Re: [PATCH 21/22] ARM: sunxi: Add Allwinner A23 dtsi

From: Chen-Yu Tsai
Date: Mon May 26 2014 - 00:02:47 EST


On Mon, May 26, 2014 at 3:38 AM, Maxime Ripard
<maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
> On Fri, May 23, 2014 at 03:51:24PM +0800, Chen-Yu Tsai wrote:
>> The Allwinner A23 is a tablet oriented SoC with 2 Cortex-A7 cores
>> and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
>> ---
>> arch/arm/boot/dts/sun8i-a23.dtsi | 524 +++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 524 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-a23.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-a23.dtsi b/arch/arm/boot/dts/sun8i-a23.dtsi
>> new file mode 100644
>> index 0000000..1cff087
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-a23.dtsi
>> @@ -0,0 +1,524 @@
>> +/*
>> + * Copyright 2014 Chen-Yu Tsai
>> + *
>> + * Chen-Yu Tsai <wens@xxxxxxxx>
>> + *
>> + * The code contained herein is licensed under the GNU General Public
>> + * License. You may obtain a copy of the GNU General Public License
>> + * Version 2 or later at the following locations:
>> + *
>> + * http://www.opensource.org/licenses/gpl-license.html
>> + * http://www.gnu.org/copyleft/gpl.html
>> + */
>> +
>> +/include/ "skeleton.dtsi"
>> +
>> +/ {
>> + interrupt-parent = <&gic>;
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + serial1 = &uart1;
>> + serial2 = &uart2;
>> + serial3 = &uart3;
>> + serial4 = &uart4;
>> + serial5 = &r_uart;
>> + };
>> +
>> +
>> + cpus {
>> + enable-method = "allwinner,sun8i-a23";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu@0 {
>> + compatible = "arm,cortex-a7";
>> + device_type = "cpu";
>> + reg = <0>;
>> + clocks = <&cpu>;
>> + };
>> +
>> + cpu@1 {
>> + compatible = "arm,cortex-a7";
>> + device_type = "cpu";
>> + reg = <1>;
>> + clocks = <&cpu>;
>
> The clocks attributes have not been merged yet.

I'll drop them until they are merged.

>> + };
>> + };
>> +
>> + memory {
>> + reg = <0x40000000 0x80000000>;
>> + };
>> +
>> + pmu {
>> + compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
>> + interrupts = <0 120 4>,
>> + <0 121 4>,
>> + <0 122 4>,
>> + <0 123 4>;
>> + };
>
> The PMU usually have as much interrupts as CPU core, so this is most
> likely wrong.

I see. I just copied the interrupts that were listed in Allwinner sources.
I'll drop the extra 2.

> Also, do you know if the arch timers are usable on the A23?

I tried them (copying the "timer" section from A20 dtsi), but the system
just hangs. I think I'll leave this for a follow up series.

>> +
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + osc24M: osc24M_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <24000000>;
>> + clock-output-names = "osc24M";
>> + };
>> +
>> + osc32k: osc32k_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <32768>;
>> + clock-output-names = "osc32k";
>> + };
>> +
>> + pll1: clk@01c20000 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun8i-a23-pll1-clk";
>> + reg = <0x01c20000 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "pll1";
>> + };
>> +
>> + pll6: clk@01c20028 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-pll6-clk";
>> + reg = <0x01c20028 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "pll6_other", "pll6";
>> + };
>> +
>> + cpu: cpu_clk@01c20050 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-cpu-clk";
>> + reg = <0x01c20050 0x4>;
>> +
>> + /*
>> + * PLL1 is listed twice here.
>> + * While it looks suspicious, it's actually documented
>> + * that way both in the datasheet and in the code from
>> + * Allwinner.
>> + */
>> + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
>> + clock-output-names = "cpu";
>> + };
>> +
>> + axi: axi_clk@01c20050 {
>> + #clock-cells = <0>;
>> + /*
>> + * AXI clock on A23 is actually wider,
>> + * but extra bit is useless for divider
>> + */
>
> Then please add a new compatible for this, even though we're not doing
> anything differently (yet).

