[PATCH RESEND v4 33/37] mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back

From: Lee Jones
Date: Thu Jan 23 2014 - 05:33:17 EST


Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
drivers/mtd/devices/st_spi_fsm.c | 82 +++++++++++++++++++++++++++++++++++++++-
1 file changed, 81 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index 1b0fa67..92071fa 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -324,6 +324,7 @@ struct flash_info {
};

static int stfsm_n25q_config(struct stfsm *fsm);
+static int stfsm_mx25_config(struct stfsm *fsm);

static struct flash_info flash_types[] = {
/*
@@ -355,7 +356,8 @@ static struct flash_info flash_types[] = {
FLASH_FLAG_SE_4K | \
FLASH_FLAG_SE_32K)
{ "mx25l25635e", 0xc22019, 0, 64*1024, 512,
- (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70, NULL }
+ (MX25_FLAG | FLASH_FLAG_32BIT_ADDR | FLASH_FLAG_RESET), 70,
+ stfsm_mx25_config },

#define N25Q_FLAG (FLASH_FLAG_READ_WRITE | \
FLASH_FLAG_READ_FAST | \
@@ -507,6 +509,31 @@ static struct seq_rw_config n25q_read4_configs[] = {
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
};

+/*
+ * [MX25xxx] Configuration
+ */
+#define MX25_STATUS_QE (0x1 << 6)
+
+static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq)
+{
+ seq->seq_opc[0] = (SEQ_OPC_PADS_1 |
+ SEQ_OPC_CYCLES(8) |
+ SEQ_OPC_OPCODE(FLASH_CMD_EN4B_ADDR) |
+ SEQ_OPC_CSDEASSERT);
+
+ seq->seq[0] = STFSM_INST_CMD1;
+ seq->seq[1] = STFSM_INST_WAIT;
+ seq->seq[2] = STFSM_INST_STOP;
+
+ seq->seq_cfg = (SEQ_CFG_PADS_1 |
+ SEQ_CFG_ERASE |
+ SEQ_CFG_READNOTWRITE |
+ SEQ_CFG_CSDEASSERT |
+ SEQ_CFG_STARTSEQ);
+
+ return 0;
+}
+
static struct stfsm_seq stfsm_seq_read; /* Dynamically populated */
static struct stfsm_seq stfsm_seq_write; /* Dynamically populated */
static struct stfsm_seq stfsm_seq_en_32bit_addr;/* Dynamically populated */
@@ -1033,6 +1060,59 @@ static int stfsm_prepare_rwe_seqs_default(struct stfsm *fsm)
return 0;
}

+static int stfsm_mx25_config(struct stfsm *fsm)
+{
+ uint32_t flags = fsm->info->flags;
+ uint32_t data_pads;
+ uint8_t sta;
+ int ret;
+ bool soc_reset;
+
+ /*
+ * Use default READ/WRITE sequences
+ */
+ ret = stfsm_prepare_rwe_seqs_default(fsm);
+ if (ret)
+ return ret;
+
+ /*
+ * Configure 32-bit Address Support
+ */
+ if (flags & FLASH_FLAG_32BIT_ADDR) {
+ /* Configure 'enter_32bitaddr' FSM sequence */
+ stfsm_mx25_en_32bit_addr_seq(&stfsm_seq_en_32bit_addr);
+
+ soc_reset = stfsm_can_handle_soc_reset(fsm);
+ if (soc_reset || !fsm->booted_from_spi) {
+ /* If we can handle SoC resets, we enable 32-bit address
+ * mode pervasively */
+ stfsm_enter_32bit_addr(fsm, 1);
+
+ } else {
+ /* Else, enable/disable 32-bit addressing before/after
+ * each operation */
+ fsm->configuration = (CFG_READ_TOGGLE_32BIT_ADDR |
+ CFG_WRITE_TOGGLE_32BIT_ADDR |
+ CFG_ERASESEC_TOGGLE_32BIT_ADDR);
+ /* It seems a small delay is required after exiting
+ * 32-bit mode following a write operation. The issue
+ * is under investigation.
+ */
+ fsm->configuration |= CFG_WRITE_EX_32BIT_ADDR_DELAY;
+ }
+ }
+
+ /* For QUAD mode, set 'QE' STATUS bit */
+ data_pads = ((stfsm_seq_read.seq_cfg >> 16) & 0x3) + 1;
+ if (data_pads == 4) {
+ stfsm_read_status(fsm, FLASH_CMD_RDSR, &sta);
+ sta |= MX25_STATUS_QE;
+ stfsm_write_status(fsm, sta, 1);
+ }
+
+ return 0;
+}
+
static int stfsm_n25q_config(struct stfsm *fsm)
{
uint32_t flags = fsm->info->flags;
--
1.8.3.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/