Re: [PATCH 5/5] ARM: dts: exynos4412-trats2: Add ADC's dt data to get temperature of SoC/battery

From: Chanwoo Choi
Date: Wed Mar 12 2014 - 02:02:13 EST


Hi Tomasz,

On 03/11/2014 10:09 PM, Tomasz Figa wrote:
> Hi Chanwoo,
>
> On 11.03.2014 08:54, Chanwoo Choi wrote:
>> This patch use ADC to get the temperature of SoC/battery by using NTC thermistor
>> driver in hwmon. NTC thermistor driver covnvert ADC's raw data to temperature
>> by using following variables:
>>
>> - pullup-uv : Voltage
>> - pullup-ohm : Pull-up resistance
>> - pulldown-ohm : Pull-down resistance
>> - io-channels : It means ADC channel.
>>
>
> Those properties are well-defined in "ntc,ncp15wb473" DT bindings documentation. There is no need to repeat them here.
>
>> Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> ---
>> arch/arm/boot/dts/exynos4412-trats2.dts | 21 +++++++++++++++++++++
>> 1 file changed, 21 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
>> index 4f851cc..fc517c3 100644
>> --- a/arch/arm/boot/dts/exynos4412-trats2.dts
>> +++ b/arch/arm/boot/dts/exynos4412-trats2.dts
>> @@ -106,6 +106,27 @@
>> };
>> };
>>
>> + adc: adc@126C0000 {
>> + vdd-supply = <&ldo3_reg>;
>> + status = "okay";
>> +
>> + ncp15wb473@0 {
>
> style: Nodes should have generic names, e.g. thermistor@0.
>
> Also if node name is suffixed with @unit-address, then the node should have a reg property with its first entry corresponding to the unit-address. Now there is no physical unit-address definition for those thermistors, so they shouldn't use this naming pattern, but rather something like "thermistor-0" or "thermistor-ap".

OK I'll rename thermistor dt name.
>
>> + compatible = "ntc,ncp15wb473";
>> + pullup-uv = <1800000>; /* VCC_1.8V_AP */
>> + pullup-ohm = <100000>; /* 100K */
>> + pulldown-ohm = <100000>; /* 100K */
>> + io-channels = <&adc 1>; /* AP temperature */
>> + };
>> +
>> + ncp15wb473@1 {
>> + compatible = "ntc,ncp15wb473";
>> + pullup-uv = <1800000>; /* VCC_1.8V_AP */
>> + pullup-ohm = <100000>; /* 100K */
>> + pulldown-ohm = <100000>; /* 100K */
>> + io-channels = <&adc 2>; /* Battery temperature */
>> + };
>
> Anyway, I don't think it is correct to place IIO consumers under IIO provider node, because IIO is not a control bus, but rather a resource provider, like GPIO, clock, etc. So both thermistor nodes should be placed outside the adc node. (They might be grouped in a simple-bus subnode, though, to improve readability.)

OK, I'll move ntc_thermistor node outside of ADC dt node.

Best Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/