Will do.

>> + compatible = "allwinner,sun4i-a10-axi-clk";
>> + reg = <0x01c20050 0x4>;
>> + clocks = <&cpu>;
>> + clock-output-names = "axi";
>> + };
>> +
>> + ahb1_pll6: ahb1_pll6_clk@01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-ahb1-pll6-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&pll6 0>;
>> + clock-output-names = "ahb1_pll6";
>> + };
>> +
>> + ahb1_mux: ahb1_mux_clk@01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-ahb1-mux-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&axi>, <&ahb1_pll6>;
>> + clock-output-names = "ahb1_mux";
>> + };
>> +
>> + ahb1: ahb1_clk@01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-ahb-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&ahb1_mux>;
>> + clock-output-names = "ahb1";
>> + };
>> +
>> + ahb1_gates: clk@01c20060 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun8i-a23-ahb1-gates-clk";
>> + reg = <0x01c20060 0x8>;
>> + clocks = <&ahb1>;
>> + clock-output-names = "ahb1_mipidsi", "ahb1_dma",
>> + "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2",
>> + "ahb1_nand", "ahb1_sdram",
>> + "ahb1_hstimer", "ahb1_spi0",
>> + "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
>> + "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
>> + "ahb1_csi", "ahb1_be", "ahb1_fe",
>> + "ahb1_gpu", "ahb1_spinlock",
>> + "ahb1_drc";
>> + };
>> +
>> + apb1: apb1_clk@01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-apb0-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&ahb1>;
>> + clock-output-names = "apb1";
>> + };
>> +
>> + apb1_gates: clk@01c20068 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun8i-a23-apb1-gates-clk";
>> + reg = <0x01c20068 0x4>;
>> + clocks = <&apb1>;
>> + clock-output-names = "apb1_codec", "apb1_pio",
>> + "apb1_daudio0", "apb1_daudio1";
>> + };
>> +
>> + apb2_mux: apb2_mux@01c20058 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-apb1-mux-clk";
>> + reg = <0x01c20058 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
>> + clock-output-names = "apb2_mux";
>> + };
>
> It doesn't look to be ordered by physical address.

My bad.

