Re: using mmc2 on panda [was: Regression 3.11-rc1: omap4panda:no usb and consequently no ethernet]
From: Arend van Spriel
Date: Wed Oct 02 2013 - 06:21:00 EST
On 10/01/2013 01:29 PM, Luca Coelho wrote:
Hi,
On Tue, 2013-10-01 at 12:53 +0200, Arend van Spriel wrote:
On 10/01/2013 11:53 AM, Roger Quadros wrote:
On 10/01/2013 12:49 PM, Roger Quadros wrote:
Hi Arend,
On 10/01/2013 11:05 AM, Arend van Spriel wrote:
On 07/19/2013 12:57 PM, Arend van Spriel wrote:
On 07/19/2013 12:49 PM, Roger Quadros wrote:
On 07/19/2013 01:36 PM, Arend van Spriel wrote:
On 07/18/2013 10:59 AM, Tony Lindgren wrote:
Then for the SDIO with device tree, take a look at the following
patches:
[PATCH 0/3] WLAN support for omap4 when booted with devicetree
http://comments.gmane.org/gmane.linux.ports.arm.omap/97522#
I have been looking at the pandaboard patch in the series above and I
do have a question. Among other things the patch adds these dt entries.
+ 0x108 0x118 /* sdmmc5_clk.sdmmc5_clk INPUT_PULLUP |
MODE0 */
+ 0x10a 0x118 /* sdmmc5_cmd.sdmmc5_cmd INPUT_PULLUP |
MODE0 */
If I look at the similar names in the deceased board-omap4panda.c:
board-omap4panda.c: OMAP4_MUX(SDMMC5_CMD, OMAP_MUX_MODE0 |
OMAP_PIN_INPUT_PULLUP),
board-omap4panda.c: OMAP4_MUX(SDMMC5_CLK, OMAP_MUX_MODE0 |
OMAP_PIN_INPUT_PULLUP),
and in mux44xx.h:
mux44xx.h:#define OMAP4_CTRL_MODULE_PAD_SDMMC5_CLK_OFFSET 0x0148
mux44xx.h:#define OMAP4_CTRL_MODULE_PAD_SDMMC5_CMD_OFFSET 0x014a
So how did 0x0148 get 0x0108 in DT and 0x014a get 0x010a. There is
probably an explanation to it and it would help my understanding to
know where this difference comes from. Hope you can help me out here.
If you see omap4.dtsi, omap4_pmx_core starts at register address
0x4a100040.
So, you need to subtract 0x40 from the offsets defined in mux44xx.h
for pmx_core registers.
That was what I was looking for. Thanks!
Hi Roger,
It has been a while, but I would like to pickup this thread. We have a couple of pandaboards used as test setup. These have an SDIO adapter hooked up to expansion connector A using MMC2. I have attached the patch file (just ignore platform_data stuff). Now on one board it works, but not for the other. I suspect a board issue so listing the two types that we use:
PandaBoard rev A2 (dmesg: OMAP4430 ES2.1): works
PandaBoardES rev B1 (dmesg: OMAP4460 ES1.1): nope
Any hints for me.
Does your PandaboardES have the WLAN chip (U4) mounted? If yes, how do you isolate
it from your external SDIO adapter?
On my 4460 board in front of me U4 is not populated, but U3 is (the TiWi
thing).
OK, just realized that the expansion connector uses different pads for MMC2. However, you still
need to make sure that the other pins (connected to on board WLAN chip) are not muxed as MMC2.
I think Luciano added DT patches for on-board WLAN and it uses MMC5 if I
am not mistaken(?). Attached are the dmesg logs of the two boards.
I sent 2 patch series to add DT support for the on-board WLAN, but they
were not applied, since there were some comments that required changes.
I really don't have the time to revisit them now that I'm not with TI
anymore, so I'm hoping someone else will pick them up at some point.
I found this one in my email archive:
[PATCH v2 0/4] ARM: dts: add WiLink support to panda and omap4-sdp
Guess that is what you are referring to, right?
Gr. AvS
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/