Re: [PATCH v5 05/14] clk: Add generic driver for Maxim PMIC clocks

From: Javier Martinez Canillas
Date: Wed Jul 02 2014 - 06:13:43 EST


Hello Mike,

On 07/01/2014 07:26 PM, Mike Turquette wrote:
> Quoting Yadwinder Singh Brar (2014-06-29 21:01:36)
>> Hi Javier,
>>
>> On Thu, Jun 26, 2014 at 11:45 PM, Javier Martinez Canillas
>> <javier.martinez@xxxxxxxxxxxxxxx> wrote:
>> > Maxim Integrated Power Management ICs are very similar with
>> > regard to their clock outputs. Most of the clock drivers for
>> > these chips are duplicating code and are simpler enough that
>> > can be converted to use a generic driver to consolidate code
>> > and avoid duplication.
>> >
>> > Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
>> > Reviewed-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
>> > ---
>> >
>> > Changes since v4:
>> > - Return recalc 0 if clock isn't enabled in Suggested by Yadwinder Singh Brar.
>> >
>>
>> It seems you didn't implement or posted same patch again :) .
>>
>> > Changes since v3:
>> > - Add current copyright information. Suggested by Krzysztof Kozlowski
>> > - Do a single allocation for struct max_gen_clk. Suggested by Krzysztof Kozlowski
>> > - Add EXPORT_SYMBOL() for exported symbols. Suggested by Krzysztof Kozlowski
>> >
>> > drivers/clk/Kconfig | 3 +
>> > drivers/clk/Makefile | 1 +
>> > drivers/clk/clk-max-gen.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++
>> > drivers/clk/clk-max-gen.h | 32 ++++++++
>> > 4 files changed, 231 insertions(+)
>> > create mode 100644 drivers/clk/clk-max-gen.c
>> > create mode 100644 drivers/clk/clk-max-gen.h
>> >
>>
>> [ .. ]
>>
>> > +
>> > +static unsigned long max_gen_recalc_rate(struct clk_hw *hw,
>> > + unsigned long parent_rate)
>> > +{
>> > + return 32768;
>> > +}
>>
>> Its still same here.
>
> Changing this would be a new behavior. I do not know of any other clock
> drivers that conditionally returns a rate of 0 based on whether or not
> the clock is gated.
>

After Yadwinder feedback I searched for clock drivers that returned 0 when the
clock was not enabled/prepared and found for example drivers/clk/clk-s2mps11.c:


static unsigned long s2mps11_clk_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
struct s2mps11_clk *s2mps11 = to_s2mps11_clk(hw);
if (s2mps11->enabled)
return 32768;
else
return 0;
}

> It is also buggy since calls to clk_enable and clk_disable do not invoke
> .recalc_rate, so the rate of your clock would not be updated from the
> framework's perspective until some later point where you call
> clk_set_rate or something.
>

s2ps11->enabled is set in the driver's clk_ops .prepare and .unprepare function
handlers and calls to clk_prepare and clk_unprepare also don't seems to invoke
.recalc_rate so I guess that driver is wrong as well and should just return the
clock rate unconditionally?

> If your driver needs to know whether or not the clock is enabled then we
> could introduce a new bool clk_is_enabled(struct clk *clk); to clk.h,
> but I'd rather not do that. Instead if a driver needs a clock then it
> calls clk_enable on it without any knowledge about the internal state of
> the clock enable_count.
>
> Regards,
> Mike
>

Thanks a lot for the explanation, I'll revert that change then and return the
clock rate unconditionally on the next version of the patch-set.

Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/