>> + apb2: apb2@01c20058 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-apb2-div-clk";
>> + reg = <0x01c20058 0x4>;
>> + clocks = <&apb2_mux>;
>> + clock-output-names = "apb2";
>> + };
>> +
>> + apb2_gates: clk@01c2006c {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun8i-a23-apb2-gates-clk";
>> + reg = <0x01c2006c 0x4>;
>> + clocks = <&apb2>;
>> + clock-output-names = "apb2_i2c0", "apb2_i2c1",
>> + "apb2_i2c2", "apb2_uart0",
>> + "apb2_uart1", "apb2_uart2",
>> + "apb2_uart3", "apb2_uart4";
>> + };
>> +
>> + mmc0_clk: clk@01c20088 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c20088 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>;
>> + clock-output-names = "mmc0";
>> + };
>> +
>> + mmc1_clk: clk@01c2008c {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c2008c 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>;
>> + clock-output-names = "mmc1";
>> + };
>> +
>> + mmc2_clk: clk@01c20090 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c20090 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>;
>> + clock-output-names = "mmc2";
>> + };
>> +
>> + spi0_clk: clk@01c200a0 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c200a0 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>;
>> + clock-output-names = "spi0";
>> + };
>> +
>> + spi1_clk: clk@01c200a4 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-mod0-clk";
>> + reg = <0x01c200a4 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>;
>> + clock-output-names = "spi1";
>> + };
>> + };
>> +
>> + soc@01c00000 {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + pio: pinctrl@01c20800 {
>> + compatible = "allwinner,sun8i-a23-pinctrl";
>> + reg = <0x01c20800 0x400>;
>> + interrupts = <0 11 4>,
>> + <0 15 4>,
>> + <0 17 4>;
>> + clocks = <&apb1_gates 5>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #gpio-cells = <3>;
>> +
>> + uart0_pins_a: uart0@0 {
>> + allwinner,pins = "PF2", "PF4";
>> + allwinner,function = "uart0";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + i2c0_pins_a: i2c0@0 {
>> + allwinner,pins = "PH2", "PH3";
>> + allwinner,function = "i2c0";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + i2c1_pins_a: i2c1@0 {
>> + allwinner,pins = "PH4", "PH5";
>> + allwinner,function = "i2c1";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> + };
>> +
>> + ahb1_rst: reset@01c202c0 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-ahb1-reset";
>> + reg = <0x01c202c0 0xc>;
>> + };
>> +
>> + apb1_rst: reset@01c202d0 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + reg = <0x01c202d0 0x4>;
>> + };
>> +
>> + apb2_rst: reset@01c202d8 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + reg = <0x01c202d8 0x4>;
>> + };
>> +
>> + timer@01c20c00 {
>> + compatible = "allwinner,sun4i-a10-timer";
>> + reg = <0x01c20c00 0xa0>;
>> + interrupts = <0 18 4>,
>> + <0 19 4>;
>> + clocks = <&osc24M>;
>> + };
>> +
>> + wdt0: watchdog@01c20ca0 {
>> + compatible = "allwinner,sun6i-a31-wdt";
>> + reg = <0x01c20ca0 0x20>;
>> + interrupts = <0 25 4>;
>> + };
>> +
>> + uart0: serial@01c28000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28000 0x400>;
>> + interrupts = <0 0 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 16>;
>> + resets = <&apb2_rst 16>;
>> + status = "disabled";
>> + };
>> +
>> + uart1: serial@01c28400 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28400 0x400>;
>> + interrupts = <0 1 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 17>;
>> + resets = <&apb2_rst 17>;
>> + status = "disabled";
>> + };
>> +
>> + uart2: serial@01c28800 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28800 0x400>;
>> + interrupts = <0 2 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 18>;
>> + resets = <&apb2_rst 18>;
>> + status = "disabled";
>> + };
>> +
>> + uart3: serial@01c28c00 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28c00 0x400>;
>> + interrupts = <0 3 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 19>;
>> + resets = <&apb2_rst 19>;
>> + status = "disabled";
>> + };
>> +
