1307fb driver is not very flexible in that
> respect. Taking a look at the initialization code for the ssd1306 shows
> that it was written with one very special display module in mind. Most
> of the magic bit values set there are non-default values according to
> the datasheet. The result is that the driver works with that one
> particular display module but many other (differently wired) display
> modules using a ssd1306 controller won't work without changing the
> hardcoded magic bit values.
>
> My idea here was to set all configuration to the default values (as
> given in the datasheet) unless it is overwritten by DT. Of course,
> without a change in DT, this breaks the driver for all existing users.
> The only alternative would be to set the current values as default.
> Somehow this feels wrong to me as these values look arbitrary when you
> don't know what exact display module they were set for. But if you
> insist, I will change the default values.
>
> > and the DT itself should not contain any direct mapping of the
> > registers.
> I think I don't get what you mean here. Is it because I do no sanity
> checks of the numbers set in DT? I was just looking for a way to hand
> over the information about the wiring of display to the driver. How
> would you propose to solve this?

I have the exact same challenge with the staging/fbtft drivers.
I have asked about this on the DT list a couple of days ago, but no 
answer yet:

Can I do register initialization from Device Tree?
http://www.spinics.net/lists/devicetree/msg68174.html


Regards,
Noralf TrÃnnes

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/