Re: [PATCH 1/1] regulator: Add new driver for ST's PWM controlled voltage regulators

From: Josh Cartwright
Date: Thu Mar 20 2014 - 11:31:57 EST


Hey Lee-

A few minor things below.

On Thu, Mar 20, 2014 at 02:10:54PM +0000, Lee Jones wrote:
> On some STMicroelectronics hardware reside regulators consisting
> partly of a PWM input connected to the feedback loop. As the PWM
> duty-cycle is varied the output voltage adapts. This driver
> allows us to vary the output voltage by adapting the PWM input
> duty-cycle.
>
> Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
> --- /dev/null
> +++ b/drivers/regulator/st-pwm.c
> +static int st_pwm_regulator_set_voltage(struct regulator_dev *dev,
> + int min_uV, int max_uV,
> + unsigned *selector)
> +{
> + struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
> + int dutycycle, best_val = INT_MAX;
> + int sel, ret;
> +
> + for (sel = 0; sel < dev->desc->n_voltages; sel++) {
> + if (drvdata->duty_cycle_table[sel].uV < best_val &&
> + drvdata->duty_cycle_table[sel].uV >= min_uV &&
> + drvdata->duty_cycle_table[sel].uV <= max_uV) {
> + best_val = drvdata->duty_cycle_table[sel].uV;
> + if (selector)
> + *selector = sel;
> + }
> + }

If you implement .set_voltage_sel() instead and set map_voltage to
regulator_map_voltage_iterate, the core can take care of this.

> +
> + if (best_val == INT_MAX)
> + return -EINVAL;
> +
> + dutycycle = (ST_PWM_REG_PERIOD / 100) *
> + drvdata->duty_cycle_table[sel].dutycycle;

Considering (ST_PWM_REG_PERIOD / 100) is constant, could you get away
with dropping this calculation by just putting the already-adjusted
values into your duty cycle table?

> +
> + ret = pwm_config(drvdata->pwm, dutycycle, ST_PWM_REG_PERIOD);
> + if (ret) {
> + dev_err(&dev->dev, "Failed to configure PWM\n");
> + return ret;
> + }
> +
> + drvdata->state = sel;
> +
> + if (!drvdata->enabled) {
> + ret = pwm_enable(drvdata->pwm);
> + if (ret) {
> + dev_err(&dev->dev, "Failed to enable PWM\n");
> + return ret;
> + }
> + drvdata->enabled = true;
> + }
> +
> + return 0;
> +}
> +
> +static int st_pwm_regulator_list_voltage(struct regulator_dev *dev,
> + unsigned selector)
> +{
> + struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
> +
> + if (selector >= dev->desc->n_voltages)
> + return -EINVAL;
> +
> + return drvdata->duty_cycle_table[selector].uV;
> +}
> +
> +static struct regulator_ops st_pwm_regulator_voltage_ops = {
> + .get_voltage = st_pwm_regulator_get_voltage,
> + .set_voltage = st_pwm_regulator_set_voltage,
> + .list_voltage = st_pwm_regulator_list_voltage,
> +};
> +
> +static struct st_pwm_voltages b2105_duty_cycle_table[] = {
> + { .uV = 1114000, .dutycycle = 0, },
> + { .uV = 1095000, .dutycycle = 10, },
> + { .uV = 1076000, .dutycycle = 20, },
> + { .uV = 1056000, .dutycycle = 30, },
> + { .uV = 1036000, .dutycycle = 40, },
> + { .uV = 996000, .dutycycle = 50, },
> + /* WARNING: Values above 50% duty-cycle cause boot failures. */
> +};
> +
> +static struct regulator_desc b2105_desc = {
> + .name = "b2105-pwm-regulator",
> + .ops = &st_pwm_regulator_voltage_ops,
> + .type = REGULATOR_VOLTAGE,
> + .owner = THIS_MODULE,
> + .n_voltages = ARRAY_SIZE(b2105_duty_cycle_table),
> + .supply_name = "pwm",
> +};
> +
> +static struct st_pwm_regulator_data b2105_info = {
> + .desc = &b2105_desc,
> + .duty_cycle_table = b2105_duty_cycle_table,
> +};
> +
> +static struct of_device_id st_pwm_of_match[] = {

const. At least the regulator_desc and duty cycle table should be const
as well. (see my comments below about b2105_info).

> + { .compatible = "st,b2105-pwm-regulator", .data = &b2105_info, },
> + { },
> +};

You may want a MODULE_DEVICE_TABLE(of, ...); here if you want to be able
to be autoloaded.

> +
> +static int st_pwm_regulator_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct st_pwm_regulator_data *drvdata;
> + const struct of_device_id *of_match;
> + struct regulator_dev *regulator;
> + struct regulator_config config = { };
> +
> + if (!np) {
> + dev_err(&pdev->dev, "Device Tree node missing\n");
> + return -EINVAL;
> + }
> +
> + of_match = of_match_device(st_pwm_of_match, &pdev->dev);
> + if (!of_match) {
> + dev_err(&pdev->dev, "failed to match of device\n");
> + return -ENODEV;
> + }
> + drvdata = (struct st_pwm_regulator_data *) of_match->data;

Hrm, I typed "cast not necessary here", but then I realized it is
necessary since you using it to cast away constness.

Are you safe assuming that there will only be one of these devices in a
system? It doesn't seem like much a burden to just allocate a new
object and use it instead of a statically allocated one.

--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/