>> + uart4: serial@01c29000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c29000 0x400>;
>> + interrupts = <0 4 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb2_gates 20>;
>> + resets = <&apb2_rst 20>;
>> + status = "disabled";
>> + };
>> +
>> + i2c0: i2c@01c2ac00 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2ac00 0x400>;
>> + interrupts = <0 6 4>;
>> + clocks = <&apb2_gates 0>;
>> + clock-frequency = <100000>;
>> + resets = <&apb2_rst 0>;
>> + status = "disabled";
>> + };
>> +
>> + i2c1: i2c@01c2b000 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2b000 0x400>;
>> + interrupts = <0 7 4>;
>> + clocks = <&apb2_gates 1>;
>> + clock-frequency = <100000>;
>> + resets = <&apb2_rst 1>;
>> + status = "disabled";
>> + };
>> +
>> + i2c2: i2c@01c2b400 {
>> + compatible = "allwinner,sun6i-a31-i2c";
>> + reg = <0x01c2b400 0x400>;
>> + interrupts = <0 8 4>;
>> + clocks = <&apb2_gates 2>;
>> + clock-frequency = <100000>;
>> + resets = <&apb2_rst 2>;
>> + status = "disabled";
>> + };
>> +
>> + spi0: spi@01c68000 {
>> + compatible = "allwinner,sun6i-a31-spi";
>> + reg = <0x01c68000 0x1000>;
>> + interrupts = <0 65 4>;
>> + clocks = <&ahb1_gates 20>, <&spi0_clk>;
>> + clock-names = "ahb", "mod";
>> + resets = <&ahb1_rst 20>;
>> + status = "disabled";
>> + };
>> +
>> + spi1: spi@01c69000 {
>> + compatible = "allwinner,sun6i-a31-spi";
>> + reg = <0x01c69000 0x1000>;
>> + interrupts = <0 66 4>;
>> + clocks = <&ahb1_gates 21>, <&spi1_clk>;
>> + clock-names = "ahb", "mod";
>> + resets = <&ahb1_rst 21>;
>> + status = "disabled";
>> + };
>> +
>> + gic: interrupt-controller@01c81000 {
>> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
>> + reg = <0x01c81000 0x1000>,
>> + <0x01c82000 0x1000>;
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> + };
>> +
>> + nmi_intc: interrupt-controller@01f00c0c {
>> + compatible = "allwinner,sun6i-a31-sc-nmi";
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + reg = <0x01f00c0c 0x38>;
>> + interrupts = <0 32 4>;
>> + };
>> +
>> + prcm@01f01400 {
>> + compatible = "allwinner,sun8i-a23-prcm";
>> + reg = <0x01f01400 0x200>;
>> +
>> + ar100: ar100_clk {
>> + compatible = "fixed-factor-clock";
>> + #clock-cells = <0>;
>> + clock-div = <1>;
>> + clock-mult = <1>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "ar100";
>> + };
>> +
>> + ahb0: ahb0_clk {
>> + compatible = "fixed-factor-clock";
>> + #clock-cells = <0>;
>> + clock-div = <1>;
>> + clock-mult = <1>;
>> + clocks = <&ar100>;
>> + clock-output-names = "ahb0";
>> + };
>> +
>> + apb0: apb0_clk {
>> + compatible = "allwinner,sun8i-a23-apb0-clk";
>> + #clock-cells = <0>;
>> + clocks = <&ahb0>;
>> + clock-output-names = "apb0";
>> + };
>> +
>> + apb0_gates: apb0_gates_clk {
>> + compatible = "allwinner,sun6i-a31-apb0-gates-clk";
>> + #clock-cells = <1>;
>> + clocks = <&apb0>;
>> + clock-indices = <0>, <2>, <3>, <4>, <6>;
>> + clock-output-names = "apb0_pio", "apb0_timer",
>> + "apb0_rsb", "apb0_uart",
>> + "apb0_i2c";
>> + };
>> +
>> + apb0_rst: apb0_rst {
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + #reset-cells = <1>;
>> + };
>> + };
>> +
>> + cpucfg@01f01c00 {
>> + compatible = "allwinner,sun8i-a23-cpuconfig";
>> + reg = <0x01f01c00 0x300>;
>> + };
>> +
>> + r_uart: serial@01f02800 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01f02800 0x400>;
>> + interrupts = <0 38 4>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&apb0_gates 4>;
>> + resets = <&apb0_rst 4>;
>> + status = "disabled";
>> + };
>> +
>> + r_pio: pinctrl@01f02c00 {
>> + compatible = "allwinner,sun8i-a23-r-pinctrl";
>> + reg = <0x01f02c00 0x400>;
>> + interrupts = <0 45 4>;
>> + clocks = <&apb0_gates 0>;
>> + resets = <&apb0_rst 0>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #gpio-cells = <3>;
>> +
>> + r_uart_pins_a: r_uart@0 {
>> + allwinner,pins = "PL2", "PL3";
>> + allwinner,function = "s_uart";
>> + allwinner,drive = <0>;
>> + allwinner,pull = <0>;
>> + };
>> +
>> + };
>> + };
>> +};
>
> Thanks,
> Maxime

Thanks for the review.
ChenYu
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/