Re: [PATCH/RFC v10 03/19] DT: leds: Add led-sources property

From: Jacek Anaszewski
Date: Tue Jan 13 2015 - 03:42:51 EST


On 01/12/2015 05:55 PM, Rob Herring wrote:
Adding Mark B and Liam...

On Mon, Jan 12, 2015 at 10:10 AM, Jacek Anaszewski
<j.anaszewski@xxxxxxxxxxx> wrote:
On 01/12/2015 02:52 PM, Rob Herring wrote:

On Mon, Jan 12, 2015 at 2:32 AM, Jacek Anaszewski
<j.anaszewski@xxxxxxxxxxx> wrote:
On 01/09/2015 07:33 PM, Rob Herring wrote:
On Fri, Jan 9, 2015 at 9:22 AM, Jacek Anaszewski
<j.anaszewski@xxxxxxxxxxx> wrote:
Add a property for defining the device outputs the LED
represented by the DT child node is connected to.

[...]

b/Documentation/devicetree/bindings/leds/common.txt
index a2c3f7a..29295bf 100644
--- a/Documentation/devicetree/bindings/leds/common.txt
+++ b/Documentation/devicetree/bindings/leds/common.txt
@@ -1,6 +1,10 @@
Common leds properties.

Optional properties for child nodes:
+- led-sources : Array of bits signifying the LED current regulator
outputs the
+ LED represented by the child node is connected to (1 -
the LED
+ is connected to the output, 0 - the LED isn't connected
to the
+ output).



Sorry, I just don't understand this.



In some Flash LED devices one LED can be connected to one or more
electric current outputs, which allows for multiplying the maximum
current allowed for the LED. Each sub-LED is represented by a child
node in the DT binding of the Flash LED device and it needs to declare
which outputs it is connected to. In the example below the led-sources
property is a two element array, which means that the flash LED device
has two current outputs, and the bits signify if the LED is connected
to the output.


Sounds like a regulator for which we already have bindings for and we
have a driver for regulator based LEDs (but no binding for it).


Do you think of drivers/leds/leds-regulator.c driver? This driver just
allows for registering an arbitrary regulator device as a LED subsystem
device.

There are however devices that don't fall into this category, i.e. they
have many outputs, that can be connected to a single LED or to many LEDs
and the driver has to know what is the actual arrangement.

We may need to extend the regulator binding slightly and allow for
multiple phandles on a supply property, but wouldn't something like
this work:

led-supply = <&led-reg0>, <&led-reg1>, <&led-reg2>, <&led-reg3>;

The shared source is already supported by the regulator binding.

I think that we shouldn't split the LED devices into power supply
providers and consumers as in case of generic regulators. From this
point of view a LED device current output is a provider and a discrete
LED element is a consumer. In this approach each discrete LED element
should have a related driver which is not how LED devices are being
handled in the LED subsystem, where there is a single binding for a LED
device and there is a single driver for it which creates separate LED
class devices for each LED connected to the LED device output. Each
discrete LED is represented by a child node in the LED device binding.

I am aware that it may be tempting to treat LED devices as common
regulators, but they have their specific features which gave a
reason for introducing LED class for them. Besides, there is already
drivers/leds/leds-regulator.c driver for LED devices which support only
turning on/off and setting brightness level.

In your proposition a separate regulator provider binding would have
to be created for each current output and a separate binding for
each discrete LED connected to the LED device. It would create
unnecessary noise in a dts file.

Moreover, using regulator binding implies that we want to treat it
as a sheer power supply for our device (which would be a discrete LED
element in this case), whereas LED devices provide more features like
blinking pattern and for flash LED devices - flash timeout, external
strobe and flash faults.

--
Best Regards,
Jacek Anaszewski
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/