[PATCH 1/6] Documentation: dt: add omap mailbox bindings

From: Suman Anna
Date: Tue Jun 24 2014 - 21:49:01 EST


Add the device tree bindings document for OMAP2+ mailbox.

Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Pawel Moll <pawel.moll@xxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
Cc: Kumar Gala <galak@xxxxxxxxxxxxxx>
Signed-off-by: Suman Anna <s-anna@xxxxxx>
---
.../devicetree/bindings/mailbox/omap-mailbox.txt | 104 +++++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mailbox/omap-mailbox.txt

diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt
new file mode 100644
index 0000000..307c4bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt
@@ -0,0 +1,104 @@
+OMAP2+ Mailbox Driver
+=====================
+
+The OMAP mailbox hardware facilitates communication between different processors
+using a queued mailbox interrupt mechanism. The IP block is external to the
+various processor subsystems and is connected on an interconnect bus. The
+communication is achieved through a set of registers for message storage and
+interrupt configuration registers.
+
+Each mailbox IP block has a certain number of h/w fifo queues and output
+interrupt lines. An output interrupt line is routed to an interrupt controller
+within a processor subsystem, and there can be more than one line going to a
+specific processor's interrupt controller. The interrupt line connections are
+fixed for an instance and are dictated by the IP integration into the SoC
+(excluding the SoCs that have a Interrupt Crossbar IP). Each interrupt line is
+programmable through a set of interrupt configuration registers, and have a rx
+and tx interrupt source per h/w fifo. Communication between different processors
+is achieved through the appropriate programming of the rx and tx interrupt
+sources on the appropriate interrupt lines.
+
+The number of h/w fifo queues and interrupt lines dictate the usable registers.
+All the current OMAP SoCs except for the newest DRA7xx SoC has a single IP
+instance. DRA7xx has multiple instances with different number of h/w fifo queues
+and interrupt lines between different instances. The interrupt lines can also be
+routed to different processor sub-systems on DRA7xx as they are routed through
+the Crossbar, a kind of interrupt router/multiplexer.
+
+Mailbox Device Node:
+====================
+A Mailbox device node is used to represent a Mailbox IP instance within a SoC.
+The sub-mailboxes are represented as child node of this parent node.
+
+Required properties:
+--------------------
+- compatible: Should be one of the following,
+ "ti,omap2-mailbox" for OMAP2420, OMAP2430 SoCs
+ "ti,omap3-mailbox" for OMAP3430, OMAP3630 SoCs
+ "ti,am3352-mailbox" for AM33xx SoCs
+ "ti,am4372-mailbox" for AM43xx SoCs
+ "ti,omap4-mailbox" for OMAP44xx, OMAP54xx SoCs and
+ DRA7xx Mailbox1 instance
+ "ti,dra7-mailbox" for DRA7xx (except for Mailbox1
+ instance)
+- reg: Contains the mailbox register address range (base
+ address and length)
+- interrupts: Contains the interrupt information for the mailbox
+ device. The format is dependent on which interrupt
+ controller the OMAP device uses
+- ti,hwmods: Name of the hwmod associated with the mailbox
+
+Child Nodes:
+============
+A child node is used for representing the actual sub-mailbox device that is
+used for the communication between the host processor and a remote processor.
+Each child node should have a unique node name.
+
+Required properties:
+--------------------
+- ti,mbox-tx: sub-mailbox descriptor property defining a Tx fifo
+- ti,mbox-rx: sub-mailbox descriptor property defining a Rx fifo
+
+Sub-mailbox Descriptor Data
+---------------------------
+Each of the above ti,mbox-tx and ti,mbox-rx properties should have 3 cells of
+data that represent the following:
+ Cell #1 (fifo_id) - mailbox fifo id used either for transmitting
+ (ti,mbox-tx) or for receiving (ti,mbox-rx)
+ Cell #2 (irq_id) - irq identifier index number to use from the parent's
+ interrupts data. Should be 0 for most of the cases, a
+ positive index value is seen only on mailboxes that have
+ multiple interrupt lines connected to the MPU processor.
+ Cell #3 (usr_id) - mailbox user id for identifying the interrupt line
+ associated with generating a tx/rx fifo interrupt.
+
+Example:
+--------
+
+/* OMAP4 */
+mailbox: mailbox@4a0f4000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x4a0f4000 0x200>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mailbox";
+ mbox_ipu: mbox_ipu {
+ ti,mbox-tx = <0 0 0>;
+ ti,mbox-rx = <1 0 0>;
+ };
+ mbox_dsp: mbox_dsp {
+ ti,mbox-tx = <3 0 0>;
+ ti,mbox-rx = <2 0 0>;
+ };
+};
+
+/* AM33xx */
+mailbox: mailbox@480C8000 {
+ compatible = "ti,am3352-mailbox";
+ reg = <0x480C8000 0x200>;
+ interrupts = <77>;
+ ti,hwmods = "mailbox";
+ mbox_wkupm3: wkup_m3 {
+ ti,mbox-tx = <0 0 0>;
+ ti,mbox-rx = <0 0 3>;
+ };
+};
--
2.0.0

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/