[PATCH 02/25] phy: miphy28lp: Add Device Tree bindings for the MiPHY28lp

From: Kishon Vijay Abraham I
Date: Thu Nov 27 2014 - 01:34:18 EST


From: Gabriel FERNANDEZ <gabriel.fernandez@xxxxxx>

The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe
or USB3 devices.

Signed-off-by: alexandre torgue <alexandre.torgue@xxxxxx>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@xxxxxx>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@xxxxxxxxxx>
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
.../devicetree/bindings/phy/phy-miphy28lp.txt | 126 ++++++++++++++++++++
1 file changed, 126 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-miphy28lp.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
new file mode 100644
index 0000000..b7c13ad
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
@@ -0,0 +1,126 @@
+STMicroelectronics STi MIPHY28LP PHY binding
+============================================
+
+This binding describes a miphy device that is used to control PHY hardware
+for SATA, PCIe or USB3.
+
+Required properties (controller (parent) node):
+- compatible : Should be "st,miphy28lp-phy".
+- st,syscfg : Should be a phandle of the system configuration register group
+ which contain the SATA, PCIe or USB3 mode setting bits.
+
+Required nodes : A sub-node is required for each channel the controller
+ provides. Address range information including the usual
+ 'reg' and 'reg-names' properties are used inside these
+ nodes to describe the controller's topology. These nodes
+ are translated by the driver's .xlate() function.
+
+Required properties (port (child) node):
+- #phy-cells : Should be 1 (See second example)
+ Cell after port phandle is device type from:
+ - PHY_TYPE_SATA
+ - PHY_TYPE_PCI
+ - PHY_TYPE_USB3
+- reg : Address and length of the register set for the device.
+- reg-names : The names of the register addresses corresponding to the registers
+ filled in "reg". It can also contain the offset of the system configuration
+ registers used as glue-logic to setup the device for SATA/PCIe or USB3
+ devices.
+- resets : phandle to the parent reset controller.
+- reset-names : Associated name must be "miphy-sw-rst".
+
+Optional properties (port (child) node):
+- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This
+ is not available in all the MiPHY. For example, for STiH407, only the
+ MiPHY0 has this bit.
+- st,osc-force-ext : to select the external oscillator. This can change from
+ different MiPHY inside the same SoC.
+- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config
+ register.
+- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive
+ line).
+
+example:
+
+ miphy28lp_phy: miphy28lp@9b22000 {
+ compatible = "st,miphy28lp-phy";
+ st,syscfg = <&syscfg_core>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ phy_port0: port@9b22000 {
+ reg = <0x9b22000 0xff>,
+ <0x9b09000 0xff>,
+ <0x9b04000 0xff>,
+ <0x114 0x4>, /* sysctrl MiPHY cntrl */
+ <0x818 0x4>, /* sysctrl MiPHY status*/
+ <0xe0 0x4>, /* sysctrl PCIe */
+ <0xec 0x4>; /* sysctrl SATA */
+ reg-names = "sata-up",
+ "pcie-up",
+ "pipew",
+ "miphy-ctrl-glue",
+ "miphy-status-glue",
+ "pcie-glue",
+ "sata-glue";
+ #phy-cells = <1>;
+ st,osc-rdy;
+ reset-names = "miphy-sw-rst";
+ resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
+ };
+
+ phy_port1: port@9b2a000 {
+ reg = <0x9b2a000 0xff>,
+ <0x9b19000 0xff>,
+ <0x9b14000 0xff>,
+ <0x118 0x4>,
+ <0x81c 0x4>,
+ <0xe4 0x4>,
+ <0xf0 0x4>;
+ reg-names = "sata-up",
+ "pcie-up",
+ "pipew",
+ "miphy-ctrl-glue",
+ "miphy-status-glue",
+ "pcie-glue",
+ "sata-glue";
+ #phy-cells = <1>;
+ st,osc-force-ext;
+ reset-names = "miphy-sw-rst";
+ resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
+ };
+
+ phy_port2: port@8f95000 {
+ reg = <0x8f95000 0xff>,
+ <0x8f90000 0xff>,
+ <0x11c 0x4>,
+ <0x820 0x4>;
+ reg-names = "pipew",
+ "usb3-up",
+ "miphy-ctrl-glue",
+ "miphy-status-glue";
+ #phy-cells = <1>;
+ reset-names = "miphy-sw-rst";
+ resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
+ };
+ };
+
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the miphy device node and an index
+specifying which configuration to use, as described in phy-bindings.txt.
+
+example:
+ sata0: sata@9b20000 {
+ ...
+ phys = <&phy_port0 PHY_TYPE_SATA>;
+ ...
+ };
+
+Macro definitions for the supported miphy configuration can be found in:
+
+include/dt-bindings/phy/phy-miphy28lp.h
--
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/